firmware/src/mesh/RadioLibInterface.h

#pragma once

#include "MeshPacketQueue.h"
#include "RadioInterface.h"
#include "concurrency/NotifiedWorkerThread.h"

#include <RadioLib.h>

// ESP32 has special rules about ISR code
#ifdef ARDUINO_ARCH_ESP32
#define INTERRUPT_ATTR IRAM_ATTR
#else
#define INTERRUPT_ATTR
#endif

#define RADIOLIB_PIN_TYPE uint32_t

/**
 * We need to override the RadioLib ArduinoHal class to add mutex protection for SPI bus access
 */
class LockingArduinoHal : public ArduinoHal
{
  public:
    LockingArduinoHal(SPIClass &spi, SPISettings spiSettings, RADIOLIB_PIN_TYPE _busy = RADIOLIB_NC)
        : ArduinoHal(spi, spiSettings)
    {
#if ARCH_PORTDUINO
        busy = _busy;
#endif
    };

    void spiBeginTransaction() override;
    void spiEndTransaction() override;
#if ARCH_PORTDUINO
    RADIOLIB_PIN_TYPE busy;
    void spiTransfer(uint8_t *out, size_t len, uint8_t *in) override;

#endif
};

#if defined(USE_STM32WLx)
/**
 * A wrapper for the RadioLib STM32WLx_Module class, that doesn't connect any pins as they are virtual
 */
class STM32WLx_ModuleWrapper : public STM32WLx_Module
{
  public:
    STM32WLx_ModuleWrapper(LockingArduinoHal *hal, RADIOLIB_PIN_TYPE cs, RADIOLIB_PIN_TYPE irq, RADIOLIB_PIN_TYPE rst,
                           RADIOLIB_PIN_TYPE busy)
        : STM32WLx_Module(){};
};
#endif

class RadioLibInterface : public RadioInterface, protected concurrency::NotifiedWorkerThread
{
    /// Used as our notification from the ISR
    enum PendingISR { ISR_NONE = 0, ISR_RX, ISR_TX, TRANSMIT_DELAY_COMPLETED };

    /**
     * Raw ISR handler that just calls our polymorphic method
     */
    static void isrTxLevel0(), isrLevel0Common(PendingISR code);

    /**
     * Debugging counts
     */
    uint32_t rxBad = 0, rxGood = 0, txGood = 0;

    MeshPacketQueue txQueue = MeshPacketQueue(MAX_TX_QUEUE);

  protected:
    /**
     * We use a meshtastic sync word, but hashed with the Channel name.  For releases before 1.2 we used 0x12 (or for very old
     * loads 0x14) Note: do not use 0x34 - that is reserved for lorawan
     *
     * We now use 0x2b (so that someday we can possibly use NOT 2b - because that would be funny pun).  We will be staying with
     * this code for a long time.
     */
    const uint8_t syncWord = 0x2b;

    float currentLimit = 100; // 100mA OCP - Should be acceptable for RFM95/SX127x chipset.

#if !defined(USE_STM32WLx)
    Module module; // The HW interface to the radio
#else
    STM32WLx_ModuleWrapper module;
#endif

    /**
     * provides lowest common denominator RadioLib API
     */
    PhysicalLayer *iface;

    /// are _trying_ to receive a packet currently (note - we might just be waiting for one)
    bool isReceiving = false;

  public:
    /** Our ISR code currently needs this to find our active instance
     */
    static RadioLibInterface *instance;

    /**
     * Glue functions called from ISR land
     */
    virtual void disableInterrupt() = 0;

    /**
     * Enable a particular ISR callback glue function
     */
    virtual void enableInterrupt(void (*)()) = 0;

  public:
    RadioLibInterface(LockingArduinoHal *hal, RADIOLIB_PIN_TYPE cs, RADIOLIB_PIN_TYPE irq, RADIOLIB_PIN_TYPE rst,
                      RADIOLIB_PIN_TYPE busy, PhysicalLayer *iface = NULL);

    virtual ErrorCode send(meshtastic_MeshPacket *p) override;

    /**
     * Return true if we think the board can go to sleep (i.e. our tx queue is empty, we are not sending or receiving)
     *
     * This method must be used before putting the CPU into deep or light sleep.
     */
    virtual bool canSleep() override;

    /**
     * Start waiting to receive a message
     *
     * External functions can call this method to wake the device from sleep.
     * Subclasses must override and call this base method
     */
    virtual void startReceive();

    /** can we detect a LoRa preamble on the current channel? */
    virtual bool isChannelActive() = 0;

    /** are we actively receiving a packet (only called during receiving state)
     *  This method is only public to facilitate debugging.  Do not call.
     */
    virtual bool isActivelyReceiving() = 0;

    /** Attempt to cancel a previously sent packet.  Returns true if a packet was found we could cancel */
    virtual bool cancelSending(NodeNum from, PacketId id) override;

  private:
    /** if we have something waiting to send, start a short (random) timer so we can come check for collision before actually
     * doing the transmit */
    void setTransmitDelay();

    /** random timer with certain min. and max. settings */
    void startTransmitTimer(bool withDelay = true);

    /** timer scaled to SNR of to be flooded packet */
    void startTransmitTimerSNR(float snr);

    void handleTransmitInterrupt();
    void handleReceiveInterrupt();

    static void timerCallback(void *p1, uint32_t p2);

    virtual void onNotify(uint32_t notification) override;

    /** start an immediate transmit
     *  This method is virtual so subclasses can hook as needed, subclasses should not call directly
     */
    virtual void startSend(meshtastic_MeshPacket *txp);

    meshtastic_QueueStatus getQueueStatus();

  protected:
    /** Do any hardware setup needed on entry into send configuration for the radio.
     * Subclasses can customize, but must also call this base method */
    virtual void configHardwareForSend();

    /** Could we send right now (i.e. either not actively receiving or transmitting)? */
    virtual bool canSendImmediately();

    /**
     * Raw ISR handler that just calls our polymorphic method
     */
    static void isrRxLevel0();

    /**
     * If a send was in progress finish it and return the buffer to the pool */
    void completeSending();

    /**
     * Add SNR data to received messages
     */
    virtual void addReceiveMetadata(meshtastic_MeshPacket *mp) = 0;

    /**
     * Subclasses must override, implement and then call into this base class implementation
     */
    virtual void setStandby();
};