mirror of
https://github.com/meshtastic/firmware.git
synced 2025-10-28 23:34:03 +00:00
273 lines
7.3 KiB
C
273 lines
7.3 KiB
C
/*
|
|
Copyright (c) 2014-2015 Arduino LLC. All right reserved.
|
|
Copyright (c) 2016 Sandeep Mistry All right reserved.
|
|
Copyright (c) 2018, Adafruit Industries (adafruit.com)
|
|
|
|
This library is free software; you can redistribute it and/or
|
|
modify it under the terms of the GNU Lesser General Public
|
|
License as published by the Free Software Foundation; either
|
|
version 2.1 of the License, or (at your option) any later version.
|
|
This library is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
|
See the GNU Lesser General Public License for more details.
|
|
You should have received a copy of the GNU Lesser General Public
|
|
License along with this library; if not, write to the Free Software
|
|
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
|
|
*/
|
|
|
|
#ifndef _VARIANT_RAK4630_
|
|
#define _VARIANT_RAK4630_
|
|
|
|
#define RAK4630
|
|
|
|
/** Master clock frequency */
|
|
#define VARIANT_MCK (64000000ul)
|
|
|
|
#define USE_LFXO // Board uses 32khz crystal for LF
|
|
// define USE_LFRC // Board uses RC for LF
|
|
|
|
/*----------------------------------------------------------------------------
|
|
* Headers
|
|
*----------------------------------------------------------------------------*/
|
|
|
|
#include "WVariant.h"
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif // __cplusplus
|
|
|
|
// Number of pins defined in PinDescription array
|
|
#define PINS_COUNT (48)
|
|
#define NUM_DIGITAL_PINS (48)
|
|
#define NUM_ANALOG_INPUTS (6)
|
|
#define NUM_ANALOG_OUTPUTS (0)
|
|
|
|
// LEDs
|
|
#define PIN_LED1 (35)
|
|
#define PIN_LED2 (36)
|
|
|
|
#define LED_BUILTIN PIN_LED1
|
|
#define LED_CONN PIN_LED2
|
|
|
|
#define LED_GREEN PIN_LED1
|
|
#define LED_BLUE PIN_LED2
|
|
|
|
#define LED_STATE_ON 1 // State when LED is litted
|
|
|
|
/*
|
|
* Buttons
|
|
*/
|
|
|
|
#define PIN_BUTTON1 9 // Pin for button on E-ink button module or IO expansion
|
|
#define BUTTON_NEED_PULLUP
|
|
#define PIN_BUTTON2 12
|
|
#define PIN_BUTTON3 24
|
|
#define PIN_BUTTON4 25
|
|
|
|
/*
|
|
* Analog pins
|
|
*/
|
|
#define PIN_A0 (5)
|
|
#define PIN_A1 (31)
|
|
#define PIN_A2 (28)
|
|
#define PIN_A3 (29)
|
|
#define PIN_A4 (30)
|
|
#define PIN_A5 (31)
|
|
#define PIN_A6 (0xff)
|
|
#define PIN_A7 (0xff)
|
|
|
|
static const uint8_t A0 = PIN_A0;
|
|
static const uint8_t A1 = PIN_A1;
|
|
static const uint8_t A2 = PIN_A2;
|
|
static const uint8_t A3 = PIN_A3;
|
|
static const uint8_t A4 = PIN_A4;
|
|
static const uint8_t A5 = PIN_A5;
|
|
static const uint8_t A6 = PIN_A6;
|
|
static const uint8_t A7 = PIN_A7;
|
|
#define ADC_RESOLUTION 14
|
|
|
|
// Other pins
|
|
#define PIN_AREF (2)
|
|
#define PIN_NFC1 (9)
|
|
#define PIN_NFC2 (10)
|
|
|
|
static const uint8_t AREF = PIN_AREF;
|
|
|
|
/*
|
|
* Serial interfaces
|
|
*/
|
|
#define PIN_SERIAL1_RX (15)
|
|
#define PIN_SERIAL1_TX (16)
|
|
|
|
// Connected to Jlink CDC
|
|
#define PIN_SERIAL2_RX (8)
|
|
#define PIN_SERIAL2_TX (6)
|
|
|
|
/*
|
|
* SPI Interfaces
|
|
*/
|
|
#define SPI_INTERFACES_COUNT 2
|
|
|
|
#define PIN_SPI_MISO (45)
|
|
#define PIN_SPI_MOSI (44)
|
|
#define PIN_SPI_SCK (43)
|
|
|
|
#define PIN_SPI1_MISO (29) // (0 + 29)
|
|
#define PIN_SPI1_MOSI (30) // (0 + 30)
|
|
#define PIN_SPI1_SCK (3) // (0 + 3)
|
|
|
|
static const uint8_t SS = 42;
|
|
static const uint8_t MOSI = PIN_SPI_MOSI;
|
|
static const uint8_t MISO = PIN_SPI_MISO;
|
|
static const uint8_t SCK = PIN_SPI_SCK;
|
|
|
|
/*
|
|
* eink display pins
|
|
*/
|
|
|
|
#define PIN_EINK_CS (0 + 26)
|
|
#define PIN_EINK_BUSY (0 + 4)
|
|
#define PIN_EINK_DC (0 + 17)
|
|
#define PIN_EINK_RES (-1)
|
|
#define PIN_EINK_SCLK (0 + 3)
|
|
#define PIN_EINK_MOSI (0 + 30) // also called SDI
|
|
|
|
// #define USE_EINK
|
|
|
|
// RAKRGB
|
|
#define HAS_NCP5623
|
|
|
|
/*
|
|
* Wire Interfaces
|
|
*/
|
|
#define WIRE_INTERFACES_COUNT 1
|
|
|
|
#define PIN_WIRE_SDA (13)
|
|
#define PIN_WIRE_SCL (14)
|
|
|
|
// QSPI Pins
|
|
#define PIN_QSPI_SCK 3
|
|
#define PIN_QSPI_CS 26
|
|
#define PIN_QSPI_IO0 30
|
|
#define PIN_QSPI_IO1 29
|
|
#define PIN_QSPI_IO2 28
|
|
#define PIN_QSPI_IO3 2
|
|
|
|
// On-board QSPI Flash
|
|
#define EXTERNAL_FLASH_DEVICES IS25LP080D
|
|
#define EXTERNAL_FLASH_USE_QSPI
|
|
|
|
/* @note RAK5005-O GPIO mapping to RAK4631 GPIO ports
|
|
RAK5005-O <-> nRF52840
|
|
IO1 <-> P0.17 (Arduino GPIO number 17)
|
|
IO2 <-> P1.02 (Arduino GPIO number 34)
|
|
IO3 <-> P0.21 (Arduino GPIO number 21)
|
|
IO4 <-> P0.04 (Arduino GPIO number 4)
|
|
IO5 <-> P0.09 (Arduino GPIO number 9)
|
|
IO6 <-> P0.10 (Arduino GPIO number 10)
|
|
IO7 <-> P0.28 (Arduino GPIO number 28)
|
|
SW1 <-> P0.01 (Arduino GPIO number 1)
|
|
A0 <-> P0.04/AIN2 (Arduino Analog A2
|
|
A1 <-> P0.31/AIN7 (Arduino Analog A7
|
|
SPI_CS <-> P0.26 (Arduino GPIO number 26)
|
|
*/
|
|
|
|
// RAK4630 LoRa module
|
|
|
|
/* Setup of the SX1262 LoRa module ( https://docs.rakwireless.com/Product-Categories/WisBlock/RAK4631/Datasheet/ )
|
|
|
|
P1.10 NSS SPI NSS (Arduino GPIO number 42)
|
|
P1.11 SCK SPI CLK (Arduino GPIO number 43)
|
|
P1.12 MOSI SPI MOSI (Arduino GPIO number 44)
|
|
P1.13 MISO SPI MISO (Arduino GPIO number 45)
|
|
P1.14 BUSY BUSY signal (Arduino GPIO number 46)
|
|
P1.15 DIO1 DIO1 event interrupt (Arduino GPIO number 47)
|
|
P1.06 NRESET NRESET manual reset of the SX1262 (Arduino GPIO number 38)
|
|
|
|
Important for successful SX1262 initialization:
|
|
|
|
* Setup DIO2 to control the antenna switch
|
|
* Setup DIO3 to control the TCXO power supply
|
|
* Setup the SX1262 to use it's DCDC regulator and not the LDO
|
|
* RAK4630 schematics show GPIO P1.07 connected to the antenna switch, but it should not be initialized, as DIO2 will do the
|
|
control of the antenna switch
|
|
|
|
SO GPIO 39/TXEN MAY NOT BE DEFINED FOR SUCCESSFUL OPERATION OF THE SX1262 - TG
|
|
|
|
*/
|
|
|
|
#define DETECTION_SENSOR_EN 4
|
|
|
|
#define USE_SX1262
|
|
#define SX126X_CS (42)
|
|
#define SX126X_DIO1 (47)
|
|
#define SX126X_BUSY (46)
|
|
#define SX126X_RESET (38)
|
|
// #define SX126X_TXEN (39)
|
|
// #define SX126X_RXEN (37)
|
|
#define SX126X_POWER_EN (37)
|
|
// DIO2 controlls an antenna switch and the TCXO voltage is controlled by DIO3
|
|
#define SX126X_DIO2_AS_RF_SWITCH
|
|
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
|
|
|
// Testing USB detection
|
|
#define NRF_APM
|
|
|
|
// enables 3.3V periphery like GPS or IO Module
|
|
// Do not toggle this for GPS power savings
|
|
#define PIN_3V3_EN (34)
|
|
|
|
// RAK1910 GPS module
|
|
// If using the wisblock GPS module and pluged into Port A on WisBlock base
|
|
// IO1 is hooked to PPS (pin 12 on header) = gpio 17
|
|
// IO2 is hooked to GPS RESET = gpio 34, but it can not be used to this because IO2 is ALSO used to control 3V3_S power (1 is on).
|
|
// Therefore must be 1 to keep peripherals powered
|
|
// Power is on the controllable 3V3_S rail
|
|
// #define PIN_GPS_RESET (34)
|
|
// #define PIN_GPS_EN PIN_3V3_EN
|
|
#define PIN_GPS_PPS (17) // Pulse per second input from the GPS
|
|
|
|
#define GPS_RX_PIN PIN_SERIAL1_RX
|
|
#define GPS_TX_PIN PIN_SERIAL1_TX
|
|
|
|
// Define pin to enable GPS toggle (set GPIO to LOW) via user button triple press
|
|
|
|
// RAK12002 RTC Module
|
|
#define RV3028_RTC (uint8_t)0b1010010
|
|
|
|
// RAK18001 Buzzer in Slot C
|
|
// #define PIN_BUZZER 21 // IO3 is PWM2
|
|
// NEW: set this via protobuf instead!
|
|
|
|
// Battery
|
|
// The battery sense is hooked to pin A0 (5)
|
|
#define BATTERY_PIN PIN_A0
|
|
// and has 12 bit resolution
|
|
#define BATTERY_SENSE_RESOLUTION_BITS 12
|
|
#define BATTERY_SENSE_RESOLUTION 4096.0
|
|
#undef AREF_VOLTAGE
|
|
#define AREF_VOLTAGE 3.0
|
|
#define VBAT_AR_INTERNAL AR_INTERNAL_3_0
|
|
#define ADC_MULTIPLIER 1.73
|
|
|
|
#define HAS_RTC 1
|
|
|
|
#define HAS_ETHERNET 1
|
|
|
|
#define RAK_4631 1
|
|
|
|
#define PIN_ETHERNET_RESET 21
|
|
#define PIN_ETHERNET_SS PIN_EINK_CS
|
|
#define ETH_SPI_PORT SPI1
|
|
#define AQ_SET_PIN 10
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
/*----------------------------------------------------------------------------
|
|
* Arduino objects - C++ only
|
|
*----------------------------------------------------------------------------*/
|
|
|
|
#endif |