mirror of
https://github.com/meshtastic/firmware.git
synced 2025-06-08 14:12:05 +00:00
cc66f7c79b
* SD software SPI control * fix notification crash; * allow wake on touch * don't build non-MUI variants * use pwm buzzer * Finalize support for Crowpanel TFT 2.4, 2.8 and 3.5 * add hardware ID for TFT panels * Add stubs for the bigger panels. WIP! * fix braces * elecrow 4.3, 5.0, 7.0 support * completed implementation 4.3, 5.0, 7.0 variants * NodeDB default config & simplified light sleep macros * trunk fmt * remove flags * removed leftovers (note: rtc gpios are only needed for deep sleep; the remove section caused issues with the elecrows) --------- Co-authored-by: mverch67 <manuel.verch@gmx.de> Co-authored-by: Manuel <71137295+mverch67@users.noreply.github.com> Co-authored-by: Austin <vidplace7@gmail.com>
91 lines
2.1 KiB
C
91 lines
2.1 KiB
C
#define I2C_SDA 15
|
|
#define I2C_SCL 16
|
|
|
|
#if CROW_SELECT == 1
|
|
#define WAKE_ON_TOUCH
|
|
#define SCREEN_TOUCH_INT 47
|
|
#define USE_POWERSAVE
|
|
#define SLEEP_TIME 180
|
|
#endif
|
|
|
|
#if CROW_SELECT == 1
|
|
// dac / amp
|
|
// #define HAS_I2S // didn't get I2S sound working
|
|
#define PIN_BUZZER 8 // using pwm buzzer instead (nobody will notice, lol)
|
|
#define DAC_I2S_BCK 13
|
|
#define DAC_I2S_WS 11
|
|
#define DAC_I2S_DOUT 12
|
|
#define DAC_I2S_MCLK 8 // don't use GPIO0 because it's assigned to LoRa or button
|
|
#else
|
|
#define PIN_BUZZER 8
|
|
#endif
|
|
|
|
// GPS via UART1 connector
|
|
#define GPS_DEFAULT_NOT_PRESENT 1
|
|
#define HAS_GPS 1
|
|
#if CROW_SELECT == 1
|
|
#define GPS_RX_PIN 18
|
|
#define GPS_TX_PIN 17
|
|
#else
|
|
// GPIOs shared with LoRa or MIC module
|
|
#define GPS_RX_PIN 19
|
|
#define GPS_TX_PIN 20
|
|
#endif
|
|
|
|
// Extension Slot Layout, viewed from above (2.4-3.5)
|
|
// DIO1/IO1 o o IO2/NRESET
|
|
// SCK/IO10 o o IO16/NC
|
|
// MISO/IO9 o o IO15/NC
|
|
// MOSI/IO3 o o NC/DIO2
|
|
// 3V3 o o IO46/BUSY
|
|
// GND o o IO0/NSS
|
|
// 5V/NC o o NC/DIO3
|
|
// J9 J8
|
|
|
|
// Extension Slot Layout, viewed from above (4.3-7.0)
|
|
// !! DIO1/IO20 o o IO19/NRESET !!
|
|
// !! SCK/IO5 o o IO16/NC
|
|
// !! MISO/IO4 o o IO15/NC
|
|
// !! MOSI/IO6 o o NC/DIO2
|
|
// 3V3 o o IO2/BUSY !!
|
|
// GND o o IO0/NSS
|
|
// 5V/NC o o NC/DIO3
|
|
// J9 J8
|
|
|
|
// LoRa
|
|
#define USE_SX1262
|
|
|
|
#if CROW_SELECT == 1
|
|
// 2.4", 2.8, 3.5"""
|
|
#define HW_SPI1_DEVICE
|
|
#define LORA_CS 0
|
|
#define LORA_SCK 10
|
|
#define LORA_MISO 9
|
|
#define LORA_MOSI 3
|
|
|
|
#define LORA_RESET 2
|
|
#define LORA_DIO1 1 // SX1262 IRQ
|
|
#define LORA_DIO2 46 // SX1262 BUSY
|
|
|
|
// need to pull IO45 low to enable LORA and disable Microphone on 24 28 35
|
|
#define SENSOR_POWER_CTRL_PIN 45
|
|
#define SENSOR_POWER_ON LOW
|
|
#else
|
|
// 4.3", 5.0", 7.0"
|
|
#define LORA_CS 0
|
|
#define LORA_SCK 5
|
|
#define LORA_MISO 4
|
|
#define LORA_MOSI 6
|
|
|
|
#define LORA_RESET 19
|
|
#define LORA_DIO1 20 // SX1262 IRQ
|
|
#define LORA_DIO2 2 // SX1262 BUSY
|
|
#endif
|
|
|
|
#define SX126X_CS LORA_CS
|
|
#define SX126X_DIO1 LORA_DIO1
|
|
#define SX126X_BUSY LORA_DIO2
|
|
#define SX126X_RESET LORA_RESET
|
|
#define SX126X_DIO2_AS_RF_SWITCH
|
|
#define SX126X_DIO3_TCXO_VOLTAGE 3.3
|