firmware/variants/esp32s3/tracksenger/internal/variant.h

#define LED_PIN 18

#define HELTEC_TRACKER_V1_X

// TRACKSENGER builtin LCD

// I2C
#define I2C_SDA SDA
#define I2C_SCL SCL

// ST7735S TFT LCD
#define ST7735S 1 // there are different (sub-)versions of ST7735
#define ST7735_CS 38
#define ST7735_RS 40  // DC
#define ST7735_SDA 42 // MOSI
#define ST7735_SCK 41
#define ST7735_RESET 39
#define ST7735_MISO -1
#define ST7735_BUSY -1
#define TFT_BL 21 /* V1.1 PCB marking */
#define ST7735_SPI_HOST SPI3_HOST
#define SPI_FREQUENCY 40000000
#define SPI_READ_FREQUENCY 16000000
#define SCREEN_ROTATE
#define TFT_HEIGHT DISPLAY_WIDTH
#define TFT_WIDTH DISPLAY_HEIGHT
#define TFT_OFFSET_X 26
#define TFT_OFFSET_Y -1
#define SCREEN_TRANSITION_FRAMERATE 3 // fps
#define DISPLAY_FORCE_SMALL_FONTS

#define VEXT_ENABLE 3 // active HIGH, powers the lora antenna boost
#define VEXT_ON_VALUE HIGH
#define BUTTON_PIN 0

#define BATTERY_PIN 1 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
#define ADC_CHANNEL ADC1_GPIO1_CHANNEL
#define ADC_ATTENUATION ADC_ATTEN_DB_2_5 // lower dB for high resistance voltage divider
#define ADC_MULTIPLIER 4.9
#define ADC_CTRL 2 // active HIGH, powers the voltage divider. Only on 1.1
#define ADC_CTRL_ENABLED HIGH

#undef GPS_RX_PIN
#undef GPS_TX_PIN
#define GPS_RX_PIN 33
#define GPS_TX_PIN 34
#define PIN_GPS_RESET 35
#define PIN_GPS_PPS 36

#define GPS_RESET_MODE LOW
#define GPS_UC6580
#define GPS_BAUDRATE 115200

#define USE_SX1262
#define LORA_DIO0 -1 // a No connect on the SX1262 module
#define LORA_RESET 12
#define LORA_DIO1 14 // SX1262 IRQ
#define LORA_DIO2 13 // SX1262 BUSY
#define LORA_DIO3    // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled

#define LORA_SCK 9
#define LORA_MISO 11
#define LORA_MOSI 10
#define LORA_CS 8

#define SX126X_CS LORA_CS
#define SX126X_DIO1 LORA_DIO1
#define SX126X_BUSY LORA_DIO2
#define SX126X_RESET LORA_RESET

#define SX126X_DIO2_AS_RF_SWITCH
#define SX126X_DIO3_TCXO_VOLTAGE 1.8

// Picomputer gets a white on black display
#define TFT_MESH_OVERRIDE COLOR565(255, 255, 255)

// keyboard changes

#define PIN_BUZZER 43
#define CANNED_MESSAGE_MODULE_ENABLE 1

#define INPUTBROKER_MATRIX_TYPE 1

#define KEYS_COLS                                                                                                                \
    {                                                                                                                            \
        44, 45, 46, 4, 5, 6                                                                                                      \
    }
#define KEYS_ROWS                                                                                                                \
    {                                                                                                                            \
        26, 37, 17, 16, 15, 7                                                                                                    \
    }
// #end keyboard