diff --git a/src/detect/ScanI2CTwoWire.cpp b/src/detect/ScanI2CTwoWire.cpp
index 6d5408eeb..da2a57fee 100644
--- a/src/detect/ScanI2CTwoWire.cpp
+++ b/src/detect/ScanI2CTwoWire.cpp
@@ -378,7 +378,8 @@ void ScanI2CTwoWire::scanPort(I2CPort port, uint8_t *address, uint8_t asize)
             case SHT31_4x_ADDR:     // same as OPT3001_ADDR_ALT
             case SHT31_4x_ADDR_ALT: // same as OPT3001_ADDR
                 registerValue = getRegisterValue(ScanI2CTwoWire::RegisterLocation(addr, 0x89), 2);
-                if (registerValue == 0x11a2 || registerValue == 0x11da || registerValue == 0x11f3 || registerValue == 0xe9c || registerValue == 0xc8d) {
+                if (registerValue == 0x11a2 || registerValue == 0x11da || registerValue == 0x11f3 || registerValue == 0xe9c ||
+                    registerValue == 0xc8d) {
                     type = SHT4X;
                     logFoundDevice("SHT4X", (uint8_t)addr.address);
                 } else if (getRegisterValue(ScanI2CTwoWire::RegisterLocation(addr, 0x7E), 2) == 0x5449) {
diff --git a/src/gps/GPS.cpp b/src/gps/GPS.cpp
index 2cfa558ed..297ed3dfa 100644
--- a/src/gps/GPS.cpp
+++ b/src/gps/GPS.cpp
@@ -494,17 +494,6 @@ bool GPS::setup()
     if (!didSerialInit) {
         int msglen = 0;
         if (tx_gpio && gnssModel == GNSS_MODEL_UNKNOWN) {
-#ifdef TRACKER_T1000_E
-            // add power up/down strategy, improve ag3335 detection success
-            digitalWrite(PIN_GPS_EN, LOW);
-            delay(500);
-            digitalWrite(GPS_VRTC_EN, LOW);
-            delay(1000);
-            digitalWrite(GPS_VRTC_EN, HIGH);
-            delay(500);
-            digitalWrite(PIN_GPS_EN, HIGH);
-            delay(1000);
-#endif
             if (probeTries < GPS_PROBETRIES) {
                 gnssModel = probe(serialSpeeds[speedSelect]);
                 if (gnssModel == GNSS_MODEL_UNKNOWN) {
diff --git a/src/nimble/NimbleBluetooth.cpp b/src/nimble/NimbleBluetooth.cpp
index 0b3009d39..60165b2c0 100644
--- a/src/nimble/NimbleBluetooth.cpp
+++ b/src/nimble/NimbleBluetooth.cpp
@@ -17,6 +17,21 @@
 #include "PowerStatus.h"
 #endif
 
+#if defined(CONFIG_IDF_TARGET_ESP32S3) || defined(CONFIG_IDF_TARGET_ESP32C6)
+#if defined(CONFIG_NIMBLE_CPP_IDF)
+#include "host/ble_gap.h"
+#else
+#include "nimble/nimble/host/include/host/ble_gap.h"
+#endif
+
+namespace
+{
+constexpr uint16_t kPreferredBleMtu = 517;
+constexpr uint16_t kPreferredBleTxOctets = 251;
+constexpr uint16_t kPreferredBleTxTimeUs = (kPreferredBleTxOctets + 14) * 8;
+} // namespace
+#endif
+
 NimBLECharacteristic *fromNumCharacteristic;
 NimBLECharacteristic *BatteryCharacteristic;
 NimBLECharacteristic *logRadioCharacteristic;
@@ -212,6 +227,27 @@ class NimbleBluetoothServerCallback : public NimBLEServerCallbacks
     virtual void onConnect(NimBLEServer *pServer, NimBLEConnInfo &connInfo)
     {
         LOG_INFO("BLE incoming connection %s", connInfo.getAddress().toString().c_str());
+
+#if defined(CONFIG_IDF_TARGET_ESP32S3) || defined(CONFIG_IDF_TARGET_ESP32C6)
+        const uint16_t connHandle = connInfo.getConnHandle();
+        int phyResult =
+            ble_gap_set_prefered_le_phy(connHandle, BLE_GAP_LE_PHY_2M_MASK, BLE_GAP_LE_PHY_2M_MASK, BLE_GAP_LE_PHY_CODED_ANY);
+        if (phyResult == 0) {
+            LOG_INFO("BLE conn %u requested 2M PHY", connHandle);
+        } else {
+            LOG_WARN("Failed to prefer 2M PHY for conn %u, rc=%d", connHandle, phyResult);
+        }
+
+        int dataLenResult = ble_gap_set_data_len(connHandle, kPreferredBleTxOctets, kPreferredBleTxTimeUs);
+        if (dataLenResult == 0) {
+            LOG_INFO("BLE conn %u requested data length %u bytes", connHandle, kPreferredBleTxOctets);
+        } else {
+            LOG_WARN("Failed to raise data length for conn %u, rc=%d", connHandle, dataLenResult);
+        }
+
+        LOG_INFO("BLE conn %u initial MTU %u (target %u)", connHandle, connInfo.getMTU(), kPreferredBleMtu);
+        pServer->updateConnParams(connHandle, 6, 12, 0, 200);
+#endif
     }
 
     virtual void onDisconnect(NimBLEServer *pServer, NimBLEConnInfo &connInfo, int reason)
@@ -316,6 +352,30 @@ void NimbleBluetooth::setup()
     NimBLEDevice::init(getDeviceName());
     NimBLEDevice::setPower(ESP_PWR_LVL_P9);
 
+#if defined(CONFIG_IDF_TARGET_ESP32S3) || defined(CONFIG_IDF_TARGET_ESP32C6)
+    int mtuResult = NimBLEDevice::setMTU(kPreferredBleMtu);
+    if (mtuResult == 0) {
+        LOG_INFO("BLE MTU request set to %u", kPreferredBleMtu);
+    } else {
+        LOG_WARN("Unable to request MTU %u, rc=%d", kPreferredBleMtu, mtuResult);
+    }
+
+    int phyResult = ble_gap_set_prefered_default_le_phy(BLE_GAP_LE_PHY_2M_MASK, BLE_GAP_LE_PHY_2M_MASK);
+    if (phyResult == 0) {
+        LOG_INFO("BLE default PHY preference set to 2M");
+    } else {
+        LOG_WARN("Failed to prefer 2M PHY by default, rc=%d", phyResult);
+    }
+
+    int dataLenResult = ble_gap_write_sugg_def_data_len(kPreferredBleTxOctets, kPreferredBleTxTimeUs);
+    if (dataLenResult == 0) {
+        LOG_INFO("BLE suggested data length set to %u bytes", kPreferredBleTxOctets);
+    } else {
+        LOG_WARN("Failed to raise suggested data length (%u/%u), rc=%d", kPreferredBleTxOctets, kPreferredBleTxTimeUs,
+                 dataLenResult);
+    }
+#endif
+
     if (config.bluetooth.mode != meshtastic_Config_BluetoothConfig_PairingMode_NO_PIN) {
         NimBLEDevice::setSecurityAuth(BLE_SM_PAIR_AUTHREQ_BOND | BLE_SM_PAIR_AUTHREQ_MITM | BLE_SM_PAIR_AUTHREQ_SC);
         NimBLEDevice::setSecurityInitKey(BLE_SM_PAIR_KEY_DIST_ENC | BLE_SM_PAIR_KEY_DIST_ID);
@@ -459,4 +519,4 @@ void clearNVS()
     ESP.restart();
 #endif
 }
-#endif
\ No newline at end of file
+#endif
diff --git a/variants/esp32/diy/hydra/variant.h b/variants/esp32/diy/hydra/variant.h
index 0d64c1b5e..e5c10e26b 100644
--- a/variants/esp32/diy/hydra/variant.h
+++ b/variants/esp32/diy/hydra/variant.h
@@ -6,7 +6,6 @@
 #define GPS_TX_PIN 15
 #define GPS_RX_PIN 12
 #define PIN_GPS_EN 4
-#define GPS_POWER_TOGGLE // Moved definition from platformio.ini to here
 
 #define BUTTON_PIN 39 // The middle button GPIO on the T-Beam
 // Note: On the ESP32 base version, gpio34-39 are input-only, and do not have internal pull-ups.
diff --git a/variants/esp32/heltec_v2.1/platformio.ini b/variants/esp32/heltec_v2.1/platformio.ini
index 763f9764c..4dcd9e583 100644
--- a/variants/esp32/heltec_v2.1/platformio.ini
+++ b/variants/esp32/heltec_v2.1/platformio.ini
@@ -7,4 +7,3 @@ build_flags =
   ${esp32_base.build_flags}
   -D HELTEC_V2_1
   -I variants/esp32/heltec_v2.1
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
diff --git a/variants/esp32/heltec_wsl_v2.1/platformio.ini b/variants/esp32/heltec_wsl_v2.1/platformio.ini
index eb44c88d2..6a77cf11b 100644
--- a/variants/esp32/heltec_wsl_v2.1/platformio.ini
+++ b/variants/esp32/heltec_wsl_v2.1/platformio.ini
@@ -6,4 +6,3 @@ build_flags =
   ${esp32_base.build_flags}
   -D PRIVATE_HW
   -I variants/esp32/heltec_wsl_v2.1
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
diff --git a/variants/esp32/tbeam/platformio.ini b/variants/esp32/tbeam/platformio.ini
index ea17751c6..e53f22d30 100644
--- a/variants/esp32/tbeam/platformio.ini
+++ b/variants/esp32/tbeam/platformio.ini
@@ -10,7 +10,6 @@ build_flags =
   ${esp32_base.build_flags}
   -D TBEAM_V10
   -I variants/esp32/tbeam
-  -DGPS_POWER_TOGGLE ; comment this line to disable double press function on the user button to turn off gps entirely.
   -DBOARD_HAS_PSRAM
   -mfix-esp32-psram-cache-issue
 upload_speed = 921600
diff --git a/variants/esp32/tlora_v2_1_16/platformio.ini b/variants/esp32/tlora_v2_1_16/platformio.ini
index bd85aa847..6967bb480 100644
--- a/variants/esp32/tlora_v2_1_16/platformio.ini
+++ b/variants/esp32/tlora_v2_1_16/platformio.ini
@@ -4,5 +4,4 @@ board = ttgo-lora32-v21
 board_check = true
 build_flags = 
   ${esp32_base.build_flags} -D TLORA_V2_1_16 -I variants/esp32/tlora_v2_1_16
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
 upload_speed = 115200
diff --git a/variants/esp32/tlora_v2_1_16_tcxo/platformio.ini b/variants/esp32/tlora_v2_1_16_tcxo/platformio.ini
index 9404faa02..a6b9d2254 100644
--- a/variants/esp32/tlora_v2_1_16_tcxo/platformio.ini
+++ b/variants/esp32/tlora_v2_1_16_tcxo/platformio.ini
@@ -6,6 +6,5 @@ build_flags =
   ${esp32_base.build_flags}
   -D TLORA_V2_1_16
   -I variants/esp32/tlora_v2_1_16
-  -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   -D LORA_TCXO_GPIO=33
 upload_speed = 115200
\ No newline at end of file
diff --git a/variants/esp32/tlora_v3_3_0_tcxo/platformio.ini b/variants/esp32/tlora_v3_3_0_tcxo/platformio.ini
index f1110386e..1258fd8b7 100644
--- a/variants/esp32/tlora_v3_3_0_tcxo/platformio.ini
+++ b/variants/esp32/tlora_v3_3_0_tcxo/platformio.ini
@@ -5,6 +5,5 @@ build_flags =
   ${esp32_base.build_flags}
   -D TLORA_V2_1_16
   -I variants/esp32/tlora_v2_1_16
-  -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   -D LORA_TCXO_GPIO=12
   -D BUTTON_PIN=0
\ No newline at end of file
diff --git a/variants/esp32s3/CDEBYTE_EoRa-S3/platformio.ini b/variants/esp32s3/CDEBYTE_EoRa-S3/platformio.ini
index dbd420f04..3fcfbf281 100644
--- a/variants/esp32s3/CDEBYTE_EoRa-S3/platformio.ini
+++ b/variants/esp32s3/CDEBYTE_EoRa-S3/platformio.ini
@@ -5,4 +5,3 @@ build_flags =
   ${esp32s3_base.build_flags}
   -D CDEBYTE_EORA_S3
   -I variants/esp32s3/CDEBYTE_EoRa-S3
-  -D GPS_POWER_TOGGLE
diff --git a/variants/esp32s3/crowpanel-esp32s3-5-epaper/platformio.ini b/variants/esp32s3/crowpanel-esp32s3-5-epaper/platformio.ini
index 49e84bf4f..eed21a412 100644
--- a/variants/esp32s3/crowpanel-esp32s3-5-epaper/platformio.ini
+++ b/variants/esp32s3/crowpanel-esp32s3-5-epaper/platformio.ini
@@ -16,7 +16,6 @@ build_flags =
   -I variants/esp32s3/crowpanel-esp32s3-5-epaper
   -D PRIVATE_HW
   -DBOARD_HAS_PSRAM
-  -DGPS_POWER_TOGGLE
   -DEINK_DISPLAY_MODEL=GxEPD2_579_GDEY0579T93 ;https://www.good-display.com/product/439.html
   -DEINK_WIDTH=792
   -DEINK_HEIGHT=272
@@ -46,7 +45,6 @@ build_flags =
   -I variants/esp32s3/crowpanel-esp32s3-5-epaper
   -D PRIVATE_HW
   -DBOARD_HAS_PSRAM
-  -DGPS_POWER_TOGGLE
   -DEINK_DISPLAY_MODEL=GxEPD2_420_GYE042A87   ; similar Panel: GDEY042T81 : https://www.good-display.com/product/386.html
   -DEINK_WIDTH=400
   -DEINK_HEIGHT=300
@@ -76,7 +74,6 @@ build_flags =
   -I variants/esp32s3/crowpanel-esp32s3-5-epaper
   -D PRIVATE_HW
   -DBOARD_HAS_PSRAM
-  -DGPS_POWER_TOGGLE
   -DEINK_DISPLAY_MODEL=GxEPD2_290_GDEY029T94 ;https://www.good-display.com/product/389.html
   -DEINK_WIDTH=296
   -DEINK_HEIGHT=128
diff --git a/variants/esp32s3/heltec_capsule_sensor_v3/platformio.ini b/variants/esp32s3/heltec_capsule_sensor_v3/platformio.ini
index d43ffd0df..0bb21581a 100644
--- a/variants/esp32s3/heltec_capsule_sensor_v3/platformio.ini
+++ b/variants/esp32s3/heltec_capsule_sensor_v3/platformio.ini
@@ -6,5 +6,4 @@ board_build.partitions = default_8MB.csv
 build_flags = 
   ${esp32s3_base.build_flags} -I variants/esp32s3/heltec_capsule_sensor_v3
   -D HELTEC_CAPSULE_SENSOR_V3
-  -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   ;-D DEBUG_DISABLED ; uncomment this line to disable DEBUG output
diff --git a/variants/esp32s3/heltec_v3/platformio.ini b/variants/esp32s3/heltec_v3/platformio.ini
index b521e11ca..af0854e49 100644
--- a/variants/esp32s3/heltec_v3/platformio.ini
+++ b/variants/esp32s3/heltec_v3/platformio.ini
@@ -8,4 +8,3 @@ build_flags =
   ${esp32s3_base.build_flags}
   -D HELTEC_V3
   -I variants/esp32s3/heltec_v3
-  -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
diff --git a/variants/esp32s3/heltec_v4/platformio.ini b/variants/esp32s3/heltec_v4/platformio.ini
index d0a250ad3..7057f9646 100644
--- a/variants/esp32s3/heltec_v4/platformio.ini
+++ b/variants/esp32s3/heltec_v4/platformio.ini
@@ -7,4 +7,3 @@ build_flags =
   ${esp32s3_base.build_flags}
   -D HELTEC_V4
   -I variants/esp32s3/heltec_v4
-  -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
diff --git a/variants/esp32s3/heltec_wireless_tracker/platformio.ini b/variants/esp32s3/heltec_wireless_tracker/platformio.ini
index 2faba45a8..3a373bf4f 100644
--- a/variants/esp32s3/heltec_wireless_tracker/platformio.ini
+++ b/variants/esp32s3/heltec_wireless_tracker/platformio.ini
@@ -8,7 +8,6 @@ build_flags =
   ${esp32s3_base.build_flags}
   -I variants/esp32s3/heltec_wireless_tracker
   -D HELTEC_TRACKER_V1_1
-  -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   ;-D DEBUG_DISABLED ; uncomment this line to disable DEBUG output
 
 lib_deps =
diff --git a/variants/esp32s3/heltec_wireless_tracker_V1_0/platformio.ini b/variants/esp32s3/heltec_wireless_tracker_V1_0/platformio.ini
index 89fe4b385..cd961533d 100644
--- a/variants/esp32s3/heltec_wireless_tracker_V1_0/platformio.ini
+++ b/variants/esp32s3/heltec_wireless_tracker_V1_0/platformio.ini
@@ -8,7 +8,6 @@ build_flags =
   ${esp32s3_base.build_flags}
   -I variants/esp32s3/heltec_wireless_tracker_V1_0
   -D HELTEC_TRACKER_V1_0
-  -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   ;-D DEBUG_DISABLED ; uncomment this line to disable DEBUG output
 lib_deps =
   ${esp32s3_base.lib_deps}
diff --git a/variants/esp32s3/heltec_wireless_tracker_v2/platformio.ini b/variants/esp32s3/heltec_wireless_tracker_v2/platformio.ini
index 4872561db..0f9265f91 100644
--- a/variants/esp32s3/heltec_wireless_tracker_v2/platformio.ini
+++ b/variants/esp32s3/heltec_wireless_tracker_v2/platformio.ini
@@ -8,7 +8,6 @@ build_flags =
   ${esp32s3_base.build_flags}
   -I variants/esp32s3/heltec_wireless_tracker_v2
   -D HELTEC_WIRELESS_TRACKER_V2
-  -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
 lib_deps =
   ${esp32s3_base.lib_deps}
   lovyan03/LovyanGFX@^1.2.0
diff --git a/variants/esp32s3/heltec_wsl_v3/platformio.ini b/variants/esp32s3/heltec_wsl_v3/platformio.ini
index 06cde2304..c038a463e 100644
--- a/variants/esp32s3/heltec_wsl_v3/platformio.ini
+++ b/variants/esp32s3/heltec_wsl_v3/platformio.ini
@@ -7,4 +7,3 @@ build_flags =
   ${esp32s3_base.build_flags}
   -D HELTEC_WSL_V3
   -I variants/esp32s3/heltec_wsl_v3
-  -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
diff --git a/variants/esp32s3/link32_s3_v1/platformio.ini b/variants/esp32s3/link32_s3_v1/platformio.ini
index c1b71b3b5..8d88075c4 100644
--- a/variants/esp32s3/link32_s3_v1/platformio.ini
+++ b/variants/esp32s3/link32_s3_v1/platformio.ini
@@ -5,7 +5,6 @@ build_flags =
   ${esp32_base.build_flags}
   -D LINK_32
   -I variants/esp32s3/link32_s3_v1
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   -DARDUINO_USB_CDC_ON_BOOT
   -DARDUINO_USB_MODE=1
   -DRADIOLIB_EXCLUDE_SX128X=1
diff --git a/variants/esp32s3/t-deck-pro/platformio.ini b/variants/esp32s3/t-deck-pro/platformio.ini
index 45c3ae4ea..0b3c7843a 100644
--- a/variants/esp32s3/t-deck-pro/platformio.ini
+++ b/variants/esp32s3/t-deck-pro/platformio.ini
@@ -7,7 +7,6 @@ upload_protocol = esptool
 build_flags = 
   ${esp32_base.build_flags} -I variants/esp32s3/t-deck-pro
   -D T_DECK_PRO
-  -D GPS_POWER_TOGGLE
   -D USE_EINK
   -D EINK_DISPLAY_MODEL=GxEPD2_310_GDEQ031T10
   -D EINK_WIDTH=240
diff --git a/variants/esp32s3/t-deck/platformio.ini b/variants/esp32s3/t-deck/platformio.ini
index 7c8070c3e..9ab0756d1 100644
--- a/variants/esp32s3/t-deck/platformio.ini
+++ b/variants/esp32s3/t-deck/platformio.ini
@@ -9,7 +9,6 @@ upload_protocol = esptool
 build_flags = ${esp32s3_base.build_flags} 
   -D T_DECK 
   -D BOARD_HAS_PSRAM
-  -D GPS_POWER_TOGGLE
   -I variants/esp32s3/t-deck
 
 lib_deps = ${esp32s3_base.lib_deps}
diff --git a/variants/esp32s3/t-eth-elite/platformio.ini b/variants/esp32s3/t-eth-elite/platformio.ini
index 6107185ce..1a5823bc3 100644
--- a/variants/esp32s3/t-eth-elite/platformio.ini
+++ b/variants/esp32s3/t-eth-elite/platformio.ini
@@ -9,7 +9,6 @@ build_flags =
   -D T_ETH_ELITE
   -D HAS_UDP_MULTICAST=1
   -I variants/esp32s3/t-eth-elite
-  -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
 
 lib_ignore = 
     Ethernet
diff --git a/variants/esp32s3/tlora-pager/platformio.ini b/variants/esp32s3/tlora-pager/platformio.ini
index 9800161bb..d63537904 100644
--- a/variants/esp32s3/tlora-pager/platformio.ini
+++ b/variants/esp32s3/tlora-pager/platformio.ini
@@ -10,7 +10,6 @@ build_flags = ${esp32s3_base.build_flags}
   -I variants/esp32s3/tlora-pager
   -D T_LORA_PAGER 
   -D BOARD_HAS_PSRAM
-  -D GPS_POWER_TOGGLE
   -D HAS_SDCARD
   -D SDCARD_USE_SPI1
   -D ENABLE_ROTARY_PULLUP
diff --git a/variants/esp32s3/tlora_t3s3_epaper/platformio.ini b/variants/esp32s3/tlora_t3s3_epaper/platformio.ini
index 71644ee77..eca052f57 100644
--- a/variants/esp32s3/tlora_t3s3_epaper/platformio.ini
+++ b/variants/esp32s3/tlora_t3s3_epaper/platformio.ini
@@ -8,7 +8,6 @@ build_flags =
   ${esp32_base.build_flags}
   -D TLORA_T3S3_EPAPER
   -I variants/esp32s3/tlora_t3s3_epaper
-  -DGPS_POWER_TOGGLE
   -DUSE_EINK
   -DEINK_DISPLAY_MODEL=GxEPD2_213_BN
   -DEINK_WIDTH=250
diff --git a/variants/esp32s3/tlora_t3s3_v1/platformio.ini b/variants/esp32s3/tlora_t3s3_v1/platformio.ini
index d9624f043..56ece0d62 100644
--- a/variants/esp32s3/tlora_t3s3_v1/platformio.ini
+++ b/variants/esp32s3/tlora_t3s3_v1/platformio.ini
@@ -6,4 +6,3 @@ upload_protocol = esptool
 
 build_flags = 
   ${esp32_base.build_flags} -D TLORA_T3S3_V1 -I variants/esp32s3/tlora_t3s3_v1
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
diff --git a/variants/esp32s3/tracksenger/platformio.ini b/variants/esp32s3/tracksenger/platformio.ini
index 0e9f08541..213a917b1 100644
--- a/variants/esp32s3/tracksenger/platformio.ini
+++ b/variants/esp32s3/tracksenger/platformio.ini
@@ -8,7 +8,6 @@ build_flags =
   ${esp32s3_base.build_flags}
   -I variants/esp32s3/tracksenger/internal
   -D HELTEC_TRACKER_V1_1
-  -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   ;-D DEBUG_DISABLED ; uncomment this line to disable DEBUG output
 
 lib_deps =
@@ -25,7 +24,6 @@ build_flags =
   ${esp32s3_base.build_flags}
   -I variants/esp32s3/tracksenger/lcd
   -D HELTEC_TRACKER_V1_1
-  -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   ;-D DEBUG_DISABLED ; uncomment this line to disable DEBUG output
 
 lib_deps =
@@ -42,5 +40,4 @@ build_flags =
   ${esp32s3_base.build_flags}
   -I variants/esp32s3/tracksenger/oled
   -D HELTEC_TRACKER_V1_1
-  -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   ;-D DEBUG_DISABLED ; uncomment this line to disable DEBUG output
diff --git a/variants/nrf52840/ELECROW-ThinkNode-M1/platformio.ini b/variants/nrf52840/ELECROW-ThinkNode-M1/platformio.ini
index 0578bcfe8..f89b05d1f 100644
--- a/variants/nrf52840/ELECROW-ThinkNode-M1/platformio.ini
+++ b/variants/nrf52840/ELECROW-ThinkNode-M1/platformio.ini
@@ -9,7 +9,6 @@ debug_tool = jlink
 build_flags = ${nrf52840_base.build_flags}
   -Ivariants/nrf52840/ELECROW-ThinkNode-M1
   -DELECROW_ThinkNode_M1
-  -DGPS_POWER_TOGGLE
   -DUSE_EINK
   -DEINK_DISPLAY_MODEL=GxEPD2_154_D67
   -DEINK_WIDTH=200
diff --git a/variants/nrf52840/ME25LS01-4Y10TD/platformio.ini b/variants/nrf52840/ME25LS01-4Y10TD/platformio.ini
index 89a45694c..1279f12c6 100644
--- a/variants/nrf52840/ME25LS01-4Y10TD/platformio.ini
+++ b/variants/nrf52840/ME25LS01-4Y10TD/platformio.ini
@@ -8,7 +8,6 @@ build_flags = ${nrf52840_base.build_flags}
   -Isrc/platform/nrf52/softdevice
   -Isrc/platform/nrf52/softdevice/nrf52
   -DME25LS01_4Y10TD
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
 board_build.ldscript = src/platform/nrf52/nrf52840_s140_v7.ld
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/ME25LS01-4Y10TD>
 lib_deps = 
diff --git a/variants/nrf52840/ME25LS01-4Y10TD_e-ink/platformio.ini b/variants/nrf52840/ME25LS01-4Y10TD_e-ink/platformio.ini
index ad5867bd5..f8d6da008 100644
--- a/variants/nrf52840/ME25LS01-4Y10TD_e-ink/platformio.ini
+++ b/variants/nrf52840/ME25LS01-4Y10TD_e-ink/platformio.ini
@@ -8,7 +8,6 @@ build_flags = ${nrf52840_base.build_flags}
   -Isrc/platform/nrf52/softdevice
   -Isrc/platform/nrf52/softdevice/nrf52
   -DME25LS01_4Y10TD
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   -DEINK_DISPLAY_MODEL=GxEPD2_420_GDEY042T81
   -DEINK_WIDTH=400
   -DEINK_HEIGHT=300
diff --git a/variants/nrf52840/MS24SF1/platformio.ini b/variants/nrf52840/MS24SF1/platformio.ini
index f162cbd60..df15b5605 100644
--- a/variants/nrf52840/MS24SF1/platformio.ini
+++ b/variants/nrf52840/MS24SF1/platformio.ini
@@ -7,7 +7,6 @@ build_flags = ${nrf52840_base.build_flags}
   -Ivariants/nrf52840/MS24SF1
   -Isrc/platform/nrf52/softdevice
   -Isrc/platform/nrf52/softdevice/nrf52
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
 board_build.ldscript = src/platform/nrf52/nrf52840_s140_v7.ld
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/MS24SF1>
 lib_deps =
diff --git a/variants/nrf52840/diy/nrf52_promicro_diy_tcxo/variant.h b/variants/nrf52840/diy/nrf52_promicro_diy_tcxo/variant.h
index e93442c7e..87342a02f 100644
--- a/variants/nrf52840/diy/nrf52_promicro_diy_tcxo/variant.h
+++ b/variants/nrf52840/diy/nrf52_promicro_diy_tcxo/variant.h
@@ -94,7 +94,6 @@ NRF52 PRO MICRO PIN ASSIGNMENT
 #define PIN_GPS_RX (0 + 20) // P0.20
 
 #define PIN_GPS_EN (0 + 24) // P0.24
-#define GPS_POWER_TOGGLE
 #define GPS_UBLOX
 // define GPS_DEBUG
 
diff --git a/variants/nrf52840/diy/nrf52_promicro_diy_xtal/variant.h b/variants/nrf52840/diy/nrf52_promicro_diy_xtal/variant.h
index 7aafab7da..6e208e79f 100644
--- a/variants/nrf52840/diy/nrf52_promicro_diy_xtal/variant.h
+++ b/variants/nrf52840/diy/nrf52_promicro_diy_xtal/variant.h
@@ -93,7 +93,6 @@ NRF52 PRO MICRO PIN ASSIGNMENT
 #define PIN_GPS_RX (0 + 20) // P0.20
 
 #define PIN_GPS_EN (0 + 24) // P0.24
-#define GPS_POWER_TOGGLE
 #define GPS_UBLOX
 // define GPS_DEBUG
 
diff --git a/variants/nrf52840/gat562_mesh_trial_tracker/platformio.ini b/variants/nrf52840/gat562_mesh_trial_tracker/platformio.ini
index c6a5a7399..c6cd23314 100644
--- a/variants/nrf52840/gat562_mesh_trial_tracker/platformio.ini
+++ b/variants/nrf52840/gat562_mesh_trial_tracker/platformio.ini
@@ -8,7 +8,6 @@ build_flags = ${nrf52840_base.build_flags}
   -I variants/nrf52840/gat562_mesh_trial_tracker
   ;-D GAT562_MESH_TRIAL_TRACKER
   -D PRIVATE_HW
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   -DRADIOLIB_EXCLUDE_SX128X=1
   -DRADIOLIB_EXCLUDE_SX127X=1
   -DRADIOLIB_EXCLUDE_LR11X0=1
diff --git a/variants/nrf52840/heltec_mesh_node_t114/platformio.ini b/variants/nrf52840/heltec_mesh_node_t114/platformio.ini
index c7b30b339..c49dadd56 100644
--- a/variants/nrf52840/heltec_mesh_node_t114/platformio.ini
+++ b/variants/nrf52840/heltec_mesh_node_t114/platformio.ini
@@ -8,7 +8,6 @@ debug_tool = jlink
 # add -DCFG_SYSVIEW if you want to use the Segger systemview tool for OS profiling.
 build_flags = ${nrf52840_base.build_flags}
   -Ivariants/nrf52840/heltec_mesh_node_t114
-  -DGPS_POWER_TOGGLE
   -DHELTEC_T114
 
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/heltec_mesh_node_t114>
diff --git a/variants/nrf52840/heltec_mesh_solar/platformio.ini b/variants/nrf52840/heltec_mesh_solar/platformio.ini
index 625dd1d43..36a7904d6 100644
--- a/variants/nrf52840/heltec_mesh_solar/platformio.ini
+++ b/variants/nrf52840/heltec_mesh_solar/platformio.ini
@@ -8,7 +8,6 @@ debug_tool = jlink
 # add -DCFG_SYSVIEW if you want to use the Segger systemview tool for OS profiling.
 build_flags = ${nrf52840_base.build_flags}
   -Ivariants/nrf52840/heltec_mesh_solar
-  -DGPS_POWER_TOGGLE
   -DHELTEC_MESH_SOLAR
 
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/heltec_mesh_solar>
diff --git a/variants/nrf52840/meshlink/platformio.ini b/variants/nrf52840/meshlink/platformio.ini
index 466362242..2a4e27fe8 100644
--- a/variants/nrf52840/meshlink/platformio.ini
+++ b/variants/nrf52840/meshlink/platformio.ini
@@ -9,7 +9,6 @@ board_level = extra
 build_flags = ${nrf52840_base.build_flags}
   -I variants/nrf52840/meshlink
   -D MESHLINK
-  -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   -D EINK_DISPLAY_MODEL=GxEPD2_213_B74
   -D EINK_WIDTH=250
   -D EINK_HEIGHT=122
diff --git a/variants/nrf52840/meshlink_eink/platformio.ini b/variants/nrf52840/meshlink_eink/platformio.ini
index af5a0040e..c0c0cb1dd 100644
--- a/variants/nrf52840/meshlink_eink/platformio.ini
+++ b/variants/nrf52840/meshlink_eink/platformio.ini
@@ -9,7 +9,6 @@ board_level = extra
 build_flags = ${nrf52840_base.build_flags}
   -I variants/nrf52840/meshlink_eink
   -D MESHLINK
-  -D GPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   -D EINK_DISPLAY_MODEL=GxEPD2_213_B74
   -D EINK_WIDTH=250
   -D EINK_HEIGHT=122
diff --git a/variants/nrf52840/r1-neo/platformio.ini b/variants/nrf52840/r1-neo/platformio.ini
index 6feb55dc9..60f1f6ae1 100644
--- a/variants/nrf52840/r1-neo/platformio.ini
+++ b/variants/nrf52840/r1-neo/platformio.ini
@@ -6,7 +6,6 @@ board_check = true
 build_flags = ${nrf52840_base.build_flags}
   -Ivariants/nrf52840/r1-neo
   -D R1_NEO
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   -DRADIOLIB_EXCLUDE_SX128X=1
   -DRADIOLIB_EXCLUDE_SX127X=1
   -DRADIOLIB_EXCLUDE_LR11X0=1
diff --git a/variants/nrf52840/rak2560/platformio.ini b/variants/nrf52840/rak2560/platformio.ini
index edc648b9b..021e6d03b 100644
--- a/variants/nrf52840/rak2560/platformio.ini
+++ b/variants/nrf52840/rak2560/platformio.ini
@@ -6,7 +6,6 @@ board_check = true
 build_flags = ${nrf52840_base.build_flags}
   -I variants/nrf52840/rak2560
   -D RAK_4631
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   -DRADIOLIB_EXCLUDE_SX128X=1
   -DRADIOLIB_EXCLUDE_SX127X=1
   -DRADIOLIB_EXCLUDE_LR11X0=1
diff --git a/variants/nrf52840/rak4631/platformio.ini b/variants/nrf52840/rak4631/platformio.ini
index 6bf5f44cb..205966529 100644
--- a/variants/nrf52840/rak4631/platformio.ini
+++ b/variants/nrf52840/rak4631/platformio.ini
@@ -7,7 +7,6 @@ board_check = true
 build_flags = ${nrf52840_base.build_flags}
   -I variants/nrf52840/rak4631
   -D RAK_4631
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   -DEINK_DISPLAY_MODEL=GxEPD2_213_BN
   -DEINK_WIDTH=250
   -DEINK_HEIGHT=122
diff --git a/variants/nrf52840/rak4631_eth_gw/platformio.ini b/variants/nrf52840/rak4631_eth_gw/platformio.ini
index 4be8843a2..3c61e3498 100644
--- a/variants/nrf52840/rak4631_eth_gw/platformio.ini
+++ b/variants/nrf52840/rak4631_eth_gw/platformio.ini
@@ -6,7 +6,6 @@ board_check = true
 build_flags = ${nrf52840_base.build_flags}
   -I variants/nrf52840/rak4631_eth_gw
   -D RAK_4631
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   -DHAS_UDP_MULTICAST=1
   -DEINK_DISPLAY_MODEL=GxEPD2_213_BN
   -DEINK_WIDTH=250
diff --git a/variants/nrf52840/rak4631_nomadstar_meteor_pro/platformio.ini b/variants/nrf52840/rak4631_nomadstar_meteor_pro/platformio.ini
index e94eef1ee..d7dab2678 100644
--- a/variants/nrf52840/rak4631_nomadstar_meteor_pro/platformio.ini
+++ b/variants/nrf52840/rak4631_nomadstar_meteor_pro/platformio.ini
@@ -6,7 +6,6 @@ board_check = true
 build_flags = ${nrf52840_base.build_flags}
   -I variants/nrf52840/rak4631_nomadstar_meteor_pro
   -D NOMADSTAR_METEOR_PRO
-  ;-DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   -DEINK_DISPLAY_MODEL=GxEPD2_213_BN
   -DEINK_WIDTH=250
   -DEINK_HEIGHT=122
diff --git a/variants/nrf52840/rak_wismeshtag/platformio.ini b/variants/nrf52840/rak_wismeshtag/platformio.ini
index 08e723302..f04d1f186 100644
--- a/variants/nrf52840/rak_wismeshtag/platformio.ini
+++ b/variants/nrf52840/rak_wismeshtag/platformio.ini
@@ -7,7 +7,6 @@ build_flags = ${nrf52840_base.build_flags}
   -I variants/nrf52840/rak_wismeshtag
   -D WISMESH_TAG
   -D RAK_4631
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   -DRADIOLIB_EXCLUDE_SX128X=1
   -DRADIOLIB_EXCLUDE_SX127X=1
   -DRADIOLIB_EXCLUDE_LR11X0=1
diff --git a/variants/nrf52840/rak_wismeshtap/platformio.ini b/variants/nrf52840/rak_wismeshtap/platformio.ini
index adf301537..3369f9c77 100644
--- a/variants/nrf52840/rak_wismeshtap/platformio.ini
+++ b/variants/nrf52840/rak_wismeshtap/platformio.ini
@@ -6,7 +6,6 @@ build_flags = ${nrf52840_base.build_flags}
   -Ivariants/nrf52840/rak_wismeshtap
   -DWISMESH_TAP
   -DRAK_4631
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   -DEINK_DISPLAY_MODEL=GxEPD2_213_BN
   -DEINK_WIDTH=250
   -DEINK_HEIGHT=122
diff --git a/variants/nrf52840/t-echo-lite/platformio.ini b/variants/nrf52840/t-echo-lite/platformio.ini
index 68ae59dcb..90e6487a7 100644
--- a/variants/nrf52840/t-echo-lite/platformio.ini
+++ b/variants/nrf52840/t-echo-lite/platformio.ini
@@ -9,7 +9,6 @@ debug_tool = jlink
 build_flags = ${nrf52840_base.build_flags}
   -Ivariants/nrf52840/t-echo-lite
   -D T_ECHO_LITE
-  -D GPS_POWER_TOGGLE
   -D EINK_DISPLAY_MODEL=GxEPD2_122_T61
   -D EINK_WIDTH=192
   -D EINK_HEIGHT=176
diff --git a/variants/nrf52840/t-echo/platformio.ini b/variants/nrf52840/t-echo/platformio.ini
index 6541c9796..051fb3099 100644
--- a/variants/nrf52840/t-echo/platformio.ini
+++ b/variants/nrf52840/t-echo/platformio.ini
@@ -9,7 +9,6 @@ debug_tool = jlink
 # add -DCFG_SYSVIEW if you want to use the Segger systemview tool for OS profiling.
 build_flags = ${nrf52840_base.build_flags}
   -Ivariants/nrf52840/t-echo
-  -DGPS_POWER_TOGGLE
   -DEINK_DISPLAY_MODEL=GxEPD2_154_D67
   -DEINK_WIDTH=200
   -DEINK_HEIGHT=200
diff --git a/variants/nrf52840/tracker-t1000-e/platformio.ini b/variants/nrf52840/tracker-t1000-e/platformio.ini
index c6c3f269c..905d751fd 100644
--- a/variants/nrf52840/tracker-t1000-e/platformio.ini
+++ b/variants/nrf52840/tracker-t1000-e/platformio.ini
@@ -7,7 +7,6 @@ build_flags = ${nrf52840_base.build_flags}
   -Isrc/platform/nrf52/softdevice
   -Isrc/platform/nrf52/softdevice/nrf52
   -DTRACKER_T1000_E
-  -DGPS_POWER_TOGGLE
   -DMESHTASTIC_EXCLUDE_ENVIRONMENTAL_SENSOR_EXTERNAL=1
   -DMESHTASTIC_EXCLUDE_CANNEDMESSAGES=1
   -DMESHTASTIC_EXCLUDE_SCREEN=1
diff --git a/variants/nrf52840/wio-sdk-wm1110/platformio.ini b/variants/nrf52840/wio-sdk-wm1110/platformio.ini
index 2c65246b8..028129783 100644
--- a/variants/nrf52840/wio-sdk-wm1110/platformio.ini
+++ b/variants/nrf52840/wio-sdk-wm1110/platformio.ini
@@ -14,7 +14,6 @@ build_flags = ${nrf52840_base.build_flags}
   -Isrc/platform/nrf52/softdevice
   -Isrc/platform/nrf52/softdevice/nrf52
   -DWIO_WM1110
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
   -DCFG_TUD_CDC=0
 board_build.ldscript = src/platform/nrf52/nrf52840_s140_v7.ld
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/wio-sdk-wm1110>
diff --git a/variants/nrf52840/wio-t1000-s/platformio.ini b/variants/nrf52840/wio-t1000-s/platformio.ini
index 3594bcf07..c6b61fc8a 100644
--- a/variants/nrf52840/wio-t1000-s/platformio.ini
+++ b/variants/nrf52840/wio-t1000-s/platformio.ini
@@ -8,7 +8,6 @@ build_flags = ${nrf52840_base.build_flags}
   -Isrc/platform/nrf52/softdevice
   -Isrc/platform/nrf52/softdevice/nrf52
   -DWIO_WM1110
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
 board_build.ldscript = src/platform/nrf52/nrf52840_s140_v7.ld
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/wio-t1000-s>
 lib_deps = 
diff --git a/variants/nrf52840/wio-tracker-wm1110/platformio.ini b/variants/nrf52840/wio-tracker-wm1110/platformio.ini
index b383043bb..73b7dedd4 100644
--- a/variants/nrf52840/wio-tracker-wm1110/platformio.ini
+++ b/variants/nrf52840/wio-tracker-wm1110/platformio.ini
@@ -7,7 +7,6 @@ build_flags = ${nrf52840_base.build_flags}
   -Isrc/platform/nrf52/softdevice
   -Isrc/platform/nrf52/softdevice/nrf52
   -DWIO_WM1110
-  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
 board_build.ldscript = src/platform/nrf52/nrf52840_s140_v7.ld
 build_src_filter = ${nrf52_base.build_src_filter} +<../variants/nrf52840/wio-tracker-wm1110>
 lib_deps =