diff --git a/src/Power.cpp b/src/Power.cpp
index f9b04dfd5..02a07e620 100644
--- a/src/Power.cpp
+++ b/src/Power.cpp
@@ -360,7 +360,12 @@ class AnalogBatteryLevel : public HasBatteryLevel
     /**
      * return true if there is a battery installed in this unit
      */
+    // if we have a integrated device with a battery, we can assume that the battery is always connected
+#ifdef BATTERY_IMMUTABLE
+    virtual bool isBatteryConnect() override { return true; }
+#else
     virtual bool isBatteryConnect() override { return getBatteryPercent() != -1; }
+#endif
 
     /// If we see a battery voltage higher than physics allows - assume charger is pumping
     /// in power
diff --git a/src/configuration.h b/src/configuration.h
index 66070eb40..cb2326470 100644
--- a/src/configuration.h
+++ b/src/configuration.h
@@ -136,6 +136,7 @@ along with this program.  If not, see <http://www.gnu.org/licenses/>.
 #define LPS22HB_ADDR_ALT 0x5D
 #define SHT31_4x_ADDR 0x44
 #define PMSA0031_ADDR 0x12
+#define QMA6100P_ADDR 0x12
 #define AHT10_ADDR 0x38
 #define RCWL9620_ADDR 0x57
 #define VEML7700_ADDR 0x10
diff --git a/src/detect/ScanI2C.cpp b/src/detect/ScanI2C.cpp
index 41ba8257e..4caa0f730 100644
--- a/src/detect/ScanI2C.cpp
+++ b/src/detect/ScanI2C.cpp
@@ -37,8 +37,8 @@ ScanI2C::FoundDevice ScanI2C::firstKeyboard() const
 
 ScanI2C::FoundDevice ScanI2C::firstAccelerometer() const
 {
-    ScanI2C::DeviceType types[] = {MPU6050, LIS3DH, BMA423, LSM6DS3, BMX160, STK8BAXX, ICM20948};
-    return firstOfOrNONE(7, types);
+    ScanI2C::DeviceType types[] = {MPU6050, LIS3DH, BMA423, LSM6DS3, BMX160, STK8BAXX, ICM20948, QMA6100P};
+    return firstOfOrNONE(8, types);
 }
 
 ScanI2C::FoundDevice ScanI2C::find(ScanI2C::DeviceType) const
diff --git a/src/detect/ScanI2C.h b/src/detect/ScanI2C.h
index b2c482c98..8591b8433 100644
--- a/src/detect/ScanI2C.h
+++ b/src/detect/ScanI2C.h
@@ -39,6 +39,7 @@ class ScanI2C
         QMC5883L,
         HMC5883L,
         PMSA0031,
+        QMA6100P,
         MPU6050,
         LIS3DH,
         BMA423,
diff --git a/src/detect/ScanI2CTwoWire.cpp b/src/detect/ScanI2CTwoWire.cpp
index 6cb6ba09a..d39c9899c 100644
--- a/src/detect/ScanI2CTwoWire.cpp
+++ b/src/detect/ScanI2CTwoWire.cpp
@@ -173,7 +173,16 @@ void ScanI2CTwoWire::scanPort(I2CPort port, uint8_t *address, uint8_t asize)
     }
 #endif
 
-    for (addr.address = 1; addr.address < 127; addr.address++) {
+    // We only need to scan 112 addresses, the rest is reserved for special purposes
+    // 0x00 General Call
+    // 0x01 CBUS addresses
+    // 0x02 Reserved for different bus formats
+    // 0x03 Reserved for future purposes
+    // 0x04-0x07 High Speed Master Code
+    // 0x78-0x7B 10-bit slave addressing
+    // 0x7C-0x7F Reserved for future purposes
+
+    for (addr.address = 8; addr.address < 120; addr.address++) {
         if (asize != 0) {
             if (!in_array(address, asize, addr.address))
                 continue;
@@ -395,7 +404,11 @@ void ScanI2CTwoWire::scanPort(I2CPort port, uint8_t *address, uint8_t asize)
 
                 SCAN_SIMPLE_CASE(QMC5883L_ADDR, QMC5883L, "QMC5883L Highrate 3-Axis magnetic sensor found")
                 SCAN_SIMPLE_CASE(HMC5883L_ADDR, HMC5883L, "HMC5883L 3-Axis digital compass found")
+#ifdef HAS_QMA6100P
+                SCAN_SIMPLE_CASE(QMA6100P_ADDR, QMA6100P, "QMA6100P accelerometer found")
+#else
                 SCAN_SIMPLE_CASE(PMSA0031_ADDR, PMSA0031, "PMSA0031 air quality sensor found")
+#endif
                 SCAN_SIMPLE_CASE(BMA423_ADDR, BMA423, "BMA423 accelerometer found");
                 SCAN_SIMPLE_CASE(LSM6DS3_ADDR, LSM6DS3, "LSM6DS3 accelerometer found at address 0x%x", (uint8_t)addr.address);
                 SCAN_SIMPLE_CASE(TCA9535_ADDR, TCA9535, "TCA9535 I2C expander found");
diff --git a/src/input/cardKbI2cImpl.cpp b/src/input/cardKbI2cImpl.cpp
index 7ad2eb2ac..c1f35ba3c 100644
--- a/src/input/cardKbI2cImpl.cpp
+++ b/src/input/cardKbI2cImpl.cpp
@@ -9,7 +9,7 @@ CardKbI2cImpl::CardKbI2cImpl() : KbI2cBase("cardKB") {}
 
 void CardKbI2cImpl::init()
 {
-#if !MESHTASTIC_EXCLUDE_I2C && !defined(ARCH_PORTDUINO)
+#if !MESHTASTIC_EXCLUDE_I2C && !defined(ARCH_PORTDUINO) && !defined(I2C_NO_RESCAN)
     if (cardkb_found.address == 0x00) {
         LOG_DEBUG("Rescanning for I2C keyboard");
         uint8_t i2caddr_scan[] = {CARDKB_ADDR, TDECK_KB_ADDR, BBQ10_KB_ADDR, MPR121_KB_ADDR};
@@ -49,7 +49,7 @@ void CardKbI2cImpl::init()
                 kb_model = 0x00;
             }
         }
-        LOG_DEBUG("Keyboard Type: 0x%02x Model: 0x%02x Address: 0x%02x\n", kb_info.type, kb_model, cardkb_found.address);
+        LOG_DEBUG("Keyboard Type: 0x%02x Model: 0x%02x Address: 0x%02x", kb_info.type, kb_model, cardkb_found.address);
         if (cardkb_found.address == 0x00) {
             disable();
             return;
diff --git a/src/modules/Telemetry/AirQualityTelemetry.cpp b/src/modules/Telemetry/AirQualityTelemetry.cpp
index 594707537..5f7fe5dac 100644
--- a/src/modules/Telemetry/AirQualityTelemetry.cpp
+++ b/src/modules/Telemetry/AirQualityTelemetry.cpp
@@ -35,6 +35,7 @@ int32_t AirQualityTelemetryModule::runOnce()
         if (moduleConfig.telemetry.air_quality_enabled) {
             LOG_INFO("Air quality Telemetry: Initializing");
             if (!aqi.begin_I2C()) {
+#ifndef I2C_NO_RESCAN
                 LOG_WARN("Could not establish i2c connection to AQI sensor. Rescanning...");
                 // rescan for late arriving sensors. AQI Module starts about 10 seconds into the boot so this is plenty.
                 uint8_t i2caddr_scan[] = {PMSA0031_ADDR};
@@ -51,6 +52,7 @@ int32_t AirQualityTelemetryModule::runOnce()
                         i2cScanner->fetchI2CBus(found.address);
                     return 1000;
                 }
+#endif
                 return disable();
             }
             return 1000;
diff --git a/src/motion/AccelerometerThread.h b/src/motion/AccelerometerThread.h
index b9ae926cf..e548b20c6 100755
--- a/src/motion/AccelerometerThread.h
+++ b/src/motion/AccelerometerThread.h
@@ -14,6 +14,9 @@
 #include "LSM6DS3Sensor.h"
 #include "MPU6050Sensor.h"
 #include "MotionSensor.h"
+#ifdef HAS_QMA6100P
+#include "QMA6100PSensor.h"
+#endif
 #include "STK8XXXSensor.h"
 
 extern ScanI2C::DeviceAddress accelerometer_found;
@@ -97,6 +100,11 @@ class AccelerometerThread : public concurrency::OSThread
         case ScanI2C::DeviceType::ICM20948:
             sensor = new ICM20948Sensor(device);
             break;
+#ifdef HAS_QMA6100P
+        case ScanI2C::DeviceType::QMA6100P:
+            sensor = new QMA6100PSensor(device);
+            break;
+#endif
         default:
             disable();
             return;
diff --git a/src/motion/QMA6100PSensor.cpp b/src/motion/QMA6100PSensor.cpp
new file mode 100644
index 000000000..237df0b65
--- /dev/null
+++ b/src/motion/QMA6100PSensor.cpp
@@ -0,0 +1,183 @@
+#include "QMA6100PSensor.h"
+
+#if !defined(ARCH_PORTDUINO) && !defined(ARCH_STM32WL) && !MESHTASTIC_EXCLUDE_I2C && HAS_QMA6100P
+
+// Flag when an interrupt has been detected
+volatile static bool QMA6100P_IRQ = false;
+
+// Interrupt service routine
+void QMA6100PSetInterrupt()
+{
+    QMA6100P_IRQ = true;
+}
+
+QMA6100PSensor::QMA6100PSensor(ScanI2C::FoundDevice foundDevice) : MotionSensor::MotionSensor(foundDevice) {}
+
+bool QMA6100PSensor::init()
+{
+    // Initialise the sensor
+    sensor = QMA6100PSingleton::GetInstance();
+    if (!sensor->init(device))
+        return false;
+
+    // Enable simple Wake on Motion
+    return sensor->setWakeOnMotion();
+}
+
+#ifdef QMA_6100P_INT_PIN
+
+int32_t QMA6100PSensor::runOnce()
+{
+    // Wake on motion using hardware interrupts - this is the most efficient way to check for motion
+    if (QMA6100P_IRQ) {
+        QMA6100P_IRQ = false;
+        wakeScreen();
+    }
+    return MOTION_SENSOR_CHECK_INTERVAL_MS;
+}
+
+#else
+
+int32_t QMA6100PSensor::runOnce()
+{
+    // Wake on motion using polling  - this is not as efficient as using hardware interrupt pin (see above)
+
+    uint8_t tempVal;
+    if (!sensor->readRegisterRegion(SFE_QMA6100P_INT_ST0, &tempVal, 1)) {
+        LOG_DEBUG("QMA6100PSensor::isWakeOnMotion failed to read interrupts");
+        return MOTION_SENSOR_CHECK_INTERVAL_MS;
+    }
+
+    if ((tempVal & 7) != 0) {
+        // Wake up!
+        wakeScreen();
+    }
+    return MOTION_SENSOR_CHECK_INTERVAL_MS;
+}
+
+#endif
+
+// ----------------------------------------------------------------------
+// QMA6100PSingleton
+// ----------------------------------------------------------------------
+
+// Get a singleton wrapper for an Sparkfun QMA_6100P_I2C
+QMA6100PSingleton *QMA6100PSingleton::GetInstance()
+{
+    if (pinstance == nullptr) {
+        pinstance = new QMA6100PSingleton();
+    }
+    return pinstance;
+}
+
+QMA6100PSingleton::QMA6100PSingleton() {}
+
+QMA6100PSingleton::~QMA6100PSingleton() {}
+
+QMA6100PSingleton *QMA6100PSingleton::pinstance{nullptr};
+
+// Initialise the QMA6100P Sensor
+bool QMA6100PSingleton::init(ScanI2C::FoundDevice device)
+{
+
+// startup
+#ifdef Wire1
+    bool status = begin(device.address.address, device.address.port == ScanI2C::I2CPort::WIRE1 ? &Wire1 : &Wire);
+#else
+    // check chip id
+    bool status = begin(device.address.address, &Wire);
+#endif
+    if (status != true) {
+        LOG_WARN("QMA6100PSensor::init begin failed\n");
+        return false;
+    }
+    delay(20);
+    // SW reset to make sure the device starts in a known state
+    if (softwareReset() != true) {
+        LOG_WARN("QMA6100PSensor::init reset failed\n");
+        return false;
+    }
+    delay(20);
+    // Set range
+    if (!setRange(QMA_6100P_MPU_ACCEL_SCALE)) {
+        LOG_WARN("QMA6100PSensor::init range failed");
+        return false;
+    }
+    // set active mode
+    if (!enableAccel()) {
+        LOG_WARN("ERROR :QMA6100PSensor::active mode set failed");
+    }
+    // set calibrateoffsets
+    if (!calibrateOffsets()) {
+        LOG_WARN("ERROR :QMA6100PSensor:: calibration failed");
+    }
+#ifdef QMA_6100P_INT_PIN
+
+    // Active low & Open Drain
+    uint8_t tempVal;
+    if (!readRegisterRegion(SFE_QMA6100P_INTPINT_CONF, &tempVal, 1)) {
+        LOG_WARN("QMA6100PSensor::init failed to read interrupt pin config");
+        return false;
+    }
+
+    tempVal |= 0b00000010; // Active low & Open Drain
+
+    if (!writeRegisterByte(SFE_QMA6100P_INTPINT_CONF, tempVal)) {
+        LOG_WARN("QMA6100PSensor::init failed to write interrupt pin config");
+        return false;
+    }
+
+    // Latch until cleared, all reads clear the latch
+    if (!readRegisterRegion(SFE_QMA6100P_INT_CFG, &tempVal, 1)) {
+        LOG_WARN("QMA6100PSensor::init failed to read interrupt config");
+        return false;
+    }
+
+    tempVal |= 0b10000001; // Latch until cleared, INT_RD_CLR1
+
+    if (!writeRegisterByte(SFE_QMA6100P_INT_CFG, tempVal)) {
+        LOG_WARN("QMA6100PSensor::init failed to write interrupt config");
+        return false;
+    }
+    // Set up an interrupt pin with an internal pullup for active low
+    pinMode(QMA_6100P_INT_PIN, INPUT_PULLUP);
+
+    // Set up an interrupt service routine
+    attachInterrupt(QMA_6100P_INT_PIN, QMA6100PSetInterrupt, FALLING);
+
+#endif
+    return true;
+}
+
+bool QMA6100PSingleton::setWakeOnMotion()
+{
+    // Enable 'Any Motion' interrupt
+    if (!writeRegisterByte(SFE_QMA6100P_INT_EN2, 0b00000111)) {
+        LOG_WARN("QMA6100PSingleton::setWakeOnMotion failed to write interrupt enable");
+        return false;
+    }
+
+    // Set 'Significant Motion' interrupt map to INT1
+    uint8_t tempVal;
+
+    if (!readRegisterRegion(SFE_QMA6100P_INT_MAP1, &tempVal, 1)) {
+        LOG_WARN("QMA6100PSingleton::setWakeOnMotion failed to read interrupt map");
+        return false;
+    }
+
+    sfe_qma6100p_int_map1_bitfield_t int_map1;
+    int_map1.all = tempVal;
+    int_map1.bits.int1_any_mot = 1; // any motion interrupt to INT1
+    tempVal = int_map1.all;
+
+    if (!writeRegisterByte(SFE_QMA6100P_INT_MAP1, tempVal)) {
+        LOG_WARN("QMA6100PSingleton::setWakeOnMotion failed to write interrupt map");
+        return false;
+    }
+
+    // Clear any current interrupts
+    QMA6100P_IRQ = false;
+    return true;
+}
+
+#endif
\ No newline at end of file
diff --git a/src/motion/QMA6100PSensor.h b/src/motion/QMA6100PSensor.h
new file mode 100644
index 000000000..986b0366d
--- /dev/null
+++ b/src/motion/QMA6100PSensor.h
@@ -0,0 +1,63 @@
+#pragma once
+#ifndef _QMA_6100P_SENSOR_H_
+#define _QMA_6100P_SENSOR_H_
+
+#include "MotionSensor.h"
+
+#if !defined(ARCH_PORTDUINO) && !defined(ARCH_STM32WL) && !MESHTASTIC_EXCLUDE_I2C && HAS_QMA6100P
+
+#include <QMA6100P.h>
+
+// Set the default accelerometer scale - gpm2, gpm4, gpm8, gpm16
+#ifndef QMA_6100P_MPU_ACCEL_SCALE
+#define QMA_6100P_MPU_ACCEL_SCALE SFE_QMA6100P_RANGE32G
+#endif
+
+// The I2C address of the Accelerometer (if found) from main.cpp
+extern ScanI2C::DeviceAddress accelerometer_found;
+
+// Singleton wrapper for the Sparkfun QMA_6100P_I2C class
+class QMA6100PSingleton : public QMA6100P
+{
+  private:
+    static QMA6100PSingleton *pinstance;
+
+  protected:
+    QMA6100PSingleton();
+    ~QMA6100PSingleton();
+
+  public:
+    // Create a singleton instance (not thread safe)
+    static QMA6100PSingleton *GetInstance();
+
+    // Singletons should not be cloneable.
+    QMA6100PSingleton(QMA6100PSingleton &other) = delete;
+
+    // Singletons should not be assignable.
+    void operator=(const QMA6100PSingleton &) = delete;
+
+    // Initialise the motion sensor singleton for normal operation
+    bool init(ScanI2C::FoundDevice device);
+
+    // Enable Wake on Motion interrupts (sensor must be initialised first)
+    bool setWakeOnMotion();
+};
+
+class QMA6100PSensor : public MotionSensor
+{
+  private:
+    QMA6100PSingleton *sensor = nullptr;
+
+  public:
+    explicit QMA6100PSensor(ScanI2C::FoundDevice foundDevice);
+
+    // Initialise the motion sensor
+    virtual bool init() override;
+
+    // Called each time our sensor gets a chance to run
+    virtual int32_t runOnce() override;
+};
+
+#endif
+
+#endif
\ No newline at end of file
diff --git a/src/mqtt/MQTT.cpp b/src/mqtt/MQTT.cpp
index 2a2018395..39d554100 100644
--- a/src/mqtt/MQTT.cpp
+++ b/src/mqtt/MQTT.cpp
@@ -717,7 +717,7 @@ bool MQTT::isPrivateIpAddress(const char address[])
     // Even if it's not a valid IP address, we will know it's not a domain.
     bool hasColon = false;
     int numDots = 0;
-    for (int i = 0; i < length; i++) {
+    for (size_t i = 0; i < length; i++) {
         if (!isdigit(address[i]) && address[i] != '.' && address[i] != ':') {
             return false;
         }
diff --git a/variants/tracker-t1000-e/platformio.ini b/variants/tracker-t1000-e/platformio.ini
index dfc72f3f0..075811610 100644
--- a/variants/tracker-t1000-e/platformio.ini
+++ b/variants/tracker-t1000-e/platformio.ini
@@ -1,16 +1,14 @@
-; tracker-t1000-e  v0.9.1
 [env:tracker-t1000-e]
 extends = nrf52840_base
 board = tracker-t1000-e
-; board_level = extra
-; platform = https://github.com/maxgerhardt/platform-nordicnrf52#cac6fcf943a41accd2aeb4f3659ae297a73f422e
 build_flags = ${nrf52840_base.build_flags} -Ivariants/tracker-t1000-e -Isrc/platform/nrf52/softdevice -Isrc/platform/nrf52/softdevice/nrf52 -DTRACKER_T1000_E
   -L "${platformio.libdeps_dir}/${this.__env__}/bsec2/src/cortex-m4/fpv4-sp-d16-hard"
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
+  -DGPS_POWER_TOGGLE
 board_build.ldscript = src/platform/nrf52/nrf52840_s140_v7.ld
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/tracker-t1000-e>
 lib_deps = 
   ${nrf52840_base.lib_deps}
+  https://github.com/meshtastic/QMA6100P_Arduino_Library.git#14c900b8b2e4feaac5007a7e41e0c1b7f0841136
 debug_tool = jlink
 ; If not set we will default to uploading over serial (first it forces bootloader entry by talking 1200bps to cdcacm)
 upload_protocol = nrfutil
diff --git a/variants/tracker-t1000-e/variant.cpp b/variants/tracker-t1000-e/variant.cpp
index 85e0c44f3..8096705d0 100644
--- a/variants/tracker-t1000-e/variant.cpp
+++ b/variants/tracker-t1000-e/variant.cpp
@@ -40,7 +40,7 @@ void initVariant()
     digitalWrite(PIN_3V3_EN, HIGH);
 
     pinMode(PIN_3V3_ACC_EN, OUTPUT);
-    digitalWrite(PIN_3V3_ACC_EN, LOW);
+    digitalWrite(PIN_3V3_ACC_EN, HIGH);
 
     pinMode(BUZZER_EN_PIN, OUTPUT);
     digitalWrite(BUZZER_EN_PIN, HIGH);
diff --git a/variants/tracker-t1000-e/variant.h b/variants/tracker-t1000-e/variant.h
index b8eb59b31..6a1f99600 100644
--- a/variants/tracker-t1000-e/variant.h
+++ b/variants/tracker-t1000-e/variant.h
@@ -52,7 +52,7 @@ extern "C" {
 #define LED_BLUE -1    // Actually green
 #define LED_STATE_ON 1 // State when LED is lit
 
-#define BUTTON_PIN (0 + 6) // P0.6
+#define BUTTON_PIN (0 + 6) // P0.06
 #define BUTTON_ACTIVE_LOW false
 #define BUTTON_ACTIVE_PULLUP false
 #define BUTTON_SENSE_TYPE 0x6
@@ -61,9 +61,11 @@ extern "C" {
 
 #define WIRE_INTERFACES_COUNT 1
 
-// unused pins
-#define PIN_WIRE_SDA (0 + 9)  // P0.26
-#define PIN_WIRE_SCL (0 + 10) // P0.27
+#define PIN_WIRE_SDA (0 + 26)      // P0.26
+#define PIN_WIRE_SCL (0 + 27)      // P0.27
+#define I2C_NO_RESCAN              // I2C is a bit finicky, don't scan too much
+#define HAS_QMA6100P               // very rare beast, only on this board.
+#define QMA_6100P_INT_PIN (32 + 2) // P1.02
 
 /*
  * Serial interfaces
@@ -116,14 +118,22 @@ extern "C" {
 #define PIN_GPS_RESET (32 + 15) // P1.15
 #define GPS_RESET_MODE HIGH
 
-#define GPS_VRTC_EN (0 + 8)      // P0.8, awlays high
-#define GPS_SLEEP_INT (32 + 12)  // P1.12, awlays high
+#define GPS_VRTC_EN (0 + 8)      // P0.8, always high
+#define GPS_SLEEP_INT (32 + 12)  // P1.12, always high
 #define GPS_RTC_INT (0 + 15)     // P0.15, normal is LOW, wake by HIGH
-#define GPS_RESETB_OUT (32 + 14) // P1.14, awlays input pull_up
+#define GPS_RESETB_OUT (32 + 14) // P1.14, always input pull_up
 
 #define GPS_FIX_HOLD_TIME 15000 // ms
-#define BATTERY_PIN 2
+#define BATTERY_PIN 2           // P0.02/AIN0, BAT_ADC
+#define BATTERY_IMMUTABLE
 #define ADC_MULTIPLIER (2.0F)
+// P0.04/AIN2 is VCC_ADC, P0.05/AIN3 is CHARGER_DET, P1.03 is CHARGE_STA, P1.04 is CHARGE_DONE
+
+#define EXT_CHRG_DETECT (32 + 3) // P1.03
+#define EXT_CHRG_DETECT_VALUE LOW
+// #define EXT_IS_CHRGD (32 + 4)  // P1.04
+// #define EXT_IS_CHRGD_VALUE LOW
+#define EXT_PWR_DETECT (0 + 5) // P0.05
 
 #define ADC_RESOLUTION 14
 #define BATTERY_SENSE_RESOLUTION_BITS 12
@@ -133,13 +143,13 @@ extern "C" {
 #define VBAT_AR_INTERNAL AR_INTERNAL_3_0
 
 // Buzzer
-#define BUZZER_EN_PIN (32 + 5) // P1.05, awlays high
+#define BUZZER_EN_PIN (32 + 5) // P1.05, always high
 #define PIN_BUZZER (0 + 25)    // P0.25, pwm output
 
 #define T1000X_SENSOR_EN
 #define T1000X_VCC_PIN (0 + 4)  // P0.4
-#define T1000X_NTC_PIN (0 + 31) // P0.31
-#define T1000X_LUX_PIN (0 + 29) // P0.29
+#define T1000X_NTC_PIN (0 + 31) // P0.31/AIN7
+#define T1000X_LUX_PIN (0 + 29) // P0.29/AIN5
 
 #ifdef __cplusplus
 }