firmware/variants/tlora_v1/variant.h

#define I2C_SDA 4 // I2C pins for this board
#define I2C_SCL 15

#define RESET_OLED 16 // If defined, this pin will be used to reset the display controller

#define VEXT_ENABLE 21 // active low, powers the oled display and the lora antenna boost
#define VEXT_ON_VALUE LOW
#define LED_PIN 2    // If defined we will blink this LED
#define BUTTON_PIN 0 // If defined, this will be used for user button presses
#define BUTTON_NEED_PULLUP
#define EXT_NOTIFY_OUT 13 // Default pin to use for Ext Notify Module.

#define USE_RF95
#define LORA_DIO0 26 // a No connect on the SX1262 module
#define LORA_RESET 14
#define LORA_DIO1 33 // Must be manually wired: https://www.thethingsnetwork.org/forum/t/big-esp32-sx127x-topic-part-3/18436
#define LORA_DIO2 32 // Not really used
Initial configuration.h -> variants refactor (#1104) * Initial configuration to variants refactor 2022-01-19 00:35:42 +00:00			`#define I2C_SDA 4 // I2C pins for this board`
			`#define I2C_SCL 15`

			`#define RESET_OLED 16 // If defined, this pin will be used to reset the display controller`

fix TLora V1 Boards Display Init 2022-11-21 14:50:47 +00:00			`#define VEXT_ENABLE 21 // active low, powers the oled display and the lora antenna boost`
Make specifying VEXT_ON_VALUE manatory if using VEXT_ENABLE 2024-08-22 18:07:06 +00:00			`#define VEXT_ON_VALUE LOW`
			`#define LED_PIN 2 // If defined we will blink this LED`
			`#define BUTTON_PIN 0 // If defined, this will be used for user button presses`
Initial configuration.h -> variants refactor (#1104) * Initial configuration to variants refactor 2022-01-19 00:35:42 +00:00			`#define BUTTON_NEED_PULLUP`
more rename plugin to module 2022-02-27 10:21:02 +00:00			`#define EXT_NOTIFY_OUT 13 // Default pin to use for Ext Notify Module.`
Initial configuration.h -> variants refactor (#1104) * Initial configuration to variants refactor 2022-01-19 00:35:42 +00:00
			`#define USE_RF95`
			`#define LORA_DIO0 26 // a No connect on the SX1262 module`
			`#define LORA_RESET 14`
Use LORA_DIO1 as RadioLib GPIO for SX127x chips (#2290) * When channel is active, first try receiving that packet Afterwards we'll try transmitting again * Remove setStandby in startSend Already done in isChannelActive() * Set LORA_DIO1 as RadioLib GPIO for SX127x * LORA_DIO1 for Heltec v1, overlaps with GPS_TX Set to RADIOLIB_NC for now * If receive was not successful, startReceive doesn't trigger the interrupt So we have to go back to transmitting anyway --------- Co-authored-by: Ben Meadors <benmmeadors@gmail.com> 2023-02-20 13:40:44 +00:00			`#define LORA_DIO1 33 // Must be manually wired: https://www.thethingsnetwork.org/forum/t/big-esp32-sx127x-topic-part-3/18436`
Remove GPS pins from devices lacking built-in GPS (#2812) 2023-09-19 15:55:14 +00:00			`#define LORA_DIO2 32 // Not really used`