* Make button timing configurable per variant
* Adjust button timing for T-Echo
Easier multi-clicks for features like "toggle backlight" (4x click)
* Fewer full-refreshes for T-Echo display
Disables ghost pixel tracking: T-Echo ghost pixels are fairly faint.
* Updated kbI2cBase.cpp
Updated keyboard settings for t-deck to allow a modifier key to trigger 'tab', mute notifications, or quit. To trigger the modifier press the shift key and mic (0) button at the same time. Then press q (quit), m (mute), or t (tab).
* Update kbI2cBase.cpp
* fixed formatting issues in kbI2cBase.cpp
* Removed keyboard shortcut code that doesnt work
alt+t does not work on a t-deck so I removed it to avoid confusion.
* Updated kbI2cBase.cpp
Updated keyboard settings for t-deck to allow a modifier key to trigger 'tab', mute notifications, or quit. To trigger the modifier press the shift key and mic (0) button at the same time. Then press q (quit), m (mute), or t (tab).
* Update kbI2cBase.cpp
* fixed formatting issues in kbI2cBase.cpp
* Removed keyboard shortcut code that doesnt work
alt+t does not work on a t-deck so I removed it to avoid confusion.
* Changed modifier key to alt+c
* Added screen brightness functionality
Use modifier key with o(+) to increase brightness or i(-) to decrease.
Currently there are 4 levels of brightness, (L, ML, MH, H). I would like to add a popup message to tell you the brightness.
* Added checks to disable screen brightness changes on unsupported hardware
* Setting the brightness code to work on only applicable devices
* Added "function symbol" display to bottom right corner of screen. Now shows when mute is active or modifier key is pressed. Also fixed some other minor issues.
* commented out a log
* Reworked how modifier functions worked, added
I wasn’t happy with my previous implementation, and I think it would have caused issues with other devices. This should work on all devices.
* Added back the function I moved causing issue with versions
* Fixed the version conflicts, everything seems to work fine now
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
* I2C is not defined in the reference schematic nor HT-DEV-ESP board, remove definition accordingly
* There is no screen in the the reference schematic nor HT-DEV-ESP board, change definition accordingly
* BUTTON_PIN has a 10 kOhm pullup resistor on HT-DEV-ESP, turning off redundant internal pullup should save some power
* LED is connected to GPIO2 on HT-DEV-ESP and is not inverted, update definition accordingly
* Remove redundant undef lines for LoRa pins
Above changes were built and flashed to my [HT-DEV-ESP_V2 board purchased from Heltec's Taobao store](https://item.taobao.com/item.htm?id=521590063077).
Signed-off-by: Andrew Yong <me@ndoo.sg>
Define BATTERY_SENSE_RESOLUTION_BITS based on [amoroz's snippet on the Meshtastic forum](https://meshtastic.discourse.group/t/new-1w-diy-variant-xiao-nrf52840-ebyte-e22-900m30s/7904/10).
Fixes following build error:
```
src/Power.cpp: In member function 'virtual uint16_t AnalogBatteryLevel::getBattVoltage()':
src/Power.cpp:224:79: error: 'BATTERY_SENSE_RESOLUTION_BITS' was not declared in this scope
scaled = operativeAdcMultiplier * ((1000 * AREF_VOLTAGE) / pow(2, BATTERY_SENSE_RESOLUTION_BITS)) * raw;
```
Signed-off-by: Andrew Yong <me@ndoo.sg>
* add new variant: TWC_mesh_v4
* fix trunk format
* fix format under wsl
* change board to TWC_mesh_v4
* change platformio & variant.h properly
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
