SD software SPI control

src/FSCommon.cpp

@@ -12,7 +12,8 @@
 #include "SPILock.h"
 #include "configuration.h"
 
-#ifdef HAS_SDCARD
+// Software SPI is used by MUI so disable SD card here until it's also implemented
+#if defined(HAS_SDCARD) && !defined(SDCARD_USE_SOFT_SPI)
 #include <SD.h>
 #include <SPI.h>
 
@@ -306,7 +307,7 @@ void fsInit()
  */
 void setupSDCard()
 {
-#ifdef HAS_SDCARD
+#if defined(HAS_SDCARD) && !defined(SDCARD_USE_SOFT_SPI)
     concurrency::LockGuard g(spiLock);
     SDHandler.begin(SPI_SCK, SPI_MISO, SPI_MOSI);
     if (!SD.begin(SDCARD_CS, SDHandler, SD_SPI_FREQUENCY)) {

variants/elecrow_panel/pins_arduino.h

@@ -17,6 +17,14 @@ static const uint8_t MOSI = 48;
 static const uint8_t MISO = 47;
 static const uint8_t SCK = 41;
 
+#ifndef CROW_SELECT
+static const uint8_t SPI_MOSI = 6;
+static const uint8_t SPI_SCK = 5;
+static const uint8_t SPI_MISO = 4;
+static const uint8_t SPI_CS = 7; // SD does not support -1
+static const uint8_t SDCARD_CS = SPI_CS;
+#endif
+
 static const uint8_t A0 = 1;
 static const uint8_t A1 = 2;
 static const uint8_t A2 = 3;

variants/elecrow_panel/platformio.ini

@@ -3,7 +3,6 @@
 extends = esp32s3_base
 board = crowpanel
 board_check = true
-board_level = extra
 upload_protocol = esptool
 
 build_flags = ${esp32s3_base.build_flags}
@@ -83,8 +82,10 @@ build_flags =
   ${crowpanel_base_tft.build_flags}
   -D TFT_HEIGHT=320 ; needed in variant.h
   -D HAS_SDCARD
+  -D SDCARD_USE_SOFT_SPI
+  -D SPI_DRIVER_SELECT=2
   -D USE_I2S_BUZZER
-;  -D INPUTDRIVER_BUTTON_TYPE=0
+  -D INPUTDRIVER_BUTTON_TYPE=0
   -D LGFX_DRIVER_TEMPLATE
   -D LGFX_DRIVER=LGFX_GENERIC
   -D GFX_DRIVER_INC=\"graphics/LGFX/LGFX_GENERIC.h\"
@@ -128,8 +129,10 @@ build_flags =
   ${crowpanel_base_tft.build_flags}
   -D TFT_HEIGHT=480 ; needed in variant.h
   -D HAS_SDCARD
+  -D SDCARD_USE_SOFT_SPI
+  -D SPI_DRIVER_SELECT=2
   -D USE_I2S_BUZZER
-;  -D INPUTDRIVER_BUTTON_TYPE=0
+  -D INPUTDRIVER_BUTTON_TYPE=0
   -D LV_CACHE_DEF_SIZE=2097152
   -D LGFX_DRIVER_TEMPLATE
   -D LGFX_DRIVER=LGFX_GENERIC
@@ -159,6 +162,7 @@ build_flags =
 # 4.3 inch 800x480 IPS ST7265
 [env:elecrow-43]
 extends = crowpanel_base
+board_level = extra
 
 build_flags =
   ${crowpanel_base.build_flags}
@@ -172,6 +176,7 @@ build_flags =
 # 5 inch 800x480 IPS ST7262
 [env:elecrow-50]
 extends = crowpanel_base
+board_level = extra
 
 build_flags =
   ${crowpanel_base.build_flags}
@@ -185,6 +190,7 @@ build_flags =
 # 7 inch 800x480 IPS SC7277
 [env:elecrow-70]
 extends = crowpanel_base
+board_level = extra
 
 build_flags =
   ${crowpanel_base.build_flags}
@@ -197,6 +203,7 @@ build_flags =
 
 [env:elecrow-70-tft]
 extends = crowpanel_base_tft
+board_level = extra
 
 build_flags =
   ${crowpanel_base_tft.build_flags}

variants/elecrow_panel/variant.h

@@ -135,18 +135,6 @@
 #define GPS_RX_PIN 18
 #define GPS_TX_PIN 17
 
-#if TFT_HEIGHT == 320 || TFT_HEIGHT == 480
-// SDCard 2.4 - 3.5 TFT
-// #define HAS_SDCARD -> must be defined in platformio.ini
-#define SPI_SCK 5
-#define SPI_MISO 4
-#define SPI_MOSI 6
-#define SDCARD_CS 7 // SD does not support -1
-#else
-// SDCard (from 4.3 only if LoRa is disabled)
-
-#endif
-
 // Extension Slot Layout, viewed from above (2.4-3.5)
 // DIO1/IO1 o   o IO2/NRESET
 // SCK/IO10 o   o IO16/NC