remove newline from logging statements in code. The LOG_* functions will now magically add it at the end.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Uplink DMs not to us if MQTT encryption enabled
* Only really need to try uplinking encrypted packet if MQTT encryption is enabled
* Add log about publishing nothing when packet is not decrypted and encryption_enabled is false
* Improve comment
* preliminary Othernet Dreamcatcher 2206 Support
Need to adapt to 2301 final version
* second target for latest revision
* preliminary Othernet Dreamcatcher 2206 Support
Need to adapt to 2301 final version
* second target for latest revision
* preliminary Othernet Dreamcatcher 2206 Support
Need to adapt to 2301 final version
* second target for latest revision
* address comments
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Add stub health telemetry module
* Add detection for MAX30102 Health Sensor
It lives on I2C bus at 0x57, which conflicts with an existing
sensor. Add code to check the PARTID register for its response 0x15
per spec.
* Add detection for MLX90614
An IR Temperature sensor suitable for livestock monitoring.
* Add libraries for MLX90614 and MAX30102 sensors
* Fix Trunk
* Add support for MLX90614 IR Temperature Sensor
* Add support for MAX30102 (Temperature)
* Make it build - our first HealthTelemetry on the mesh.
If a MAX30102 is connected, its temperature will be sent to the
mesh as HealthTelemetry.
* Add spo2 and heart rate calculations to MAX30102
* Switch MLX90614 to Adafruit library
Sparkfun was having fun with SDA/SCL variables which we can avoid
by switching to this highly similar library.
* Enable HealthTelemetry if MLX90614 detected
* Change MLX90614 emissivity for human skin.
* Add health screen!
* Remove autogenerated file from branch
* Preparing for review
* Fix MeshService master sync from before.
* Prepare for review
* For the americans
* Fix native build
* Fix for devices with no screen
* Remove extra log causing issues
---------
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Fix LED pinout for T-Echo board marked v1.0, date 2021-6-28
* Merge PR #420
* Fixed double and missing Default class.
* Use correct format specifier and fixed typo.
* Removed duplicate code.
* Fix error: #if with no expression
* Fix warning: extra tokens at end of #endif directive.
* Fix antenna switching logic. Complementary-pin control logic is required on the rp2040-lora board.
* Fix deprecated macros.
* Set RP2040 in dormant mode when deep sleep is triggered.
* Fix array out of bounds read.
* Admin key count needs to be set otherwise the key will be zero loaded after reset.
* Don't reset the admin key size when loading defaults. Preserve an existing key in config if possible.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
There are three different frequencies available for Meshtastic
in the Philippines, each with pros and cons:
433 - 434.7 MHz <10 mW erp
868 - 869.4 MHz <25 mW erp
915 - 918 MHz <250 mW EIRP, no external antennna allowed
Philippines may also use LORA_24 unrestricted at up to 10mW, or up to
250mW if there is no external antennna.
Frequency rules in the Philippines are determined by aggregating the
information in laws, following the circulars referenced in the
[National Radio Frequency Allocation Table (NRFAT)](https://ntc.gov.ph/wp-content/uploads/2022/frequencyallocations/NRFAT_Rev_2020.pdf)
and then circulars that amend the circulars referenced in the NRFAT.
A full description of the regulatory basis can be found in the github issue:
https://github.com/meshtastic/firmware/issues/4948#issuecomment-2394926135
For 433MHz and 868MHz we refer to the Low Power Equipment rules for
"Non-specific Short Range Devices, Telemetry, Telecommand, Alarms,
Data In General and Other Similar Applications.".
For 915MHz and Wireless Data Network Services indoor device rules.
A device approved by the NTC is required for any use of Meshtastic
in the Philippines.
fixes https://github.com/meshtastic/firmware/issues/4948
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Previously our debug message for screens blandly stated
"Module wants a UI Frame"
This patch replaces the word Module with the name of the Module
in need of a frame a frame, enhancing debugging ability.
GetTimeSinceMeshPacket was duplicated in PowerTelemetry and
EnvironmentalTelemetry, albeit one had a cooler name than the other.
As we add HealthTelemetry, to avoid creating a third instance of
this method, let's move it somewhere that makese sense.
Adds a new method GetTimeSinceMeshPacket to MeshService and updates
EnvironmentTelemetry and PowerTelemetry to use it.
* added up to 3 channels via userprefs
* added up to 3 channels via userprefs
* added up to 3 channels via userprefs
* trunk fmt
* Added USERPREFS for GPS MODE
* * Adding the -Wcast-align compilation flag for
the rp2040.
* * Some rework to use a struct to access radio data
* Buffer will not be accessed by arithmetic pointer anymore
* * Remplace arithmetic pointer to avoid Warning
* * Avoid 2 little artitmetic pointer
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Potential fix for bad Rx performance on T1000-E
* validate and refactor RF switching, eliminate godmode
---------
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
