* Rename message length headers and set payload max to 255
* Add MESHTASTIC_PKC_OVERHEAD
* compare to MESHTASTIC_HEADER_LENGTH
---------
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Thanks to user Goyath on Discord, we discovered that in Japan the
250mW radio level requires licensing, and 20mW is the practical
limit. We also discovered that a duty cycle of 10% is needed on
most frequencies.
CH 24-38 920.5-923.5 20mW no airtime restrictions
CH 39-61 923.5-928.1 20mW 10% airtime
* Make SPI frequency configurable on Native
* Make the tophone queue size configurable for Portduino
* The modified SPISettings must be configured in setup(), after config.yaml is processed
* make MeshService a pointer, so we can configure MAX_RX_TOPHONE at run time
* Got a little over excited with refactoring
* Silence a warning
* Cleanup - remove unused defines.
There were a number of defined variables that were carried over
from old code. - Removed.
Also a typo. - Fixed fix.
Also duplicate definitions of the number of seconds in a day.
-deduplicated.
* Cleanup - remove unused defines.
There were a number of defined variables that were carried over
from old code. - Removed.
Also a typo. - Fixed fix.
Also duplicate definitions of the number of seconds in a day.
-deduplicated.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
REGULATORY_GAIN is the total system gain in dBm to subtract from the configured Tx power, to remain within regulatory ERP limit for non-licensed operators.
This value should be set in variant.h and is PA gain + antenna gain (if system ships with an antenna).
This is similar to antenna_gain/NL80211_ATTR_WIPHY_ANTENNA_GAIN/NL80211_ATTR_REG_RULE_POWER_MAX_ANT_GAIN setting in Linux Regulatory/OpenWrt/mac80211/nl80211/iw.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Add REGULATORY_ prefix to LORA_REGIONCODE to prepare for more regulatory configuration options, and update comment block accordingly too.
Signed-off-by: Andrew Yong <me@ndoo.sg>
* Fix type of nodeNum
Type of nodeNum is NodeNum, not uint
* typo
fixed typo "resumeAdverising()"
* fix missing #include "time.h"
Missing include breaks compilation with gccnoneeabi 12.3.1 for nrf52 targets on windows hosts.
* change type uint to unsigned int
uint is not a standard type. Using uint breaks compilation with gccnoneeabi 12.3.1 for nRF52 targets on windows hosts.
* fix type of channel_num
Type of channel_num should be uint32_t (as this is the type of hash() and numChannels).
Using uint non-standard type uint breaks compilation with gccnoneeabi 12.3.1 for nRF52 targets on windows hosts.
* Update nrf52.ini
Default build type should be "release" as this is the default of platformio.
* Update GPS.cpp
uint to unsigned int
The TW region had now power limit set, so defaulted to 16dBm.
The relevant regulation is section 5.8.1 of the Low-power Radio-frequency Devices Technical Regulations, which notes the limits of 0.5W (27dBM) indoor or coastal, 1.0W (30dBM) outdoor.
This patch updates the power limit to 27dbM, using the the lower limit specified in the regulations to be conservative.
Regulation references:
https://www.ncc.gov.tw/english/files/23070/102_5190_230703_1_doc_C.PDF (latest English version)
https://gazette.nat.gov.tw/egFront/e_detail.do?metaid=147283 (latest Chinese version, February 2024)
The main use case for this will be to create a custom Heltec WiFi LoRa 32 V3 SG_923 variant, which will be pre-flashed and sent for regulatory approval for retail sale.
Signed-off-by: Andrew Yong <me@ndoo.sg>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add MaxNodes to Native
* It compiles...
* Convert nodedb to use new
* Closer but still broken.
* Finally working
* Remove unintended lines
* Don't include a pointer
* Capitalization matters.
* avoid rename in protocol regen
* When trimming the nodeDB, start with a cleanup
* Remove extra cleanupMeshDB() call for now
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Set `hop_start` in header to determine how many hops each packet traveled
* Set hopLimit of response according to hops used by request
* Identify neighbors based on `hopStart` and `hopLimit`
* NeighborInfo: get all packets and assume a default broadcast interval
* Add fail-safe in case node in between is running modified firmware
* Add `viaMQTT` and `hopsAway` to NodeInfo
* Replace `HOP_RELIABLE` with hopStart for repeated packet
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Mark packets received via MQTT and add option to ignore them
* Don't send packets received via MQTT back into MQTT
Generate implicit ACK for packets we as an MQTT gateway sent
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* Use startReceive() instead of startReceiveDutyCycleAuto()
* Add preamble detected IRQ
* Escape from 'freeze' state when packet should have been received
* Use RADIOLIB_GODMODE for access to clearIrqStatus
* SX126x: Better handling of false preamble detections
* SX128x: Add preamble IRQ and false detection handling to active receiving check
* Remove unnecessary function declaration
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
