mirror of
https://github.com/meshtastic/firmware.git
synced 2025-02-01 10:19:59 +00:00
63 lines
2.7 KiB
C
63 lines
2.7 KiB
C
|
// LED - status indication
|
||
|
|
#define LED_PIN 37
|
||
|
|
|
||
|
|
// Button - user interface
|
||
|
|
#define BUTTON_PIN 0 // This is the BOOT button, and it has its own pull-up resistor
|
||
|
|
|
||
|
|
// SD card - TODO: test, currently untested, copied from T3S3 variant
|
||
|
|
#define HAS_SDCARD
|
||
|
|
#define SDCARD_USE_SPI1
|
||
|
|
// TODO: rename this to make this SD-card specific
|
||
|
|
#define SPI_CS 13
|
||
|
|
#define SPI_SCK 14
|
||
|
|
#define SPI_MOSI 11
|
||
|
|
#define SPI_MISO 2
|
||
|
|
// FIXME: there are two other SPI pins that are not defined here
|
||
|
|
// Compatibility
|
||
|
|
#define SDCARD_CS SPI_CS
|
||
|
|
|
||
|
|
// Battery voltage monitoring - TODO: test, currently untested, copied from T3S3 variant
|
||
|
|
#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
|
||
|
|
#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
|
||
|
|
#define ADC_MULTIPLIER \
|
||
|
|
2.11 // ratio of voltage divider = 2.0 (R10=1M, R13=1M), plus some undervoltage correction - TODO: this was carried over from
|
||
|
|
// the T3S3, test to see if the undervoltage correction is needed.
|
||
|
|
|
||
|
|
// Display - OLED connected via I2C by the default hardware configuration
|
||
|
|
#define HAS_SCREEN 1
|
||
|
|
#define USE_SSD1306
|
||
|
|
#define I2C_SCL 17
|
||
|
|
#define I2C_SDA 18
|
||
|
|
|
||
|
|
// UART - The 1mm JST SH connector closest to the USB-C port
|
||
|
|
#define UART_TX 43
|
||
|
|
#define UART_RX 44
|
||
|
|
|
||
|
|
// Peripheral I2C - The 1mm JST SH connector furthest from the USB-C port which follows Adafruit connection standard. There are no
|
||
|
|
// pull-up resistors on these lines, the downstream device needs to include them. TODO: test, currently untested
|
||
|
|
#define I2C_SCL1 21
|
||
|
|
#define I2C_SDA1 10
|
||
|
|
|
||
|
|
// Radio
|
||
|
|
#define USE_SX1262 // CDEBYTE EoRa-S3-900TB <- CDEBYTE E22-900MM22S <- Semtech SX1262
|
||
|
|
#define USE_SX1268 // CDEBYTE EoRa-S3-400TB <- CDEBYTE E22-400MM22S <- Semtech SX1268
|
||
|
|
|
||
|
|
#define SX126X_CS 7
|
||
|
|
#define LORA_SCK 5
|
||
|
|
#define LORA_MOSI 6
|
||
|
|
#define LORA_MISO 3
|
||
|
|
#define SX126X_RESET 8
|
||
|
|
#define SX126X_BUSY 34
|
||
|
|
#define SX126X_DIO1 33
|
||
|
|
|
||
|
|
#define SX126X_DIO2_AS_RF_SWITCH // All switching is performed with DIO2, it is automatically inverted using circuitry.
|
||
|
|
// CDEBYTE EoRa-S3 uses an XTAL, thus we do not need DIO3 as TCXO voltage reference. Don't define SX126X_DIO3_TCXO_VOLTAGE for
|
||
|
|
// simplicity rather than defining it as 0.
|
||
|
|
#define SX126X_MAX_POWER \
|
||
|
|
22 // E22-900MM22S and E22-400MM22S have a raw SX1262 or SX1268 respsectively, they are rated to output up and including 22
|
||
|
|
// dBm out of their SX126x IC.
|
||
|
|
|
||
|
|
// Compatibility with old variant.h file structure - FIXME: this should be done in the respective radio interface modules to clean
|
||
|
|
// up all variants.
|
||
|
|
#define LORA_CS SX126X_CS
|
||
|
|
#define LORA_DIO1 SX126X_DIO1
|