firmware/variants/diy/nrf52_promicro_diy_tcxo/variant.h

#ifndef _VARIANT_PROMICRO_DIY_
#define _VARIANT_PROMICRO_DIY_

/** Master clock frequency */
#define VARIANT_MCK (64000000ul)

// #define USE_LFXO // Board uses 32khz crystal for LF
#define USE_LFRC // Board uses RC for LF

#define PROMICRO_DIY_TCXO

/*----------------------------------------------------------------------------
 *        Headers
 *----------------------------------------------------------------------------*/

#include "WVariant.h"

#ifdef __cplusplus
extern "C" {
#endif // __cplusplus

/*
NRF52 PRO MICRO PIN ASSIGNMENT

| Pin   | Function    |     | Pin      | Function     | RF95  |
| ----- | ----------- | --- | -------- | ------------ | ----- |
| Gnd   |             |     | vbat     |              |       |
| P0.06 | Serial2 RX  |     | vbat     |              |       |
| P0.08 | Serial2 TX  |     | Gnd      |              |       |
| Gnd   |             |     | reset    |              |       |
| Gnd   |             |     | ext_vcc  | *see 0.13    |       |
| P0.17 | RXEN        |     | P0.31    | BATTERY_PIN  |       |
| P0.20 | GPS_RX      |     | P0.29    | BUSY         | DIO0  |
| P0.22 | GPS_TX      |     | P0.02    | MISO         | MISO  |
| P0.24 | GPS_EN      |     | P1.15    | MOSI         | MOSI  |
| P1.00 | BUTTON_PIN  |     | P1.13    | CS           | CS    |
| P0.11 | SCL         |     | P1.11    | SCK          | SCK   |
| P1.04 | SDA         |     | P0.10    | DIO1/IRQ     | DIO1  |
| P1.06 | Free pin    |     | P0.09    | RESET        | RST   |
|       |             |     |          |              |       |
|       | Mid board   |     |          | Internal     |       |
| P1.01 | Free pin    |     | 0.15     | LED          |       |
| P1.02 | Free pin    |     | 0.13     | 3V3_EN       |       |
| P1.07 | Free pin    |     |          |              |       |
*/

// Number of pins defined in PinDescription array
#define PINS_COUNT (48)
#define NUM_DIGITAL_PINS (48)
#define NUM_ANALOG_INPUTS (1)
#define NUM_ANALOG_OUTPUTS (0)

// Pin 13 enables 3.3V periphery. If the Lora module is on this pin, then it should stay enabled at all times.
#define PIN_3V3_EN (0 + 13) // P0.13

// Analog pins
#define BATTERY_PIN (0 + 31) // P0.31 Battery ADC
#define ADC_CHANNEL ADC1_GPIO4_CHANNEL
#define ADC_RESOLUTION 14
#define BATTERY_SENSE_RESOLUTION_BITS 12
#define BATTERY_SENSE_RESOLUTION 4096.0
// Definition of milliVolt per LSB => 3.0V ADC range and 12-bit ADC resolution = 3000mV/4096
#define VBAT_MV_PER_LSB (0.73242188F)
// Voltage divider value => 1.5M + 1M voltage divider on VBAT = (1.5M / (1M + 1.5M))
#define VBAT_DIVIDER (0.6F)
// Compensation factor for the VBAT divider
#define VBAT_DIVIDER_COMP (1.73)
// Fixed calculation of milliVolt from compensation value
#define REAL_VBAT_MV_PER_LSB (VBAT_DIVIDER_COMP * VBAT_MV_PER_LSB)
#undef AREF_VOLTAGE
#define AREF_VOLTAGE 3.0
#define VBAT_AR_INTERNAL AR_INTERNAL_3_0
#define ADC_MULTIPLIER VBAT_DIVIDER_COMP // REAL_VBAT_MV_PER_LSB
#define VBAT_RAW_TO_SCALED(x) (REAL_VBAT_MV_PER_LSB * x)

// WIRE IC AND IIC PINS
#define WIRE_INTERFACES_COUNT 1

#define PIN_WIRE_SDA (32 + 4) // P1.04
#define PIN_WIRE_SCL (0 + 11) // P0.11

// LED
#define PIN_LED1 (0 + 15) // P0.15
#define LED_BUILTIN PIN_LED1
// Actually red
#define LED_BLUE PIN_LED1
#define LED_STATE_ON 1 // State when LED is lit

// Button
#define BUTTON_PIN (32 + 0) // P1.00

// GPS
#define PIN_GPS_TX (0 + 22) // P0.22
#define PIN_GPS_RX (0 + 20) // P0.20

#define PIN_GPS_EN (0 + 24) // P0.24
#define GPS_POWER_TOGGLE
#define GPS_UBLOX
// define GPS_DEBUG

// UART interfaces
#define PIN_SERIAL1_RX PIN_GPS_TX
#define PIN_SERIAL1_TX PIN_GPS_RX

#define PIN_SERIAL2_RX (0 + 6) // P0.06
#define PIN_SERIAL2_TX (0 + 8) // P0.08

// Serial interfaces
#define SPI_INTERFACES_COUNT 1

#define PIN_SPI_MISO (0 + 2)   // P0.02
#define PIN_SPI_MOSI (32 + 15) // P1.15
#define PIN_SPI_SCK (32 + 11)  // P1.11

#define LORA_MISO PIN_SPI_MISO
#define LORA_MOSI PIN_SPI_MOSI
#define LORA_SCK PIN_SPI_SCK
#define LORA_CS (32 + 13) // P1.13

// LORA MODULES
#define USE_LLCC68
#define USE_SX1262
#define USE_RF95
#define USE_SX1268

// RF95 CONFIG

#define LORA_DIO0 (0 + 29) // P0.10 IRQ
#define LORA_DIO1 (0 + 10) // P0.10 IRQ
#define LORA_RESET (0 + 9) // P0.09

// RX/TX for RFM95/SX127x
#define RF95_RXEN (0 + 17)    // P0.17
#define RF95_TXEN RADIOLIB_NC // Assuming that DIO2 is connected to TXEN pin. If not, TXEN must be connected.

// SX126X CONFIG
#define SX126X_CS (32 + 13)      // P1.13 FIXME - we really should define LORA_CS instead
#define SX126X_DIO1 (0 + 10)     // P0.10 IRQ
#define SX126X_DIO2_AS_RF_SWITCH // Note for E22 modules: DIO2 is not attached internally to TXEN for automatic TX/RX switching,
                                 // so it needs connecting externally if it is used in this way
#define SX126X_BUSY (0 + 29)     // P0.29
#define SX126X_RESET (0 + 9)     // P0.09
#define SX126X_RXEN (0 + 17)     // P0.17
#define SX126X_TXEN RADIOLIB_NC  // Assuming that DIO2 is connected to TXEN pin. If not, TXEN must be connected.

// #define SX126X_MAX_POWER 8 set this if using a high-power board!

/*
On the SX1262, DIO3 sets the voltage for an external TCXO, if one is present. If one is not present, use TCXO_OPTIONAL to try both
settings.

| Mfr          | Module           | TCXO | RF Switch | Notes                                 |
| ------------ | ---------------- | ---- | --------- | ------------------------------------- |
| Ebyte        | E22-900M22S      | Yes  | Ext       |                                       |
| Ebyte        | E22-900MM22S     | No   | Ext       |                                       |
| Ebyte        | E22-900M30S      | Yes  | Ext       |                                       |
| Ebyte        | E22-900M33S      | Yes  | Ext       | MAX_POWER must be set to 8 for this   |
| Ebyte        | E220-900M22S     | No   | Ext       | LLCC68, looks like DIO3 not connected |
| AI-Thinker   | RA-01SH          | No   | Int       | SX1262                                |
| Heltec       | HT-RA62          | Yes  | Int       |                                       |
| NiceRF       | Lora1262         | yes  | Int       |                                       |
| Waveshare    | Core1262-HF      | yes  | Ext       |                                       |
| Waveshare    | LoRa Node Module | yes  | Int       |                                       |
| Seeed        | Wio-SX1262       | yes  | Int       | Sooooo cute!                          |
| AI-Thinker   | RA-02            | No   | Int       | SX1278 **433mhz band only**           |
| RF Solutions | RFM95            | No   | Int       | Untested                              |

*/

#define SX126X_DIO3_TCXO_VOLTAGE 1.8
#define TCXO_OPTIONAL     // make it so that the firmware can try both TCXO and XTAL
extern float tcxoVoltage; // make this available everywhere

#ifdef __cplusplus
}
#endif

/*----------------------------------------------------------------------------
 *        Arduino objects - C++ only
 *----------------------------------------------------------------------------*/

#endif