* PMSA0031 sensors require ~3secs before coming up on I2C
As reported by @MALAONE1 and debugged by @shodan8192 , PMSA0031s
on a RAK4631 take 3 seconds before they can become detectable on I2c.
Add a delay(4000) before I2C scan if the air quality sensor pin
is defined.
Fixes https://github.com/meshtastic/firmware/issues/3690
* Remove 4 second wait and rescan during air quality init for the sensor
* works without but this triggers my OCD
---------
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
QMC5883L and HMC5883L are 3-axis compasses which are often confused.
As reported by @Africmod, we had the wrong I2C address for the QMC5883L.
This patch fixes the address and adds its HMC5883L so we keep info
about both.
Fixes https://github.com/meshtastic/firmware/issues/4144
* tryfix #4384 - don't assume we want that functionality if the Accelerometer was found. This is only for T-Watch
* Add config.display.wake_on_tap_or_motion default to RAK
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
(from src/extra_variants/README.md)
This directory tree is designed to solve two problems.
- The ESP32 arduino/platformio project doesn't support the nice "if initVariant() is found, call that after init" behavior of the nrf52 builds (they use initVariant() internally).
- Over the years a lot of 'board specific' init code has been added to init() in main.cpp. It would be great to have a general/clean mechanism to allow developers to specify board specific/unique code in a clean fashion without mucking in main.
So we are borrowing the initVariant() ideas here (by using weak gcc references). You can now define lateInitVariant() if your board needs it.
If you'd like a board specific variant to be run, add the variant.cpp file to an appropriately named
subdirectory and check for \_VARIANT_boardname in the cpp file (so that your code is only built for your board).
You'll need to define \_VARIANT_boardname in your corresponding variant.h file.
See existing boards for examples.
This approach has no added runtime cost.
No need for _V05 and _V03 definitions - I think there was a slight misunderstanding
on how variant files are supposed to _decrease_ #ifdef code in the cpp files.
* Update main.cpp
Add in TCXO_OPTIONAL variable for tcxoVoltage and a double-check for working in both modes.
* Update SX126xInterface.cpp
Make a change to the tcxoVoltage setting so that TCXO_OPTIONAL works if defined.
* Update variant.h
Added define for TCXO_OPTIONAL and the tcxoVoltage variable.
Added detail on the compatible boards.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
After the recent GPS power work we have an clear set of
definitions for turning GPS on and off. Rather than manipulating
specific heltec tracker-related pins in main setu, the relevant
power management code in the GPS module will turn things
on/off later as needed.
* Re-implement PKI from #1509
co-authored-by: edinnen <ethanjdinnen@protonmail.com>
* Set the key lengnth to actually make PKI work.
* Remove unused variable and initialize keys to null
* move printBytes() to meshUtils
* Don't reset PKI key son reboot unless needed.
* Remove double encryption for PKI messages
* Cleanup encrypt logic
* Add the MESHTASTIC_EXCLUDE_PKI option, and set it for minimal builds. Required for STM32 targets for now.
* Use SHA-256 for PKI key hashing, and add MESHTASTIC_EXCLUDE_PKI_KEYGEN for STM32
* Fix a crash when node is null
* Don't send PKI encrypted packets while licensed
* use chIndex 8 for PKI
* Don't be so clever, that you corrupt incoming packets
* Pass on channel 8 for now
* Typo
* Lock keys once non-zero
* We in fact need 2 scratch buffers, to store the encrypted bytes, unencrypted bytes, and decoded protobuf.
* Lighter approach to retaining known key
* Attach the public key to PKI decrypted packets in device memory
* Turn PKI back off for STM32 :(
* Don't just memcp over a protobuf
* Don't PKI encrypt nodeinfo packets
* Add a bit more memory logging around nodeDB
* Use the proper macro to refer to NODENUM_BROADCAST
* Typo fix
* Don't PKI encrypt ROUTING (naks and acks)
* Adds SecurityConfig protobuf
* Add admin messages over PKI
* Disable PKI for the WIO-e5
* Add MINIMUM_SAFE_FREE_HEAP macro and set to safe 1.5k
* Add missed "has_security"
* Add the admin_channel_enabled option
* STM32 again
* add missed configuration.h at the top of files
* Add EXCLUDE_TZ and RTC
* Enable PKI build on STM32 once again
* Attempt 1 at moving PKI to aes-ccm
* Fix buffers for encrypt/decrypt
* Eliminate unused aes variable
* Add debugging lines
* Set hash to 0 for PKI
* Fix debug lines so they don't print pointers.
* logic fix and more debug
* Rather important typo
* Check for short packets before attempting decrypt
* Don't forget to give cryptoEngine the keys!
* Use the right scratch buffer
* Cleanup
* moar cleanups
* Minor hardening
* Remove some in-progress stuff
* Turn PKI back off on STM32
* Return false
* 2.5 protos
* Sync up protos
* Add initial cryptography test vector tests
* re-add MINIMUM_SAFE_FREE_HEAP
* Housekeeping and comment fixes
* Add explanatory comment about weak dh25519 keys
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Update sensor drive and low power features.
* Update ST7789 TFT control logic.
* Update Heltec nRF board low power features.
* Update the GPS UART port pointer
* Turn off vscode cmake prompt - we don't use cmake on meshtastic
* Add rak4631_dap variant for debugging with NanoDAP debug probe device.
* The rak device can also run freertos (which is underneath nrf52 arduino)
* Add semihosting support for nrf52840 devices
Initial platformio.ini file only supports rak4630
Default to non TCP for the semihosting log output for now...
Fixes https://github.com/meshtastic/firmware/issues/4135
* powermon WIP (for https://github.com/meshtastic/firmware/issues/4136 )
* oops - mean't to mark the _dbg variant as an 'extra' board.
* powermon wip
* Make serial port on wio-sdk-wm1110 board work
By disabling the (inaccessible) adafruit USB
* Instrument (radiolib only for now) lora for powermon
per https://github.com/meshtastic/firmware/issues/4136
* powermon gps support
https://github.com/meshtastic/firmware/issues/4136
* Add CPU deep and light sleep powermon states
https://github.com/meshtastic/firmware/issues/4136
* Change the board/swversion bootstring so it is a new "structured" log msg.
* powermon wip
* add example script for getting esp S3 debugging working
Not yet used but I didn't want these nasty tricks to get lost yet.
* Add PowerMon reporting for screen and bluetooth pwr.
* make power.powermon_enables config setting work.
* update to latest protobufs
* fix bogus shellcheck warning
* make powermon optional (but default enabled because tiny and no runtime impact)
* tell vscode, if formatting, use whatever our trunk formatter wants
without this flag if the user has set some other formatter (clang)
in their user level settings, it will be looking in the wrong directory
for the clang options (we want the options in .trunk/clang)
Note: formatOnSave is true in master, which means a bunch of our older
files are non compliant and if you edit them it will generate lots of
formatting related diffs. I guess I'll start letting that happen with
my future commits ;-).
* add PowerStress module
* nrf52 arduino is built upon freertos, so let platformio debug it
* don't accidentally try to Segger ICE if we are using another ICE
* clean up RedirectablePrint::log so it doesn't have three very different implementations inline.
* remove NoopPrint - it is no longer needed
* when talking to API clients via serial, don't turn off log msgs instead encapsuate them
* fix the build - would loop forever if there were no files to send
* don't use Segger code if not talking to a Segger debugger
* when encapsulating logs, make sure the strings always has nul terminators
* nrf52 soft device will watchdog if you use ICE while BT on...
so have debugger disable bluetooth.
* Important to not print debug messages while writing to the toPhone scratch buffer
* don't include newlines if encapsulating log records as protobufs
* update to latest protobufs (needed for powermon goo)
* PowerStress WIP
* for #4154 and #4136 add concept of dependent gpios...
Which is currently only tested with the LED but eventually
will be used for shared GPIO/screen power rail enable
and LED forcing (which is a sanity check in the power stress
testing)
* fix linter warning
* Transformer is a better name for the LED input > operation > output classes
* PMW led changes to work on esp32-s3
* power stress improvements
* allow ble logrecords to be fetched either by NOTIFY or INDICATE ble types
This allows 'lossless' log reading. If client has requested INDICATE
(rather than NOTIFY) each log record emitted via log() will have to fetched
by the client device before the meshtastic node can continue.
* Fix serious problem with nrf52 BLE logging.
When doing notifies of LogRecords it is important to use the
binary write routines - writing using the 'string' write won't work.
Because protobufs can contain \0 nuls inside of them which if being
parsed as a string will cause only a portion of the protobuf to be sent.
I noticed this because some log messages were not getting through.
* fix gpio transformer stuff to work correctly with LED_INVERTED
Thanks @todd-herbert for noticing this and the great stack trace.
The root cause was that I had accidentially shadowed outPin in a subclass
with an unneeded override. It would break on any board that had inverted
LED power.
fixes
https://github.com/meshtastic/firmware/pull/4230#pullrequestreview-2217389099
* Support driving multiple output gpios from one input.
While investigating https://github.com/meshtastic/firmware/pull/4230#pullrequestreview-2217389099
I noticed in variant.h that there are now apparently newer TBEAMs than mine
that have _both_ a GPIO based power LED and the PMU based LED. Add a splitter
so that we can drive two output GPIOs from one logical signal.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
While working on #4378 I noticed a funny problem: the blinking system
LED was on during deep-sleep. Initially I thought it was some weird
sleep hw config thing but it turns out it was easier but more pervasive.
We had two different preprocessor symbols which both meant approximately the same
thing LED_INVERTED and LED_STATE_ON (though their polarity was opposite).
Some variant files were setting one, others were setting the other, and others were
setting both. heh.
In the case of the board I was testing (seeed tracker wio 1100) it was only setting one
and the default behavior for the other (for all boards) was incorrect. So I did a grep
and it seems like LED_STATE_ON was used more often, so I kept that one and removed
LED_INVERTED everywhere.
* Make SPI frequency configurable on Native
* Make the tophone queue size configurable for Portduino
* The modified SPISettings must be configured in setup(), after config.yaml is processed
* make MeshService a pointer, so we can configure MAX_RX_TOPHONE at run time
* Got a little over excited with refactoring
* Silence a warning
* Make STM compile again and update toolchain. The binary is too big for the flash. WIP
* Making progress with OSFS, still WIP
* more progress, still too big. Adding RAK3172 to the equasion
* Make STM compile again and update toolchain. The binary is too big for the flash. WIP
* Making progress with OSFS, still WIP
* more progress, still too big. Adding RAK3172 to the equasion
* still too big
* minimize build
* trunk fmt
* fix a couple of symbol clashes
* trunk fmt
* down to 101% with a release vs. debug build and omitting the flash strings
* fix compilation
* fix compilation once more
* update protobufs linkage
* - Toolchain updated
- Fixed macro error
* silence compiler warning
note: do something about this assert...
* new toolkit and fix Power.cpp
* STM32WL make it fit (#4330)
* Add option to exclude I2C parts
The I2C hals and related code uses a significant amount of flash space and aren't required for a basic node.
* Add option to disable Admin and NodeInfo modules
Disabled by default in minimal build. This saves a significant amount of flash
* Disable unused hals
These use up significant flash
* Add float support for printf for debugging
Makes serial look nice for debugging
* This breaks my build for some reason
* These build flags can save a bit of flash
* Don't disable NodeInfo and Admin modules in minimal build
They fit in flash
* Don't include printf float support by default
Only useful for debugging
---------
Co-authored-by: Adam Lawson <dev@goshawk22.uk>
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Adam Lawson <dev@goshawk22.uk>
* Tidy variant.h and pins_arduino.h (VME213)
* Wait for peripherals to stabilize after enabling I2C power
The 3.3V power for the I2C "quick link" connector is from Ve_3V3
* Turn off vscode cmake prompt - we don't use cmake on meshtastic
* Add rak4631_dap variant for debugging with NanoDAP debug probe device.
* The rak device can also run freertos (which is underneath nrf52 arduino)
* Add semihosting support for nrf52840 devices
Initial platformio.ini file only supports rak4630
Default to non TCP for the semihosting log output for now...
Fixes https://github.com/meshtastic/firmware/issues/4135
* powermon WIP (for https://github.com/meshtastic/firmware/issues/4136 )
* oops - mean't to mark the _dbg variant as an 'extra' board.
* powermon wip
* Make serial port on wio-sdk-wm1110 board work
By disabling the (inaccessible) adafruit USB
* Instrument (radiolib only for now) lora for powermon
per https://github.com/meshtastic/firmware/issues/4136
* powermon gps support
https://github.com/meshtastic/firmware/issues/4136
* Add CPU deep and light sleep powermon states
https://github.com/meshtastic/firmware/issues/4136
* Change the board/swversion bootstring so it is a new "structured" log msg.
* powermon wip
* add example script for getting esp S3 debugging working
Not yet used but I didn't want these nasty tricks to get lost yet.
* Add PowerMon reporting for screen and bluetooth pwr.
* make power.powermon_enables config setting work.
* update to latest protobufs
* fix bogus shellcheck warning
* make powermon optional (but default enabled because tiny and no runtime impact)
* tell vscode, if formatting, use whatever our trunk formatter wants
without this flag if the user has set some other formatter (clang)
in their user level settings, it will be looking in the wrong directory
for the clang options (we want the options in .trunk/clang)
Note: formatOnSave is true in master, which means a bunch of our older
files are non compliant and if you edit them it will generate lots of
formatting related diffs. I guess I'll start letting that happen with
my future commits ;-).
* add PowerStress module
* nrf52 arduino is built upon freertos, so let platformio debug it
* don't accidentally try to Segger ICE if we are using another ICE
* clean up RedirectablePrint::log so it doesn't have three very different implementations inline.
* remove NoopPrint - it is no longer needed
* when talking to API clients via serial, don't turn off log msgs instead encapsuate them
* fix the build - would loop forever if there were no files to send
* don't use Segger code if not talking to a Segger debugger
* when encapsulating logs, make sure the strings always has nul terminators
* nrf52 soft device will watchdog if you use ICE while BT on...
so have debugger disable bluetooth.
* Important to not print debug messages while writing to the toPhone scratch buffer
* don't include newlines if encapsulating log records as protobufs
* update to latest protobufs (needed for powermon goo)
* PowerStress WIP
* fix linter warning
* clean up RedirectablePrint::log so it doesn't have three very different implementations inline.
* remove NoopPrint - it is no longer needed
* when talking to API clients via serial, don't turn off log msgs instead encapsuate them
* fix the build - would loop forever if there were no files to send
* don't use Segger code if not talking to a Segger debugger
* when encapsulating logs, make sure the strings always has nul terminators
* nrf52 soft device will watchdog if you use ICE while BT on...
so have debugger disable bluetooth.
* Important to not print debug messages while writing to the toPhone scratch buffer
* don't include newlines if encapsulating log records as protobufs
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Move static functions into Screen.h, show compass during calibration
* Move to _fontHeight macro to avoid collision
* Move some alert functions to new alert handler
* Catch missed reboot code
* ESP32 fixes
* Bump esp8266-oled-ssd1306
* Fixes for when a device has no screen
* Use new startAlert(char*) helper class
* Add EINK bits back to alert handling
* Add noop class for no-display devices
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* WIP log characteristic
* Bluetooth logging plumbing
* Characteristic
* Callback
* Check for nullptr
* Esp32 bluetooth impl
* Formatting
* Add thread name and log level
* Add settings guard
* Remove comments
* Field name
* Fixes esp32
* Open it up
* Whoops
* Move va_end past our logic
