diff --git a/lib/device-ui b/lib/device-ui
deleted file mode 160000
index 6b760f537..000000000
--- a/lib/device-ui
+++ /dev/null
@@ -1 +0,0 @@
-Subproject commit 6b760f5373b91de1d8234922a446f7232d5247d0
diff --git a/variants/heltec_capsule_sensor_v3/platformio.ini b/variants/heltec_capsule_sensor_v3/platformio.ini
deleted file mode 100644
index b5ffb65c2..000000000
--- a/variants/heltec_capsule_sensor_v3/platformio.ini
+++ /dev/null
@@ -1,10 +0,0 @@
-[env:heltec_capsule_sensor_v3]
-extends = esp32s3_base
-board = heltec_wifi_lora_32_V3
-board_check = true
-
-build_flags = 
-  ${esp32s3_base.build_flags} -I variants/heltec_capsule_sensor_v3
-  -D HELTEC_CAPSULE_SENSOR_V3
-  -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
-  ;-D DEBUG_DISABLED ; uncomment this line to disable DEBUG output
\ No newline at end of file
diff --git a/variants/heltec_capsule_sensor_v3/variant.h b/variants/heltec_capsule_sensor_v3/variant.h
deleted file mode 100644
index 415de0559..000000000
--- a/variants/heltec_capsule_sensor_v3/variant.h
+++ /dev/null
@@ -1,53 +0,0 @@
-#define LED_PIN 33
-#define LED_PIN2 34
-#define EXT_PWR_DETECT 35
-
-#define BUTTON_PIN 18
-
-#define BATTERY_PIN 7 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
-#define ADC_CHANNEL ADC1_GPIO7_CHANNEL
-#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider
-#define ADC_MULTIPLIER (4.9 * 1.045)
-#define ADC_CTRL 36 // active HIGH, powers the voltage divider. Only on 1.1
-#define ADC_CTRL_ENABLED HIGH
-
-#undef GPS_RX_PIN
-#undef GPS_TX_PIN
-#define GPS_RX_PIN 5
-#define GPS_TX_PIN 4
-#define PIN_GPS_RESET 3
-#define GPS_RESET_MODE LOW
-#define PIN_GPS_PPS 1
-#define PIN_GPS_EN 21
-#define GPS_EN_ACTIVE HIGH
-
-#define USE_SX1262
-#define LORA_DIO0 -1 // a No connect on the SX1262 module
-#define LORA_RESET 12
-#define LORA_DIO1 14 // SX1262 IRQ
-#define LORA_DIO2 13 // SX1262 BUSY
-#define LORA_DIO3    // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
-
-#define LORA_SCK 9
-#define LORA_MISO 11
-#define LORA_MOSI 10
-#define LORA_CS 8
-
-#define SX126X_CS LORA_CS
-#define SX126X_DIO1 LORA_DIO1
-#define SX126X_BUSY LORA_DIO2
-#define SX126X_RESET LORA_RESET
-
-#define SX126X_DIO2_AS_RF_SWITCH
-#define SX126X_DIO3_TCXO_VOLTAGE 1.8
-
-#define I2C_SDA 1
-#define I2C_SCL 2
-#define HAS_SCREEN 0
-#define SENSOR_POWER_CTRL_PIN 21
-#define SENSOR_POWER_ON 1
-
-#define PERIPHERAL_WARMUP_MS 100
-#define SENSOR_GPS_CONFLICT
-
-#define ESP32S3_WAKE_TYPE ESP_EXT1_WAKEUP_ANY_HIGH
\ No newline at end of file