diff --git a/variants/rak_wismeshtag/platformio.ini b/variants/rak_wismeshtag/platformio.ini
index 05dfb760d..a066e5282 100644
--- a/variants/rak_wismeshtag/platformio.ini
+++ b/variants/rak_wismeshtag/platformio.ini
@@ -6,49 +6,10 @@ board_check = true
 build_flags = ${nrf52840_base.build_flags} -Ivariants/rak_wismeshtag -D WISMESH_TAG -D RAK_4631
   -L "${platformio.libdeps_dir}/${this.__env__}/bsec2/src/cortex-m4/fpv4-sp-d16-hard"
   -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
-  -DEINK_WIDTH=250
-  -DEINK_HEIGHT=122
   -DRADIOLIB_EXCLUDE_SX128X=1
   -DRADIOLIB_EXCLUDE_SX127X=1
   -DRADIOLIB_EXCLUDE_LR11X0=1
-build_src_filter = ${nrf52_base.build_src_filter} +<../variants/rak_wismeshtag> +<mesh/eth/> +<mesh/api/> +<mqtt/>
+  -DMESHTASTIC_EXCLUDE_WIFI=1
+build_src_filter = ${nrf52_base.build_src_filter} +<../variants/rak_wismeshtag>
 lib_deps = 
-  ${nrf52840_base.lib_deps}
-  ${networking_base.lib_deps}
-  melopero/Melopero RV3028@^1.1.0
-  https://github.com/RAKWireless/RAK13800-W5100S/archive/1.0.2.zip
-  rakwireless/RAKwireless NCP5623 RGB LED library@^1.0.2
-  https://github.com/RAKWireless/RAK12034-BMX160/archive/dcead07ffa267d3c906e9ca4a1330ab989e957e2.zip
-
-; If not set we will default to uploading over serial (first it forces bootloader entry by talking 1200bps to cdcacm)
-; Note: as of 6/2013 the serial/bootloader based programming takes approximately 30 seconds
-;upload_protocol = jlink
-
-; Allows programming and debug via the RAK NanoDAP as the default debugger tool for the RAK4631 (it is only $10!)
-; programming time is about the same as the bootloader version.
-; For information on this see the meshtastic developers documentation for "Development on the NRF52"
-[env:rak4631_dbg]
-extends = env:rak4631
-board_level = extra
-
-; if the builtin version of openocd has a buggy version of semihosting, so use the external version
-; platform_packages = platformio/tool-openocd@^3.1200.0
-
-build_flags =
-  ${env:rak4631.build_flags}
-  -D USE_SEMIHOSTING
-
-lib_deps =
-  ${env:rak4631.lib_deps}
-  https://github.com/geeksville/Armduino-Semihosting/archive/35b538fdf208c3530c1434cd099a08e486672ee4.zip
-
-; NOTE: the pyocd support for semihosting is buggy.  So I switched to using the builtin platformio support for the stlink adapter which worked much better.
-; However the built in openocd version in platformio has buggy support for TCP to semihosting. 
-;
-; So I'm now trying the external openocd - but the openocd scripts for nrf52.cfg assume you are using a DAP adapter not an STLINK adapter.
-; In theory I could change those scripts.  But for now I'm trying going back to a DAP adapter but with the external openocd.
-
-upload_protocol = stlink
-; eventually use platformio/tool-pyocd@^2.3600.0 instad
-;upload_protocol = custom
-;upload_command = pyocd flash -t nrf52840 $UPLOADERFLAGS $SOURCE
\ No newline at end of file
+  ${nrf52840_base.lib_deps}
\ No newline at end of file
diff --git a/variants/rak_wismeshtag/variant.h b/variants/rak_wismeshtag/variant.h
index f87592680..dd82b76a1 100644
--- a/variants/rak_wismeshtag/variant.h
+++ b/variants/rak_wismeshtag/variant.h
@@ -218,11 +218,6 @@ SO GPIO 39/TXEN MAY NOT BE DEFINED FOR SUCCESSFUL OPERATION OF THE SX1262 - TG
 #define GPS_RX_PIN PIN_SERIAL1_RX
 #define GPS_TX_PIN PIN_SERIAL1_TX
 
-// Define pin to enable GPS toggle (set GPIO to LOW) via user button triple press
-
-// RAK12002 RTC Module
-#define RV3028_RTC (uint8_t)0b1010010
-
 // RAK WISMESHTAG
 #define PIN_BUZZER 21