trunk'd

.trunk/trunk.yaml

@@ -9,14 +9,14 @@ plugins:
 lint:
   enabled:
     - prettier@3.5.3
-    - trufflehog@3.88.16
+    - trufflehog@3.88.17
     - yamllint@1.36.0
     - bandit@1.8.3
-    - checkov@3.2.384
+    - checkov@3.2.386
     - terrascan@1.19.9
     - trivy@0.60.0
     - taplo@0.9.3
-    - ruff@0.9.10
+    - ruff@0.10.0
     - isort@6.0.1
     - markdownlint@0.44.0
     - oxipng@9.1.4

src/modules/CannedMessageModule.cpp

@@ -1058,8 +1058,8 @@ void CannedMessageModule::drawFrame(OLEDDisplay *display, OLEDDisplayUiState *st
     } else if (cannedMessageModule->runState == CANNED_MESSAGE_RUN_STATE_FREETEXT) {
         requestFocus(); // Tell Screen::setFrames to move to our module's frame
 #if defined(USE_EINK) && defined(USE_EINK_DYNAMICDISPLAY)
-        EInkDynamicDisplay* einkDisplay = static_cast<EInkDynamicDisplay*>(display);
-        einkDisplay->enableUnlimitedFastMode();  // Enable unlimited fast refresh while typing
+        EInkDynamicDisplay *einkDisplay = static_cast<EInkDynamicDisplay *>(display);
+        einkDisplay->enableUnlimitedFastMode(); // Enable unlimited fast refresh while typing
 #endif
 
 #if defined(USE_VIRTUAL_KEYBOARD)

variants/seeed_xiao_nrf52840_kit/variant.cpp

@@ -1,8 +1,8 @@
 #include "variant.h"
+#include "configuration.h"
 #include "nrf.h"
 #include "wiring_constants.h"
 #include "wiring_digital.h"
-#include "configuration.h"
 #include <map>
 #include <memory>
 #include <stddef.h>
@@ -58,8 +58,6 @@ const uint32_t g_ADigitalPinMap[] = {
     31, // D32 is P0.10 (VBAT)
 };
 
-
-
 /*
   Copyright (c) 2014-2015 Arduino LLC.  All right reserved.
   Copyright (c) 2016 Sandeep Mistry All right reserved.
@@ -80,7 +78,6 @@ const uint32_t g_ADigitalPinMap[] = {
   Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
 */
 
-
 void initVariant()
 {
     // LED1 & LED2

variants/seeed_xiao_nrf52840_kit/variant.h

@@ -43,7 +43,6 @@ extern "C" {
  * Buttons
  */
 
-
 // Digital PINs
 #define D0 (0ul)
 #define D1 (1ul)
@@ -86,7 +85,6 @@ static const uint8_t A4 = PIN_A4;
 static const uint8_t A5 = PIN_A5;
 #define ADC_RESOLUTION 12
 
-
 #define PIN_SERIAL2_RX (-1)
 #define PIN_SERIAL2_TX (-1)
 
@@ -99,7 +97,6 @@ static const uint8_t A5 = PIN_A5;
 #define PIN_SPI_MOSI (10)
 #define PIN_SPI_SCK (8)
 
-
 static const uint8_t SS = D4;
 static const uint8_t MOSI = PIN_SPI_MOSI;
 static const uint8_t MISO = PIN_SPI_MISO;
@@ -117,25 +114,23 @@ static const uint8_t SCK = PIN_SPI_SCK;
 
 #define SX126X_TXEN RADIOLIB_NC
 
-
 #define SX126X_RXEN D4
-#define SX126X_DIO2_AS_RF_SWITCH        // DIO2 is used to control the RF switch really necessary!!!
+#define SX126X_DIO2_AS_RF_SWITCH // DIO2 is used to control the RF switch really necessary!!!
 #define SX126X_DIO3_TCXO_VOLTAGE 1.8
 
 /*
  * Wire Interfaces
  */
 
-#define I2C_NO_RESCAN              // I2C is a bit finicky, don't scan too much
+#define I2C_NO_RESCAN           // I2C is a bit finicky, don't scan too much
 #define WIRE_INTERFACES_COUNT 1 // 2
 
-#define PIN_WIRE_SDA (24)           //change to use the correct pins if needed
-#define PIN_WIRE_SCL (25)           //change to use the correct pins if needed
+#define PIN_WIRE_SDA (24) // change to use the correct pins if needed
+#define PIN_WIRE_SCL (25) // change to use the correct pins if needed
 
 static const uint8_t SDA = PIN_WIRE_SDA;
 static const uint8_t SCL = PIN_WIRE_SCL;
 
-
 // GPS L76KB
 #define GPS_L76K
 #ifdef GPS_L76K
@@ -149,8 +144,6 @@ static const uint8_t SCL = PIN_WIRE_SCL;
 #define PIN_GPS_STANDBY D0
 #endif
 
-
-
 // Battery
 
 #define BAT_READ                                                                                                                 \