mirror of
https://github.com/meshtastic/firmware.git
synced 2025-02-01 02:09:57 +00:00
Separate RAK4631 and RAK2560 variants
This commit is contained in:
beegee-tokyo
parent
85d621d9c6
commit
f50073ed9f
@ -2,7 +2,7 @@
|
||||
; https://docs.platformio.org/page/projectconf.html
|
||||
|
||||
[platformio]
|
||||
;default_envs = tbeam
|
||||
default_envs = tbeam
|
||||
;default_envs = pico
|
||||
;default_envs = tbeam-s3-core
|
||||
;default_envs = tbeam0.7
|
||||
@ -29,7 +29,7 @@
|
||||
;default_envs = meshtastic-dr-dev
|
||||
;default_envs = m5stack-coreink
|
||||
;default_envs = rak4631
|
||||
default_envs = rak2560
|
||||
;default_envs = rak2560
|
||||
;default_envs = rak10701
|
||||
;default_envs = wio-e5
|
||||
;default_envs = radiomaster_900_bandit_nano
|
||||
|
||||
@ -3,14 +3,11 @@
|
||||
extends = nrf52840_base
|
||||
board = wiscore_rak4631
|
||||
board_check = true
|
||||
build_flags = ${nrf52840_base.build_flags} -Ivariants/rak4631 -D RAK_4631
|
||||
build_flags = ${nrf52840_base.build_flags} -Ivariants/rak2560 -D RAK_4631
|
||||
-L "${platformio.libdeps_dir}/${this.__env__}/bsec2/src/cortex-m4/fpv4-sp-d16-hard"
|
||||
-DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
|
||||
-DEINK_DISPLAY_MODEL=GxEPD2_213_BN
|
||||
-DEINK_WIDTH=250
|
||||
-DEINK_HEIGHT=122
|
||||
-DHAS_RAKPROT=1 ; Define if RAk OneWireSerial is used (disables GPS)
|
||||
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/rak4631> +<../variants/rak2560> +<mesh/eth/> +<mesh/api/> +<mqtt/>
|
||||
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/rak2560> +<mesh/eth/> +<mesh/api/> +<mqtt/>
|
||||
lib_deps =
|
||||
${nrf52840_base.lib_deps}
|
||||
${networking_base.lib_deps}
|
||||
|
||||
45
variants/rak2560/variant.cpp
Normal file
45
variants/rak2560/variant.cpp
Normal file
@ -0,0 +1,45 @@
|
||||
/*
|
||||
Copyright (c) 2014-2015 Arduino LLC. All right reserved.
|
||||
Copyright (c) 2016 Sandeep Mistry All right reserved.
|
||||
Copyright (c) 2018, Adafruit Industries (adafruit.com)
|
||||
|
||||
This library is free software; you can redistribute it and/or
|
||||
modify it under the terms of the GNU Lesser General Public
|
||||
License as published by the Free Software Foundation; either
|
||||
version 2.1 of the License, or (at your option) any later version.
|
||||
|
||||
This library is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
||||
See the GNU Lesser General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU Lesser General Public
|
||||
License along with this library; if not, write to the Free Software
|
||||
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
|
||||
*/
|
||||
|
||||
#include "variant.h"
|
||||
#include "nrf.h"
|
||||
#include "wiring_constants.h"
|
||||
#include "wiring_digital.h"
|
||||
|
||||
const uint32_t g_ADigitalPinMap[] = {
|
||||
// P0
|
||||
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31,
|
||||
|
||||
// P1
|
||||
32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47};
|
||||
|
||||
void initVariant()
|
||||
{
|
||||
// LED1 & LED2
|
||||
pinMode(PIN_LED1, OUTPUT);
|
||||
ledOff(PIN_LED1);
|
||||
|
||||
pinMode(PIN_LED2, OUTPUT);
|
||||
ledOff(PIN_LED2);
|
||||
|
||||
// 3V3 Power Rail
|
||||
pinMode(PIN_3V3_EN, OUTPUT);
|
||||
digitalWrite(PIN_3V3_EN, HIGH);
|
||||
}
|
||||
280
variants/rak2560/variant.h
Normal file
280
variants/rak2560/variant.h
Normal file
@ -0,0 +1,280 @@
|
||||
/*
|
||||
Copyright (c) 2014-2015 Arduino LLC. All right reserved.
|
||||
Copyright (c) 2016 Sandeep Mistry All right reserved.
|
||||
Copyright (c) 2018, Adafruit Industries (adafruit.com)
|
||||
|
||||
This library is free software; you can redistribute it and/or
|
||||
modify it under the terms of the GNU Lesser General Public
|
||||
License as published by the Free Software Foundation; either
|
||||
version 2.1 of the License, or (at your option) any later version.
|
||||
This library is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
||||
See the GNU Lesser General Public License for more details.
|
||||
You should have received a copy of the GNU Lesser General Public
|
||||
License along with this library; if not, write to the Free Software
|
||||
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
|
||||
*/
|
||||
|
||||
#ifndef _VARIANT_RAK4630_
|
||||
#define _VARIANT_RAK4630_
|
||||
|
||||
#define RAK4630
|
||||
|
||||
/** Master clock frequency */
|
||||
#define VARIANT_MCK (64000000ul)
|
||||
|
||||
#define USE_LFXO // Board uses 32khz crystal for LF
|
||||
// define USE_LFRC // Board uses RC for LF
|
||||
|
||||
/*----------------------------------------------------------------------------
|
||||
* Headers
|
||||
*----------------------------------------------------------------------------*/
|
||||
|
||||
#include "WVariant.h"
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif // __cplusplus
|
||||
|
||||
// Number of pins defined in PinDescription array
|
||||
#define PINS_COUNT (48)
|
||||
#define NUM_DIGITAL_PINS (48)
|
||||
#define NUM_ANALOG_INPUTS (6)
|
||||
#define NUM_ANALOG_OUTPUTS (0)
|
||||
|
||||
// LEDs
|
||||
#define PIN_LED1 (35)
|
||||
#define PIN_LED2 (36)
|
||||
|
||||
#define LED_BUILTIN PIN_LED1
|
||||
#define LED_CONN PIN_LED2
|
||||
|
||||
#define LED_GREEN PIN_LED1
|
||||
#define LED_BLUE PIN_LED2
|
||||
|
||||
#define LED_STATE_ON 1 // State when LED is litted
|
||||
|
||||
/*
|
||||
* Buttons
|
||||
*/
|
||||
|
||||
#define PIN_BUTTON1 9 // Pin for button on E-ink button module or IO expansion
|
||||
#define BUTTON_NEED_PULLUP
|
||||
#define PIN_BUTTON2 12
|
||||
#define PIN_BUTTON3 24
|
||||
#define PIN_BUTTON4 25
|
||||
|
||||
/*
|
||||
* Analog pins
|
||||
*/
|
||||
#define PIN_A0 (5)
|
||||
#define PIN_A1 (31)
|
||||
#define PIN_A2 (28)
|
||||
#define PIN_A3 (29)
|
||||
#define PIN_A4 (30)
|
||||
#define PIN_A5 (31)
|
||||
#define PIN_A6 (0xff)
|
||||
#define PIN_A7 (0xff)
|
||||
|
||||
static const uint8_t A0 = PIN_A0;
|
||||
static const uint8_t A1 = PIN_A1;
|
||||
static const uint8_t A2 = PIN_A2;
|
||||
static const uint8_t A3 = PIN_A3;
|
||||
static const uint8_t A4 = PIN_A4;
|
||||
static const uint8_t A5 = PIN_A5;
|
||||
static const uint8_t A6 = PIN_A6;
|
||||
static const uint8_t A7 = PIN_A7;
|
||||
#define ADC_RESOLUTION 14
|
||||
|
||||
// Other pins
|
||||
#define PIN_AREF (2)
|
||||
#define PIN_NFC1 (9)
|
||||
#define PIN_NFC2 (10)
|
||||
|
||||
static const uint8_t AREF = PIN_AREF;
|
||||
|
||||
/*
|
||||
* Serial interfaces
|
||||
*/
|
||||
#define PIN_SERIAL1_RX (15)
|
||||
#define PIN_SERIAL1_TX (16)
|
||||
|
||||
// Connected to Serial 2
|
||||
#define PIN_SERIAL2_RX (19)
|
||||
#define PIN_SERIAL2_TX (20)
|
||||
|
||||
/*
|
||||
* SPI Interfaces
|
||||
*/
|
||||
#define SPI_INTERFACES_COUNT 2
|
||||
|
||||
#define PIN_SPI_MISO (45)
|
||||
#define PIN_SPI_MOSI (44)
|
||||
#define PIN_SPI_SCK (43)
|
||||
|
||||
#define PIN_SPI1_MISO (29) // (0 + 29)
|
||||
#define PIN_SPI1_MOSI (30) // (0 + 30)
|
||||
#define PIN_SPI1_SCK (3) // (0 + 3)
|
||||
|
||||
static const uint8_t SS = 42;
|
||||
static const uint8_t MOSI = PIN_SPI_MOSI;
|
||||
static const uint8_t MISO = PIN_SPI_MISO;
|
||||
static const uint8_t SCK = PIN_SPI_SCK;
|
||||
|
||||
/*
|
||||
* eink display pins
|
||||
*/
|
||||
|
||||
#define PIN_EINK_CS (0 + 26)
|
||||
#define PIN_EINK_BUSY (0 + 4)
|
||||
#define PIN_EINK_DC (0 + 17)
|
||||
#define PIN_EINK_RES (-1)
|
||||
#define PIN_EINK_SCLK (0 + 3)
|
||||
#define PIN_EINK_MOSI (0 + 30) // also called SDI
|
||||
|
||||
// #define USE_EINK
|
||||
|
||||
/*
|
||||
* Wire Interfaces
|
||||
*/
|
||||
#define WIRE_INTERFACES_COUNT 1
|
||||
|
||||
#define PIN_WIRE_SDA (13)
|
||||
#define PIN_WIRE_SCL (14)
|
||||
|
||||
// QSPI Pins
|
||||
#define PIN_QSPI_SCK 3
|
||||
#define PIN_QSPI_CS 26
|
||||
#define PIN_QSPI_IO0 30
|
||||
#define PIN_QSPI_IO1 29
|
||||
#define PIN_QSPI_IO2 28
|
||||
#define PIN_QSPI_IO3 2
|
||||
|
||||
/* @note RAK5005-O GPIO mapping to RAK4631 GPIO ports
|
||||
RAK5005-O <-> nRF52840
|
||||
IO1 <-> P0.17 (Arduino GPIO number 17)
|
||||
IO2 <-> P1.02 (Arduino GPIO number 34)
|
||||
IO3 <-> P0.21 (Arduino GPIO number 21)
|
||||
IO4 <-> P0.04 (Arduino GPIO number 4)
|
||||
IO5 <-> P0.09 (Arduino GPIO number 9)
|
||||
IO6 <-> P0.10 (Arduino GPIO number 10)
|
||||
IO7 <-> P0.28 (Arduino GPIO number 28)
|
||||
SW1 <-> P0.01 (Arduino GPIO number 1)
|
||||
A0 <-> P0.04/AIN2 (Arduino Analog A2
|
||||
A1 <-> P0.31/AIN7 (Arduino Analog A7
|
||||
SPI_CS <-> P0.26 (Arduino GPIO number 26)
|
||||
*/
|
||||
|
||||
// RAK4630 LoRa module
|
||||
|
||||
/* Setup of the SX1262 LoRa module ( https://docs.rakwireless.com/Product-Categories/WisBlock/RAK4631/Datasheet/ )
|
||||
|
||||
P1.10 NSS SPI NSS (Arduino GPIO number 42)
|
||||
P1.11 SCK SPI CLK (Arduino GPIO number 43)
|
||||
P1.12 MOSI SPI MOSI (Arduino GPIO number 44)
|
||||
P1.13 MISO SPI MISO (Arduino GPIO number 45)
|
||||
P1.14 BUSY BUSY signal (Arduino GPIO number 46)
|
||||
P1.15 DIO1 DIO1 event interrupt (Arduino GPIO number 47)
|
||||
P1.06 NRESET NRESET manual reset of the SX1262 (Arduino GPIO number 38)
|
||||
|
||||
Important for successful SX1262 initialization:
|
||||
|
||||
* Setup DIO2 to control the antenna switch
|
||||
* Setup DIO3 to control the TCXO power supply
|
||||
* Setup the SX1262 to use it's DCDC regulator and not the LDO
|
||||
* RAK4630 schematics show GPIO P1.07 connected to the antenna switch, but it should not be initialized, as DIO2 will do the
|
||||
control of the antenna switch
|
||||
|
||||
SO GPIO 39/TXEN MAY NOT BE DEFINED FOR SUCCESSFUL OPERATION OF THE SX1262 - TG
|
||||
|
||||
*/
|
||||
|
||||
#define DETECTION_SENSOR_EN 4
|
||||
|
||||
#define USE_SX1262
|
||||
#define SX126X_CS (42)
|
||||
#define SX126X_DIO1 (47)
|
||||
#define SX126X_BUSY (46)
|
||||
#define SX126X_RESET (38)
|
||||
// #define SX126X_TXEN (39)
|
||||
// #define SX126X_RXEN (37)
|
||||
#define SX126X_POWER_EN (37)
|
||||
// DIO2 controlls an antenna switch and the TCXO voltage is controlled by DIO3
|
||||
#define SX126X_DIO2_AS_RF_SWITCH
|
||||
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
||||
|
||||
// Testing USB detection
|
||||
#define NRF_APM
|
||||
|
||||
// enables 3.3V periphery like GPS or IO Module
|
||||
// Do not toggle this for GPS power savings
|
||||
#define PIN_3V3_EN (34)
|
||||
|
||||
// RAK1910 GPS module
|
||||
// If using the wisblock GPS module and pluged into Port A on WisBlock base
|
||||
// IO1 is hooked to PPS (pin 12 on header) = gpio 17
|
||||
// IO2 is hooked to GPS RESET = gpio 34, but it can not be used to this because IO2 is ALSO used to control 3V3_S power (1 is on).
|
||||
// Therefore must be 1 to keep peripherals powered
|
||||
// Power is on the controllable 3V3_S rail
|
||||
// #define PIN_GPS_RESET (34)
|
||||
// #define PIN_GPS_EN PIN_3V3_EN
|
||||
#define PIN_GPS_PPS (17) // Pulse per second input from the GPS
|
||||
|
||||
// On RAK2560 the GPS is be on a different UART
|
||||
// #define GPS_RX_PIN PIN_SERIAL2_RX
|
||||
// #define GPS_TX_PIN PIN_SERIAL2_TX
|
||||
// #define PIN_GPS_EN PIN_3V3_EN
|
||||
// Disable GPS
|
||||
#define MESHTASTIC_EXCLUDE_GPS 1
|
||||
// Define pin to enable GPS toggle (set GPIO to LOW) via user button triple press
|
||||
|
||||
// RAK12002 RTC Module
|
||||
#define RV3028_RTC (uint8_t)0b1010010
|
||||
|
||||
// RAK18001 Buzzer in Slot C
|
||||
// #define PIN_BUZZER 21 // IO3 is PWM2
|
||||
// NEW: set this via protobuf instead!
|
||||
|
||||
// Battery
|
||||
// The battery sense is hooked to pin A0 (5)
|
||||
#define BATTERY_PIN PIN_A0
|
||||
// and has 12 bit resolution
|
||||
#define BATTERY_SENSE_RESOLUTION_BITS 12
|
||||
#define BATTERY_SENSE_RESOLUTION 4096.0
|
||||
#undef AREF_VOLTAGE
|
||||
#define AREF_VOLTAGE 3.0
|
||||
#define VBAT_AR_INTERNAL AR_INTERNAL_3_0
|
||||
#define ADC_MULTIPLIER 1.73
|
||||
|
||||
#define HAS_RTC 1
|
||||
|
||||
#define HAS_ETHERNET 1
|
||||
|
||||
#define RAK_4631 1
|
||||
|
||||
#define HALF_UART_PIN PIN_SERIAL1_RX
|
||||
|
||||
#if defined(GPS_RX_PIN) && (GPS_RX_PIN == HALF_UART_PIN)
|
||||
#error pin 15 collision
|
||||
|
||||
#endif
|
||||
|
||||
#if defined(GPS_TX_PIN) && (GPS_RX_PIN == HALF_UART_PIN)
|
||||
#error pin 15 collision
|
||||
#endif
|
||||
|
||||
#define PIN_ETHERNET_RESET 21
|
||||
#define PIN_ETHERNET_SS PIN_EINK_CS
|
||||
#define ETH_SPI_PORT SPI1
|
||||
#define AQ_SET_PIN 10
|
||||
|
||||
#ifdef __cplusplus
|
||||
}
|
||||
#endif
|
||||
|
||||
/*----------------------------------------------------------------------------
|
||||
* Arduino objects - C++ only
|
||||
*----------------------------------------------------------------------------*/
|
||||
|
||||
#endif
|
||||
@ -34,7 +34,8 @@
|
||||
#include "WVariant.h"
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
extern "C"
|
||||
{
|
||||
#endif // __cplusplus
|
||||
|
||||
// Number of pins defined in PinDescription array
|
||||
@ -55,9 +56,9 @@ extern "C" {
|
||||
|
||||
#define LED_STATE_ON 1 // State when LED is litted
|
||||
|
||||
/*
|
||||
* Buttons
|
||||
*/
|
||||
/*
|
||||
* Buttons
|
||||
*/
|
||||
|
||||
#define PIN_BUTTON1 9 // Pin for button on E-ink button module or IO expansion
|
||||
#define BUTTON_NEED_PULLUP
|
||||
@ -77,14 +78,14 @@ extern "C" {
|
||||
#define PIN_A6 (0xff)
|
||||
#define PIN_A7 (0xff)
|
||||
|
||||
static const uint8_t A0 = PIN_A0;
|
||||
static const uint8_t A1 = PIN_A1;
|
||||
static const uint8_t A2 = PIN_A2;
|
||||
static const uint8_t A3 = PIN_A3;
|
||||
static const uint8_t A4 = PIN_A4;
|
||||
static const uint8_t A5 = PIN_A5;
|
||||
static const uint8_t A6 = PIN_A6;
|
||||
static const uint8_t A7 = PIN_A7;
|
||||
static const uint8_t A0 = PIN_A0;
|
||||
static const uint8_t A1 = PIN_A1;
|
||||
static const uint8_t A2 = PIN_A2;
|
||||
static const uint8_t A3 = PIN_A3;
|
||||
static const uint8_t A4 = PIN_A4;
|
||||
static const uint8_t A5 = PIN_A5;
|
||||
static const uint8_t A6 = PIN_A6;
|
||||
static const uint8_t A7 = PIN_A7;
|
||||
#define ADC_RESOLUTION 14
|
||||
|
||||
// Other pins
|
||||
@ -92,7 +93,7 @@ static const uint8_t A7 = PIN_A7;
|
||||
#define PIN_NFC1 (9)
|
||||
#define PIN_NFC2 (10)
|
||||
|
||||
static const uint8_t AREF = PIN_AREF;
|
||||
static const uint8_t AREF = PIN_AREF;
|
||||
|
||||
/*
|
||||
* Serial interfaces
|
||||
@ -100,9 +101,9 @@ static const uint8_t AREF = PIN_AREF;
|
||||
#define PIN_SERIAL1_RX (15)
|
||||
#define PIN_SERIAL1_TX (16)
|
||||
|
||||
// Connected to Serial 2
|
||||
#define PIN_SERIAL2_RX (19)
|
||||
#define PIN_SERIAL2_TX (20)
|
||||
// Connected to Jlink CDC
|
||||
#define PIN_SERIAL2_RX (8)
|
||||
#define PIN_SERIAL2_TX (6)
|
||||
|
||||
/*
|
||||
* SPI Interfaces
|
||||
@ -117,14 +118,14 @@ static const uint8_t AREF = PIN_AREF;
|
||||
#define PIN_SPI1_MOSI (30) // (0 + 30)
|
||||
#define PIN_SPI1_SCK (3) // (0 + 3)
|
||||
|
||||
static const uint8_t SS = 42;
|
||||
static const uint8_t MOSI = PIN_SPI_MOSI;
|
||||
static const uint8_t MISO = PIN_SPI_MISO;
|
||||
static const uint8_t SCK = PIN_SPI_SCK;
|
||||
static const uint8_t SS = 42;
|
||||
static const uint8_t MOSI = PIN_SPI_MOSI;
|
||||
static const uint8_t MISO = PIN_SPI_MISO;
|
||||
static const uint8_t SCK = PIN_SPI_SCK;
|
||||
|
||||
/*
|
||||
* eink display pins
|
||||
*/
|
||||
/*
|
||||
* eink display pins
|
||||
*/
|
||||
|
||||
#define PIN_EINK_CS (0 + 26)
|
||||
#define PIN_EINK_BUSY (0 + 4)
|
||||
@ -158,44 +159,44 @@ static const uint8_t SCK = PIN_SPI_SCK;
|
||||
#define EXTERNAL_FLASH_DEVICES IS25LP080D
|
||||
#define EXTERNAL_FLASH_USE_QSPI
|
||||
|
||||
/* @note RAK5005-O GPIO mapping to RAK4631 GPIO ports
|
||||
RAK5005-O <-> nRF52840
|
||||
IO1 <-> P0.17 (Arduino GPIO number 17)
|
||||
IO2 <-> P1.02 (Arduino GPIO number 34)
|
||||
IO3 <-> P0.21 (Arduino GPIO number 21)
|
||||
IO4 <-> P0.04 (Arduino GPIO number 4)
|
||||
IO5 <-> P0.09 (Arduino GPIO number 9)
|
||||
IO6 <-> P0.10 (Arduino GPIO number 10)
|
||||
IO7 <-> P0.28 (Arduino GPIO number 28)
|
||||
SW1 <-> P0.01 (Arduino GPIO number 1)
|
||||
A0 <-> P0.04/AIN2 (Arduino Analog A2
|
||||
A1 <-> P0.31/AIN7 (Arduino Analog A7
|
||||
SPI_CS <-> P0.26 (Arduino GPIO number 26)
|
||||
*/
|
||||
/* @note RAK5005-O GPIO mapping to RAK4631 GPIO ports
|
||||
RAK5005-O <-> nRF52840
|
||||
IO1 <-> P0.17 (Arduino GPIO number 17)
|
||||
IO2 <-> P1.02 (Arduino GPIO number 34)
|
||||
IO3 <-> P0.21 (Arduino GPIO number 21)
|
||||
IO4 <-> P0.04 (Arduino GPIO number 4)
|
||||
IO5 <-> P0.09 (Arduino GPIO number 9)
|
||||
IO6 <-> P0.10 (Arduino GPIO number 10)
|
||||
IO7 <-> P0.28 (Arduino GPIO number 28)
|
||||
SW1 <-> P0.01 (Arduino GPIO number 1)
|
||||
A0 <-> P0.04/AIN2 (Arduino Analog A2
|
||||
A1 <-> P0.31/AIN7 (Arduino Analog A7
|
||||
SPI_CS <-> P0.26 (Arduino GPIO number 26)
|
||||
*/
|
||||
|
||||
// RAK4630 LoRa module
|
||||
// RAK4630 LoRa module
|
||||
|
||||
/* Setup of the SX1262 LoRa module ( https://docs.rakwireless.com/Product-Categories/WisBlock/RAK4631/Datasheet/ )
|
||||
/* Setup of the SX1262 LoRa module ( https://docs.rakwireless.com/Product-Categories/WisBlock/RAK4631/Datasheet/ )
|
||||
|
||||
P1.10 NSS SPI NSS (Arduino GPIO number 42)
|
||||
P1.11 SCK SPI CLK (Arduino GPIO number 43)
|
||||
P1.12 MOSI SPI MOSI (Arduino GPIO number 44)
|
||||
P1.13 MISO SPI MISO (Arduino GPIO number 45)
|
||||
P1.14 BUSY BUSY signal (Arduino GPIO number 46)
|
||||
P1.15 DIO1 DIO1 event interrupt (Arduino GPIO number 47)
|
||||
P1.06 NRESET NRESET manual reset of the SX1262 (Arduino GPIO number 38)
|
||||
P1.10 NSS SPI NSS (Arduino GPIO number 42)
|
||||
P1.11 SCK SPI CLK (Arduino GPIO number 43)
|
||||
P1.12 MOSI SPI MOSI (Arduino GPIO number 44)
|
||||
P1.13 MISO SPI MISO (Arduino GPIO number 45)
|
||||
P1.14 BUSY BUSY signal (Arduino GPIO number 46)
|
||||
P1.15 DIO1 DIO1 event interrupt (Arduino GPIO number 47)
|
||||
P1.06 NRESET NRESET manual reset of the SX1262 (Arduino GPIO number 38)
|
||||
|
||||
Important for successful SX1262 initialization:
|
||||
Important for successful SX1262 initialization:
|
||||
|
||||
* Setup DIO2 to control the antenna switch
|
||||
* Setup DIO3 to control the TCXO power supply
|
||||
* Setup the SX1262 to use it's DCDC regulator and not the LDO
|
||||
* RAK4630 schematics show GPIO P1.07 connected to the antenna switch, but it should not be initialized, as DIO2 will do the
|
||||
control of the antenna switch
|
||||
* Setup DIO2 to control the antenna switch
|
||||
* Setup DIO3 to control the TCXO power supply
|
||||
* Setup the SX1262 to use it's DCDC regulator and not the LDO
|
||||
* RAK4630 schematics show GPIO P1.07 connected to the antenna switch, but it should not be initialized, as DIO2 will do the
|
||||
control of the antenna switch
|
||||
|
||||
SO GPIO 39/TXEN MAY NOT BE DEFINED FOR SUCCESSFUL OPERATION OF THE SX1262 - TG
|
||||
SO GPIO 39/TXEN MAY NOT BE DEFINED FOR SUCCESSFUL OPERATION OF THE SX1262 - TG
|
||||
|
||||
*/
|
||||
*/
|
||||
|
||||
#define DETECTION_SENSOR_EN 4
|
||||
|
||||
@ -228,18 +229,9 @@ SO GPIO 39/TXEN MAY NOT BE DEFINED FOR SUCCESSFUL OPERATION OF THE SX1262 - TG
|
||||
// #define PIN_GPS_EN PIN_3V3_EN
|
||||
#define PIN_GPS_PPS (17) // Pulse per second input from the GPS
|
||||
|
||||
// On RAK2560 the GPS is be on a different UART
|
||||
#ifdef HAS_RAKPROT
|
||||
// #define GPS_RX_PIN PIN_SERIAL2_RX
|
||||
// #define GPS_TX_PIN PIN_SERIAL2_TX
|
||||
// #define PIN_GPS_EN PIN_3V3_EN
|
||||
// Disable GPS
|
||||
#define MESHTASTIC_EXCLUDE_GPS 1
|
||||
#else
|
||||
// Enable GPS
|
||||
#define GPS_RX_PIN PIN_SERIAL1_RX
|
||||
#define GPS_TX_PIN PIN_SERIAL1_TX
|
||||
#endif
|
||||
|
||||
// Define pin to enable GPS toggle (set GPIO to LOW) via user button triple press
|
||||
|
||||
// RAK12002 RTC Module
|
||||
@ -266,21 +258,6 @@ SO GPIO 39/TXEN MAY NOT BE DEFINED FOR SUCCESSFUL OPERATION OF THE SX1262 - TG
|
||||
|
||||
#define RAK_4631 1
|
||||
|
||||
#ifdef HAS_RAKPROT
|
||||
|
||||
#define HALF_UART_PIN PIN_SERIAL1_RX
|
||||
|
||||
#if defined(GPS_RX_PIN) && (GPS_RX_PIN == HALF_UART_PIN)
|
||||
#error pin 15 collision
|
||||
|
||||
#endif
|
||||
|
||||
#if defined(GPS_TX_PIN) && (GPS_RX_PIN == HALF_UART_PIN)
|
||||
#error pin 15 collision
|
||||
#endif
|
||||
|
||||
#endif
|
||||
|
||||
#define PIN_ETHERNET_RESET 21
|
||||
#define PIN_ETHERNET_SS PIN_EINK_CS
|
||||
#define ETH_SPI_PORT SPI1
|
||||
|
||||
Loading…
Reference in New Issue
Block a user