firmware/variants/tlora_v2_1_16/variant.h

#undef GPS_RX_PIN
#undef GPS_TX_PIN
#define GPS_RX_PIN 15 // per @der_bear on the forum, 36 is incorrect for this board type and 15 is a better pick
#define GPS_TX_PIN 13

#define BATTERY_PIN 35
#define ADC_CHANNEL ADC1_GPIO35_CHANNEL
#define BATTERY_SENSE_SAMPLES 30

// ratio of voltage divider = 2.0 (R42=100k, R43=100k)
#define ADC_MULTIPLIER 2

#define I2C_SDA 21 // I2C pins for this board
#define I2C_SCL 22

#define LED_PIN 25    // If defined we will blink this LED
#define BUTTON_PIN 12 // If defined, this will be used for user button presses,

#define BUTTON_NEED_PULLUP

#define USE_RF95
#define LORA_DIO0 26 // a No connect on the SX1262 module
#define LORA_RESET 23
#define LORA_DIO1 33 // https://www.thethingsnetwork.org/forum/t/big-esp32-sx127x-topic-part-3/18436
#define LORA_DIO2 32 // Not really used
Initial configuration.h -> variants refactor (#1104) * Initial configuration to variants refactor 2022-01-19 00:35:42 +00:00			`#undef GPS_RX_PIN`
			`#undef GPS_TX_PIN`
			`#define GPS_RX_PIN 15 // per @der_bear on the forum, 36 is incorrect for this board type and 15 is a better pick`
			`#define GPS_TX_PIN 13`

Implementing a calibrated ESP32 ADC reading 2023-05-14 00:38:37 +00:00			`#define BATTERY_PIN 35`
Add ADC channels to esp variants, plug code back in to make sure other archs work 2023-05-16 05:40:42 +00:00			`#define ADC_CHANNEL ADC1_GPIO35_CHANNEL`
Implementing a calibrated ESP32 ADC reading 2023-05-14 00:38:37 +00:00			`#define BATTERY_SENSE_SAMPLES 30`

Correction for wrong battery display on tlora_v2_1_16 board (#1120) * Update variant.h 2022-01-21 02:47:30 +00:00			`// ratio of voltage divider = 2.0 (R42=100k, R43=100k)`
Implementing a calibrated ESP32 ADC reading 2023-05-14 00:38:37 +00:00			`#define ADC_MULTIPLIER 2`
Initial configuration.h -> variants refactor (#1104) * Initial configuration to variants refactor 2022-01-19 00:35:42 +00:00
			`#define I2C_SDA 21 // I2C pins for this board`
			`#define I2C_SCL 22`

trunk roundhouse kick 2023-01-21 13:34:29 +00:00			`#define LED_PIN 25 // If defined we will blink this LED`
			`#define BUTTON_PIN 12 // If defined, this will be used for user button presses,`
Initial configuration.h -> variants refactor (#1104) * Initial configuration to variants refactor 2022-01-19 00:35:42 +00:00
			`#define BUTTON_NEED_PULLUP`

			`#define USE_RF95`
			`#define LORA_DIO0 26 // a No connect on the SX1262 module`
Updated pinut in variant tlorav2_1_16 (#1365) * Added the last mac address bytes in bluetooth device name ESP32Bluetooth.cpp Add default notification pinout to tlora_v2_1_16/variant.h * updated ADC_MULTIPLIER value for more accuracy * Update variant.h Updated LORA_RESET GPIO in this board is 23 Removed LORA_DIO1 35 , gpio 35 is a battery pin Removed LORA_DIO2 34, gpio 34 is unuse in this board Co-authored-by: Ben Meadors <benmmeadors@gmail.com> Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com> 2022-04-12 12:13:25 +00:00			`#define LORA_RESET 23`
Use LORA_DIO1 as RadioLib GPIO for SX127x chips (#2290) * When channel is active, first try receiving that packet Afterwards we'll try transmitting again * Remove setStandby in startSend Already done in isChannelActive() * Set LORA_DIO1 as RadioLib GPIO for SX127x * LORA_DIO1 for Heltec v1, overlaps with GPS_TX Set to RADIOLIB_NC for now * If receive was not successful, startReceive doesn't trigger the interrupt So we have to go back to transmitting anyway --------- Co-authored-by: Ben Meadors <benmmeadors@gmail.com> 2023-02-20 13:40:44 +00:00			`#define LORA_DIO1 33 // https://www.thethingsnetwork.org/forum/t/big-esp32-sx127x-topic-part-3/18436`
Implementing a calibrated ESP32 ADC reading 2023-05-14 00:38:37 +00:00			`#define LORA_DIO2 32 // Not really used`