mirror of
https://github.com/meshtastic/firmware.git
synced 2025-05-03 04:23:52 +00:00
4b0bbb8af1
* Make STM compile again and update toolchain. The binary is too big for the flash. WIP * Making progress with OSFS, still WIP * more progress, still too big. Adding RAK3172 to the equasion * Make STM compile again and update toolchain. The binary is too big for the flash. WIP * Making progress with OSFS, still WIP * more progress, still too big. Adding RAK3172 to the equasion * still too big * minimize build * trunk fmt * fix a couple of symbol clashes * trunk fmt * down to 101% with a release vs. debug build and omitting the flash strings * fix compilation * fix compilation once more * update protobufs linkage * - Toolchain updated - Fixed macro error * silence compiler warning note: do something about this assert... * new toolkit and fix Power.cpp * STM32WL make it fit (#4330) * Add option to exclude I2C parts The I2C hals and related code uses a significant amount of flash space and aren't required for a basic node. * Add option to disable Admin and NodeInfo modules Disabled by default in minimal build. This saves a significant amount of flash * Disable unused hals These use up significant flash * Add float support for printf for debugging Makes serial look nice for debugging * This breaks my build for some reason * These build flags can save a bit of flash * Don't disable NodeInfo and Admin modules in minimal build They fit in flash * Don't include printf float support by default Only useful for debugging --------- Co-authored-by: Adam Lawson <dev@goshawk22.uk> --------- Co-authored-by: Ben Meadors <benmmeadors@gmail.com> Co-authored-by: Adam Lawson <dev@goshawk22.uk>
31 lines
1.0 KiB
C++
31 lines
1.0 KiB
C++
#pragma once
|
|
|
|
#include "SX126xInterface.h"
|
|
|
|
#ifdef ARCH_STM32WL
|
|
|
|
/**
|
|
* Our adapter for STM32WLE5JC radios
|
|
*/
|
|
class STM32WLE5JCInterface : public SX126xInterface<STM32WLx>
|
|
{
|
|
public:
|
|
STM32WLE5JCInterface(LockingArduinoHal *hal, RADIOLIB_PIN_TYPE cs, RADIOLIB_PIN_TYPE irq, RADIOLIB_PIN_TYPE rst,
|
|
RADIOLIB_PIN_TYPE busy);
|
|
|
|
virtual bool init() override;
|
|
};
|
|
|
|
// https://github.com/Seeed-Studio/LoRaWan-E5-Node/blob/main/Middlewares/Third_Party/SubGHz_Phy/stm32_radio_driver/radio_driver.c
|
|
static const float tcxoVoltage = 1.7;
|
|
|
|
/* https://wiki.seeedstudio.com/LoRa-E5_STM32WLE5JC_Module/
|
|
* Wio-E5 module ONLY transmits through RFO_HP
|
|
* Receive: PA4=1, PA5=0
|
|
* Transmit(high output power, SMPS mode): PA4=0, PA5=1 */
|
|
static const RADIOLIB_PIN_TYPE rfswitch_pins[5] = {PA4, PA5, RADIOLIB_NC, RADIOLIB_NC, RADIOLIB_NC};
|
|
|
|
static const Module::RfSwitchMode_t rfswitch_table[4] = {
|
|
{STM32WLx::MODE_IDLE, {LOW, LOW}}, {STM32WLx::MODE_RX, {HIGH, LOW}}, {STM32WLx::MODE_TX_HP, {LOW, HIGH}}, END_OF_MODE_TABLE};
|
|
|
|
#endif // ARCH_STM32WL
|