; The very slick RAK wireless RAK 4631 / 4630 board - Unified firmware for 5005/19003, with or without OLED RAK 1921
[env:rak4631_eth_gw]
extends = nrf52840_base
board = wiscore_rak4631
board_check = true
build_flags = ${nrf52840_base.build_flags} -Ivariants/rak4631_eth_gw -D RAK_4631
  -L "${platformio.libdeps_dir}/${this.__env__}/bsec2/src/cortex-m4/fpv4-sp-d16-hard"
  -DGPS_POWER_TOGGLE ; comment this line to disable triple press function on the user button to turn off gps entirely.
  -DEINK_DISPLAY_MODEL=GxEPD2_213_BN
  -DEINK_WIDTH=250
  -DEINK_HEIGHT=122
  -DNRF52_USE_JSON=1
  -DMESHTASTIC_EXCLUDE_GPS=1
  -DMESHTASTIC_EXCLUDE_WIFI=1
  -DMESHTASTIC_EXCLUDE_SCREEN=1
;   -DMESHTASTIC_EXCLUDE_PKI=1
  -DMESHTASTIC_EXCLUDE_POWER_FSM=1
  -DMESHTASTIC_EXCLUDE_POWERMON=1
;   -DMESHTASTIC_EXCLUDE_TZ=1
  -DMESHTASTIC_EXCLUDE_EXTERNALNOTIFICATION=1
  -DMESHTASTIC_EXCLUDE_PAXCOUNTER=1
  -DMESHTASTIC_EXCLUDE_REMOTEHARDWARE=1
  -DMESHTASTIC_EXCLUDE_STOREFORWARD=1
  -DMESHTASTIC_EXCLUDE_CANNEDMESSAGES=1
  -DMESHTASTIC_EXCLUDE_WAYPOINT=1
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/rak4631_eth_gw> +<mesh/eth/> +<mesh/api/> +<mqtt/>
lib_deps = 
  ${nrf52840_base.lib_deps}
  ${networking_base.lib_deps}
  melopero/Melopero RV3028@^1.1.0
  https://github.com/RAKWireless/RAK13800-W5100S.git#1.0.2
  rakwireless/RAKwireless NCP5623 RGB LED library@^1.0.2
  https://github.com/meshtastic/RAK12034-BMX160.git#4821355fb10390ba8557dc43ca29a023bcfbb9d9
  bblanchon/ArduinoJson @ 6.21.4
; If not set we will default to uploading over serial (first it forces bootloader entry by talking 1200bps to cdcacm)
; Note: as of 6/2013 the serial/bootloader based programming takes approximately 30 seconds
;upload_protocol = jlink

; Allows programming and debug via the RAK NanoDAP as the default debugger tool for the RAK4631 (it is only $10!)
; programming time is about the same as the bootloader version.
; For information on this see the meshtastic developers documentation for "Development on the NRF52"
[env:rak4631_eth_gw_dbg]
extends = env:rak4631
board_level = extra

; if the builtin version of openocd has a buggy version of semihosting, so use the external version
; platform_packages = platformio/tool-openocd@^3.1200.0

build_flags =
  ${env:rak4631_eth_gw.build_flags}
  -D USE_SEMIHOSTING

lib_deps =
  ${env:rak4631_eth_gw.lib_deps}
  https://github.com/geeksville/Armduino-Semihosting.git#35b538fdf208c3530c1434cd099a08e486672ee4

; NOTE: the pyocd support for semihosting is buggy.  So I switched to using the builtin platformio support for the stlink adapter which worked much better.
; However the built in openocd version in platformio has buggy support for TCP to semihosting. 
;
; So I'm now trying the external openocd - but the openocd scripts for nrf52.cfg assume you are using a DAP adapter not an STLINK adapter.
; In theory I could change those scripts.  But for now I'm trying going back to a DAP adapter but with the external openocd.

upload_protocol = stlink
; eventually use platformio/tool-pyocd@^2.3600.0 instad
;upload_protocol = custom
;upload_command = pyocd flash -t nrf52840 $UPLOADERFLAGS $SOURCE