; Meshtastic DIY v1 by Nano VHF Schematic based on ESP32-WROOM-32 (38 pins) devkit & EBYTE E22 SX1262/SX1268 module
[env:meshtastic-diy-v1]
extends = esp32_base
board = esp32doit-devkit-v1
board_check = true
build_flags =
  ${esp32_base.build_flags}
  -D DIY_V1
  -D EBYTE_E22
  -I variants/diy/v1

; Meshtastic DIY v1.1 new schematic based on ESP32-WROOM-32 & SX1262/SX1268 modules
[env:meshtastic-diy-v1_1]
extends = esp32_base
board = esp32doit-devkit-v1
board_level = extra
build_flags =
  ${esp32_base.build_flags}
  -D DIY_V1
  -D EBYTE_E22
  -I variants/diy/v1_1

; Port to Disaster Radio's ESP32-v3 Dev Board
[env:meshtastic-dr-dev]
extends = esp32_base
board = esp32doit-devkit-v1
board_upload.maximum_size = 4194304
board_upload.maximum_ram_size = 532480
build_flags =
  ${esp32_base.build_flags}
  -D DR_DEV
  -D EBYTE_E22
  -I variants/diy/dr-dev

; Hydra - Meshtastic DIY v1 hardware with some specific changes
[env:hydra]
extends = esp32_base
board = esp32doit-devkit-v1
build_flags =
  ${esp32_base.build_flags}
  -D DIY_V1
  -I variants/diy/hydra


; Promicro + E22(0)-xxxMM / RA-01SH modules board variant - DIY - without TCXO
[env:nrf52_promicro_diy_xtal]
extends = nrf52840_base
board = promicro-nrf52840
board_level = extra
build_flags = ${nrf52840_base.build_flags}
  -I variants/diy/nrf52_promicro_diy_xtal
  -D NRF52_PROMICRO_DIY
  -L "${platformio.libdeps_dir}/${this.__env__}/bsec2/src/cortex-m4/fpv4-sp-d16-hard"
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/diy/nrf52_promicro_diy_xtal>
lib_deps = 
  ${nrf52840_base.lib_deps}
debug_tool = jlink


; Promicro + E22(0)-xxxM / HT-RA62 modules board variant - DIY - with TCXO
[env:nrf52_promicro_diy_tcxo]
extends = nrf52840_base
board = promicro-nrf52840
build_flags = ${nrf52840_base.build_flags}
  -I variants/diy/nrf52_promicro_diy_tcxo
  -D NRF52_PROMICRO_DIY
  -L "${platformio.libdeps_dir}/${this.__env__}/bsec2/src/cortex-m4/fpv4-sp-d16-hard"
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/diy/nrf52_promicro_diy_tcxo>
lib_deps = 
  ${nrf52840_base.lib_deps}
debug_tool = jlink

; NanoVHF T-Energy-S3 + E22(0)-xxxM - DIY
[env:t-energy-s3_e22]
extends = esp32s3_base
board = esp32-s3-devkitc-1
board_level = extra
board_upload.flash_size = 16MB ;Specify the FLASH capacity as 16MB
board_build.arduino.memory_type = qio_opi ;Enable internal PSRAM
build_unflags =
  ${esp32s3_base.build_unflags}
  -D ARDUINO_USB_MODE=1
build_flags =
  ${esp32s3_base.build_flags}
  -D EBYTE_ESP32_S3
  -D BOARD_HAS_PSRAM
  -D ARDUINO_USB_MODE=0
  -D ARDUINO_USB_CDC_ON_BOOT=1
  -I variants/diy/t-energy-s3_e22