* T1000-E Peripherals
- enable intelligent charge controller signals
- enable Accelerometer
- enable internal I2C bus
- provide Power to Accelerometer
* POC Accelerometer Code (wakeScreen is moot for that device, just test if the driver works)
* fix building without the sensor
Determines if the given IP address is a private address, i.e. not routable on the public internet.
These are the ranges: 127.0.0.1, 10.0.0.0-10.255.255.255, 172.16.0.0-172.31.255.255, 192.168.0.0-192.168.255.255.
If so, allow MQTT publication the same as existing localhost support.
remove newline from logging statements in code. The LOG_* functions will now magically add it at the end.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Uplink DMs not to us if MQTT encryption enabled
* Only really need to try uplinking encrypted packet if MQTT encryption is enabled
* Add log about publishing nothing when packet is not decrypted and encryption_enabled is false
* Improve comment
* Refactor and consolidate windowing logic
* Trunk
* Fixes
* More
* Fix braces and remove unused now variables.
There was a brace in src/mesh/RadioLibInterface.cpp that was breaking
compile on some architectures.
Additionally, there were some brace errors in
src/modules/Telemetry/AirQualityTelemetry.cpp
src/modules/Telemetry/EnvironmentTelemetry.cpp
src/mesh/wifi/WiFiAPClient.cpp
Move throttle include in WifiAPClient.cpp to top.
Add Default.h to sleep.cpp
rest of files just remove unused now variables.
* Remove a couple more meows
---------
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Don't filter PKI packets just for being encrypted.
* Add ok_to_mqtt config and bit
* Bitfield
* Adjust dontmqttmebro logic.
* Manipulate bitfield only in router.cpp
* Want_ack is not want_response
* Bitfield macros
* Use new Bitfield macro in MQTT.cpp
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Make SPI frequency configurable on Native
* Make the tophone queue size configurable for Portduino
* The modified SPISettings must be configured in setup(), after config.yaml is processed
* make MeshService a pointer, so we can configure MAX_RX_TOPHONE at run time
* Got a little over excited with refactoring
* Silence a warning
* protobufs
* initial mods, not tested
* manual telem packet creation, compiles.
* add gust and lull computation
* telem packet is getting fired off
* new pb ?
* pb and gust lull
* need to set the variant type for it to work.
* add gust and lull to mqtt json output.
* parse bat voltage and cap voltage and send the larger of the two in telem packet
also use the new ws85 serial mode (6). must set it with cli. : meshtastic --set serial.mode 6
* set hard coded average/transmit interval to 5 minutes.
* proper direction averging with trig.
* Update protobufs
* sweep some crud
* read in 512 bytes at a time and break and clear serial input if we got wind data
* factor out sendTelemetry function
* Revert "factor out sendTelemetry function"
This reverts commit b61ba1a3c5.
* Reapply "factor out sendTelemetry function"
This reverts commit d0af9cfd7d.
* update protobufs
* put WS85 Serial2 is tcho and canaryone exclusion #ifdef
* include GeoCoord.h so dr-dev will compile.
* remove old TODO comment.
* breakout WS85 serial operation to it's own function called processWXSerial()
* canaryone and t-echo exclusion for Serial2
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* MESHTASTIC_EXCLUDE_WIFI and HAS_WIFI cleanup...
Our code was checking HAS_WIFI and the new MESHTASTIC_EXCLUDE_WIFI
flags in various places (even though EXCLUDE_WIFI forces HAS_WIFI
to 0). Instead just check HAS_WIFI, only use EXCLUDE_WIFI inside
configuration.h
* cleanup: use HAS_NETWORKING instead of HAS_WIFI || HAS_ETHERNET
We already had HAS_NETWORKING as flag in MQTT to mean 'we have
tcpip'. Generallize that and move it into configuration.h so that
we can use it elsewhere.
* Use #pragma once, because supported by gcc and all modern compilers
instead of #ifdef DOTHFILE_H etc...
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* Fix type of nodeNum
Type of nodeNum is NodeNum, not uint
* typo
fixed typo "resumeAdverising()"
* fix missing #include "time.h"
Missing include breaks compilation with gccnoneeabi 12.3.1 for nrf52 targets on windows hosts.
* change type uint to unsigned int
uint is not a standard type. Using uint breaks compilation with gccnoneeabi 12.3.1 for nRF52 targets on windows hosts.
* fix type of channel_num
Type of channel_num should be uint32_t (as this is the type of hash() and numChannels).
Using uint non-standard type uint breaks compilation with gccnoneeabi 12.3.1 for nRF52 targets on windows hosts.
* Update nrf52.ini
Default build type should be "release" as this is the default of platformio.
* Update GPS.cpp
uint to unsigned int
