mirror of
https://github.com/meshtastic/firmware.git
synced 2025-02-01 18:29:56 +00:00
502a6596a3
* add hwid for auto-detection * fix: heltec-wireless-tracker USB serial * T-Deck support * trunk fmt * set FRAMERATE to 1 * fix some defines * trunk fmt * corrected vendor link * T-Deck: support keyboard, trackball & touch screen * T-Watch add touchscreen defs, remove getTouch * fix warnings * getTouch uint16 -> int16 * fix touch x,y * fix I2C port * CannedMsgModule: use entire display height * trunk fmt * fix I2C issue for T-Watch * allow dest selection in canned mode * fix: allow dest selection in canned mode * use tft.setBrightness() to poweroff display * Increased t-watch framerate and added back haptic feedback * add da ref * Move to touched * improved sensitivity and accuracy of touch events * use double tap to send canned message * fix warning * trunk fmt * Remove extra hapticFeedback() --------- Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
67 lines
1.8 KiB
C
67 lines
1.8 KiB
C
// ST7789 TFT LCD
|
|
#define ST7789_CS 12
|
|
#define ST7789_RS 38 // DC
|
|
#define ST7789_SDA 13 // MOSI
|
|
#define ST7789_SCK 18
|
|
#define ST7789_RESET -1
|
|
#define ST7789_MISO -1
|
|
#define ST7789_BUSY -1
|
|
#define ST7789_BL 45
|
|
#define ST7789_SPI_HOST SPI3_HOST
|
|
#define ST7789_BACKLIGHT_EN 45
|
|
#define SPI_FREQUENCY 40000000
|
|
#define SPI_READ_FREQUENCY 16000000
|
|
#define TFT_HEIGHT 240
|
|
#define TFT_WIDTH 240
|
|
#define TFT_OFFSET_X 0
|
|
#define TFT_OFFSET_Y 0
|
|
#define SCREEN_ROTATE
|
|
#define SCREEN_TRANSITION_FRAMERATE 5 // fps
|
|
|
|
#define HAS_TOUCHSCREEN 1
|
|
#define SCREEN_TOUCH_INT 16
|
|
#define SCREEN_TOUCH_USE_I2C1
|
|
#define TOUCH_I2C_PORT 1
|
|
#define TOUCH_SLAVE_ADDRESS 0x38
|
|
|
|
#define I2C_SDA1 39 // Used for capacitive touch
|
|
#define I2C_SCL1 40 // Used for capacitive touch
|
|
|
|
#define TFT_BL ST7789_BACKLIGHT_EN
|
|
|
|
#define HAS_AXP2101
|
|
|
|
#define HAS_RTC 1
|
|
|
|
#define I2C_SDA 10 // For QMC6310 sensors and screens
|
|
#define I2C_SCL 11 // For QMC6310 sensors and screens
|
|
|
|
#define BUTTON_PIN 0
|
|
|
|
#define BMA4XX_INT 14 // Interrupt for BMA_423 axis sensor
|
|
|
|
#define HAS_GPS 0
|
|
#undef GPS_RX_PIN
|
|
#undef GPS_TX_PIN
|
|
|
|
#define USE_SX1262
|
|
#define USE_SX1268
|
|
|
|
#define RF95_SCK 3
|
|
#define RF95_MISO 4
|
|
#define RF95_MOSI 1
|
|
#define RF95_NSS 5
|
|
|
|
#define LORA_DIO0 -1 // a No connect on the SX1262 module
|
|
#define LORA_RESET 8
|
|
#define LORA_DIO1 9 // SX1262 IRQ
|
|
#define LORA_DIO2 7 // SX1262 BUSY
|
|
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262, if DIO3 is high the TXCO is enabled
|
|
|
|
#define SX126X_CS RF95_NSS // FIXME - we really should define LORA_CS instead
|
|
#define SX126X_DIO1 LORA_DIO1
|
|
#define SX126X_BUSY LORA_DIO2
|
|
#define SX126X_RESET LORA_RESET
|
|
#define SX126X_E22 // Not really an E22 but TTGO seems to be trying to clone that
|
|
// Internally the TTGO module hooks the SX1262-DIO2 in to control the TX/RX switch (which is the default for
|
|
// the sx1262interface code)
|