Commit Graph

320 Commits

Author SHA1 Message Date
Thomas Göttgens
430908f5d6 TLORA_T3_S3 2022-12-28 13:56:56 +01:00
Thomas Göttgens
f3c5a01daf remove a few DSR Router bits for S&F Module 2022-11-28 21:58:30 +01:00
Thomas Göttgens
c7681cb24d update board definition, update copy/paste errors, fix SX1280. 2022-11-27 14:03:50 +01:00
Ihor Nehrutsa
6507683909 Squashed commit of the following:
commit c8d1bcf04fae5f7ac5b639ddd15a738045014c95
Author: Ihor Nehrutsa <Ihor.Nehrutsa@gmail.com>
Date:   Fri Nov 25 15:11:18 2022 +0200

    Revert "variants\tbeam\variant.h: Use LORA_CS instead of RF95_NSS"

    This reverts commit 8d225ced9c.

commit 1c37097448393ea9364c2b9bf10522802c61d5c4
Author: Ihor Nehrutsa <Ihor.Nehrutsa@gmail.com>
Date:   Fri Nov 25 15:04:09 2022 +0200

    Some little debugs added

commit f1b55e11af
Author: Ihor Nehrutsa <Ihor.Nehrutsa@gmail.com>
Date:   Wed Nov 23 15:24:58 2022 +0200

    Update variant.h

commit 8d225ced9c
Author: Ihor Nehrutsa <Ihor.Nehrutsa@gmail.com>
Date:   Wed Nov 23 13:06:49 2022 +0200

    variants\tbeam\variant.h: Use LORA_CS instead of RF95_NSS
2022-11-25 15:17:24 +02:00
Thomas Göttgens
401b92bdbb reverted too much 2022-11-13 15:28:43 +01:00
Thomas Göttgens
6a696af8f6 Revert "remember which devices were scanned on which bus and set them accordingly." - this is not working at all. 2022-11-13 14:56:52 +01:00
Thomas Göttgens
037d6c253b fix portduino 2022-11-13 11:58:02 +01:00
Thomas Göttgens
861ded37db remember which devices were scanned on which bus and set them accordingly. 2022-11-12 17:12:40 +01:00
Thomas Göttgens
7a67388a97 Merge branch 'master' of github.com:meshtastic/firmware into develop 2022-11-12 14:34:51 +01:00
lewis
60fdf9fcb2 Place PMU initialization before scanI2Cdevice 2022-11-12 20:09:25 +08:00
Thomas Göttgens
65197a8e48 - Add new Compass Sensor
- speed up I2C Scanning
- make adding sensors less error prone
2022-11-12 11:03:29 +01:00
lewishe
43f769ebac Resolve compilation conflicts 2022-11-12 16:01:30 +08:00
lewishe
dff6eeb90e Merge branch 'master' of https://github.com/lewisxhe/Meshtastic-device 2022-11-12 15:16:54 +08:00
lewishe
61ebdb3367 Add SD card initialization 2022-11-12 15:14:13 +08:00
lewishe
cd95d0865f Repair the sharing of Wire1 between RTC and PMU in tbeams3 2022-11-12 15:12:53 +08:00
lewis he
888a8d05c4
Merge branch 'meshtastic:master' into master 2022-11-12 09:56:18 +08:00
Thomas Göttgens
74f31d7d68 Fix SX1280 init 2022-11-10 23:00:01 +01:00
Thomas Göttgens
09cdc20440 manual merge of changes from Master 2022-11-04 19:56:44 +01:00
Thomas Göttgens
4ccb4393c5 Fix MQTT on ETH 2022-11-04 19:44:45 +01:00
Thomas Göttgens
acfa186d44 Override Screen Autodtect 2022-11-03 22:44:22 +01:00
Thomas Göttgens
3e82cd7dd4 Support for TLORA 2.1-1.8 2022-11-02 18:19:09 +01:00
Thomas Göttgens
12df55c3d4 Support for TLORA 2.1-1.8 2022-11-02 13:12:15 +01:00
Thomas Göttgens
d7c98062ce Merge remote-tracking branch 'remotes/origin/master' into remove-softap 2022-10-26 17:54:21 +02:00
Thomas Göttgens
b7ebe03ca8 API Server and DHCP Lease Management 2022-10-26 11:09:59 +02:00
Thomas Göttgens
a66538fe55 MQTT is working over ethernet 2022-10-26 00:07:02 +02:00
Thomas Göttgens
338c9c1e0c Remove Captive Portal and SoftAP Mode 2022-10-25 11:53:22 +02:00
Thomas Göttgens
aab52f1e8d Merge branch 'master' of github.com:meshtastic/Meshtastic-device 2022-10-23 16:41:04 +02:00
Mykhailo Lesyk
41267a42f7
[rak4630] enable 3.3v periphery before scan for i2c devices (#1847)
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
2022-10-22 19:55:34 -05:00
Thomas Göttgens
1e97dcbb4c Portduino is always special. 2022-10-22 16:53:57 +02:00
Thomas Göttgens
f3fee5f4fb first murmurs of ethernet support 2022-10-22 16:29:50 +02:00
lewis he
da2279c295
Merge branch 'meshtastic:master' into master 2022-10-22 18:22:12 +08:00
Thomas Göttgens
5f4b93aba2 portduino cannot use this chip yet as it uses an old modified version of radiolib 2022-10-17 10:31:29 +02:00
Thomas Göttgens
31c2c8a7a3 only allow wide BW settings when the right chip is detected 2022-10-17 10:00:00 +02:00
Thomas Göttgens
f6119639bb Add support for SX1281 on 2.4 GHz 2022-10-16 19:07:58 +02:00
Thomas Göttgens
a7e0127793 scan i2c twice for all devices, not just tbeam 2022-10-13 23:46:25 +02:00
Thomas Göttgens
b5fb0f60b0 don't compile on Portduino 2022-10-13 13:01:24 +02:00
Thomas Göttgens
a7fe69ed6b Support for ATECCA608B Cryptographic Coprocessor 2022-10-13 12:55:28 +02:00
lewishe
13e635b74e Add judgment on t-beam-s3-core to scanI2Cdevice in main.cpp 2022-10-10 11:50:18 +08:00
Thomas Göttgens
b2d753ed86
move and repeat i2c scan to fix BLE PIN 2022-10-08 17:36:39 +02:00
Ben Meadors
bf4115a80f
Telemetry sensors re-map (#1765)
* Add factory erase uf2 to the release assets

* Sensors map

* Uncomment sensors
2022-10-07 08:33:07 -05:00
lewis he
004f6fa4d6
Add t-beam-s3-core onboard device support. (#1764)
* Change t-beam-s3-core pins definitions

* Add t-beam-s3-core power initialization to properly initialize the I2C device

* Add 6-axis and 3-axis sensor detection
2022-10-07 06:57:55 -05:00
Thomas Göttgens
f7331a2e41 fix #1713
stop output to serial debug after config has been loaded (if serial is disabled), and only accept protobuf packets from that point on.
2022-10-05 10:33:39 +02:00
Thomas Göttgens
3597685b23 Only save the changed parts of config to disk. 2022-10-04 14:32:07 +02:00
GUVWAF
b53dcb932e Adapt conditional include 2022-10-01 17:01:25 +02:00
GUVWAF
68282682de Use new SimRadio in main for Portduino 2022-10-01 12:03:35 +02:00
GUVWAF
2696b04138 Allow Portduino to set the TCP port 2022-10-01 12:02:29 +02:00
Thomas Göttgens
ab342ce904 Freetext Input with CardKB Take 1 - Also removes FacesKB support, this thing is ancient. 2022-09-20 13:50:18 +02:00
Sacha Weatherstone
60b4dbfdcd
More default inits. (#1689)
* More default inits.

* update protobufs

* Try checking has_device first

Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
2022-09-11 08:36:47 -05:00
Ben Meadors
f98e96cf1b Slots for upcoming telemetry sensor support 2022-09-10 17:28:01 -05:00
Thomas Göttgens
7f293bfda3
Merge branch 'master' into master 2022-09-09 21:39:29 +02:00