mirror of
https://github.com/meshtastic/firmware.git
synced 2025-06-08 14:12:05 +00:00
cc66f7c79b
* SD software SPI control * fix notification crash; * allow wake on touch * don't build non-MUI variants * use pwm buzzer * Finalize support for Crowpanel TFT 2.4, 2.8 and 3.5 * add hardware ID for TFT panels * Add stubs for the bigger panels. WIP! * fix braces * elecrow 4.3, 5.0, 7.0 support * completed implementation 4.3, 5.0, 7.0 variants * NodeDB default config & simplified light sleep macros * trunk fmt * remove flags * removed leftovers (note: rtc gpios are only needed for deep sleep; the remove section caused issues with the elecrows) --------- Co-authored-by: mverch67 <manuel.verch@gmx.de> Co-authored-by: Manuel <71137295+mverch67@users.noreply.github.com> Co-authored-by: Austin <vidplace7@gmail.com>
74 lines
2.1 KiB
C
74 lines
2.1 KiB
C
// meshtastic/firmware/variants/unphone/variant.h
|
|
|
|
#pragma once
|
|
|
|
#define SPI_SCK 39
|
|
#define SPI_MOSI 40
|
|
#define SPI_MISO 41
|
|
|
|
// We use the RFM95W LoRa module
|
|
#define USE_RF95
|
|
#define LORA_SCK SPI_SCK
|
|
#define LORA_MOSI SPI_MOSI
|
|
#define LORA_MISO SPI_MISO
|
|
#define LORA_CS 44
|
|
#define LORA_DIO0 10 // AKA LORA_IRQ
|
|
#define LORA_RESET 42
|
|
#define LORA_DIO1 11
|
|
#define LORA_DIO2 RADIOLIB_NC // Not really used
|
|
|
|
// HX8357 TFT LCD
|
|
#define HX8357_CS 48
|
|
#define HX8357_RS 47 // AKA DC
|
|
#define HX8357_RESET 46
|
|
#define HX8357_SCK SPI_SCK
|
|
#define HX8357_MOSI SPI_MOSI
|
|
#define HX8357_MISO SPI_MISO
|
|
#define HX8357_BUSY -1
|
|
#define HX8357_SPI_HOST SPI2_HOST
|
|
#define SPI_FREQUENCY 40000000
|
|
#define SPI_READ_FREQUENCY 16000000
|
|
#define TFT_HEIGHT 480
|
|
#define TFT_WIDTH 320
|
|
#define TFT_OFFSET_X 0
|
|
#define TFT_OFFSET_Y 0
|
|
#define TFT_OFFSET_ROTATION 6 // unPhone's screen wired unusually, 0 typical
|
|
#define TFT_INVERT false
|
|
#define SCREEN_ROTATE true
|
|
#define SCREEN_TRANSITION_FRAMERATE 5
|
|
|
|
#define HAS_TOUCHSCREEN 1
|
|
#define USE_XPT2046 1
|
|
#define TOUCH_CS 38
|
|
|
|
#define USE_POWERSAVE
|
|
#define SLEEP_TIME 180
|
|
|
|
#define HAS_GPS \
|
|
0 // the unphone doesn't have a gps module by default (though
|
|
// GPS featherwing -- https://www.adafruit.com/product/3133
|
|
// -- can be added)
|
|
#undef GPS_RX_PIN
|
|
#undef GPS_TX_PIN
|
|
|
|
#define SD_SPI_FREQUENCY 25000000
|
|
#define SDCARD_CS 43
|
|
|
|
#define LED_PIN 13 // the red part of the RGB LED
|
|
#define LED_STATE_ON 0 // State when LED is lit
|
|
|
|
#define BUTTON_PIN 21 // Button 3 - square - top button in landscape mode
|
|
#define BUTTON_NEED_PULLUP // we do need a helping hand up
|
|
#define BUTTON_PIN_ALT 45 // Button 1 - triangle - bottom button in landscape mode
|
|
|
|
#define I2C_SDA 3 // I2C pins for this board
|
|
#define I2C_SCL 4
|
|
|
|
#define LSM6DS3_WAKE_THRESH 5 // higher values reduce the sensitivity of the wake threshold
|
|
|
|
// ratio of voltage divider = 3.20 (R1=100k, R2=220k)
|
|
// #define ADC_MULTIPLIER 3.2
|
|
|
|
// #define BATTERY_PIN 13 // battery V measurement pin; vbat divider is here
|
|
// #define ADC_CHANNEL ADC2_GPIO13_CHANNEL
|
|
// #define BAT_MEASURE_ADC_UNIT 2
|