mirror of
https://github.com/meshtastic/firmware.git
synced 2025-02-08 05:31:25 +00:00
1a2c7f00e1
* Refactor GPS to not probe if pins not defined * Use Named Constructor to clean up code * Move doGPSPowerSave to GPS class * Make sure to set GPS awake on triple-click * Cleanup and remove dead code * Rename GPS_PIN_WAKE to GPS_PIN_STANDBY * Actually put GPS to sleep between fixes * add GPS_POWER_TOGGLE for heltec-tracker and t-deck * Change GPS_THREAD_INTERVAL to 200 ms * More dead code, compiler warnings, and add returns * Add Number of sats to log output * Add pgs enable and triple-click config * Track average GPS fix time to judge low-power time * Feed PositionModule on GPS fix * Don't turn off the 3v3_s line on RAK4631 when the rotary is present. * Add GPS power standbyOnly option * Delay setting time currentQuality to avoid strange log message. * Typos, comments, and remove unused variable * Short-circuit the setAwake logic on GPS disable * heltec-tracker 0.3 GPS power saving * set en_gpio to defined state * Fix fixed_position logic with GPS disabled * Don't process GPS serial when not isAwake * Add quirk for Heltec Tracker GPS powersave --------- Co-authored-by: Ben Meadors <benmmeadors@gmail.com> Co-authored-by: mverch67 <manuel.verch@gmx.de> Co-authored-by: Manuel <71137295+mverch67@users.noreply.github.com>
62 lines
1.9 KiB
C
62 lines
1.9 KiB
C
#define LED_PIN 18
|
|
|
|
// ST7735S TFT LCD
|
|
#define ST7735S 1 // there are different (sub-)versions of ST7735
|
|
#define ST7735_CS 38
|
|
#define ST7735_RS 40 // DC
|
|
#define ST7735_SDA 42 // MOSI
|
|
#define ST7735_SCK 41
|
|
#define ST7735_RESET 39
|
|
#define ST7735_MISO -1
|
|
#define ST7735_BUSY -1
|
|
#define ST7735_BL 45
|
|
#define ST7735_SPI_HOST SPI3_HOST
|
|
#define ST7735_BACKLIGHT_EN 45
|
|
#define SPI_FREQUENCY 40000000
|
|
#define SPI_READ_FREQUENCY 16000000
|
|
#define SCREEN_ROTATE
|
|
#define TFT_HEIGHT 160
|
|
#define TFT_WIDTH 80
|
|
#define TFT_OFFSET_X 26
|
|
#define TFT_OFFSET_Y 0
|
|
#define VTFT_CTRL 46 // Heltec Tracker needs this pulled low for TFT
|
|
#define SCREEN_TRANSITION_FRAMERATE 1 // fps
|
|
#define DISPLAY_FORCE_SMALL_FONTS
|
|
|
|
#define VEXT_ENABLE Vext // active low, powers the oled display and the lora antenna boost
|
|
#define BUTTON_PIN 0
|
|
|
|
#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
|
|
#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
|
|
#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider
|
|
#define ADC_MULTIPLIER 4.9
|
|
|
|
#undef GPS_RX_PIN
|
|
#undef GPS_TX_PIN
|
|
#define GPS_RX_PIN 33
|
|
#define GPS_TX_PIN 34
|
|
#define PIN_GPS_RESET 35
|
|
#define PIN_GPS_PPS 36
|
|
#define VGNSS_CTRL 37 // Heltec Tracker needs this pulled low for GPS
|
|
#define PIN_GPS_EN VGNSS_CTRL
|
|
#define GPS_EN_ACTIVE LOW
|
|
#define GPS_RESET_MODE LOW
|
|
#define GPS_UC6580
|
|
|
|
#define USE_SX1262
|
|
#define LORA_DIO0 -1 // a No connect on the SX1262 module
|
|
#define LORA_RESET 12
|
|
#define LORA_DIO1 14 // SX1262 IRQ
|
|
#define LORA_DIO2 13 // SX1262 BUSY
|
|
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
|
|
|
|
#define RF95_SCK 9
|
|
#define RF95_MISO 11
|
|
#define RF95_MOSI 10
|
|
#define RF95_NSS 8
|
|
|
|
#define SX126X_CS RF95_NSS
|
|
#define SX126X_DIO1 LORA_DIO1
|
|
#define SX126X_BUSY LORA_DIO2
|
|
#define SX126X_RESET LORA_RESET
|
|
#define SX126X_E22 |