mirror of
https://github.com/meshtastic/firmware.git
synced 2025-02-01 18:29:56 +00:00
1a38c4e51d
While working on #4378 I noticed a funny problem: the blinking system LED was on during deep-sleep. Initially I thought it was some weird sleep hw config thing but it turns out it was easier but more pervasive. We had two different preprocessor symbols which both meant approximately the same thing LED_INVERTED and LED_STATE_ON (though their polarity was opposite). Some variant files were setting one, others were setting the other, and others were setting both. heh. In the case of the board I was testing (seeed tracker wio 1100) it was only setting one and the default behavior for the other (for all boards) was incorrect. So I did a grep and it seems like LED_STATE_ON was used more often, so I kept that one and removed LED_INVERTED everywhere.
181 lines
5.1 KiB
C
181 lines
5.1 KiB
C
/*
|
|
Copyright (c) 2014-2015 Arduino LLC. All right reserved.
|
|
Copyright (c) 2016 Sandeep Mistry All right reserved.
|
|
Copyright (c) 2018, Adafruit Industries (adafruit.com)
|
|
|
|
This library is free software; you can redistribute it and/or
|
|
modify it under the terms of the GNU Lesser General Public
|
|
License as published by the Free Software Foundation; either
|
|
version 2.1 of the License, or (at your option) any later version.
|
|
This library is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
|
See the GNU Lesser General Public License for more details.
|
|
You should have received a copy of the GNU Lesser General Public
|
|
License along with this library; if not, write to the Free Software
|
|
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
|
|
*/
|
|
|
|
#ifndef _VARIANT_CANARYONE
|
|
#define _VARIANT_CANARYONE
|
|
|
|
/** Master clock frequency */
|
|
#define VARIANT_MCK (64000000ul)
|
|
|
|
#define USE_LFXO // Board uses 32khz crystal for LF
|
|
|
|
/*----------------------------------------------------------------------------
|
|
* Headers
|
|
*----------------------------------------------------------------------------*/
|
|
|
|
#include "WVariant.h"
|
|
|
|
#ifdef __cplusplus
|
|
extern "C" {
|
|
#endif // __cplusplus
|
|
|
|
#define CANARYONE
|
|
|
|
#define GPIO_PORT0 0
|
|
#define GPIO_PORT1 32
|
|
|
|
// Number of pins defined in PinDescription array
|
|
#define PINS_COUNT (48)
|
|
#define NUM_DIGITAL_PINS (48)
|
|
#define NUM_ANALOG_INPUTS (1)
|
|
#define NUM_ANALOG_OUTPUTS (0)
|
|
|
|
// LEDs
|
|
#define PIN_LED1 (GPIO_PORT1 + 1) // blue P1.01
|
|
#define PIN_LED2 (GPIO_PORT0 + 14) // yellow P0.14
|
|
#define PIN_LED3 (GPIO_PORT1 + 3) // green P1.03
|
|
|
|
#define LED_BLUE PIN_LED1
|
|
|
|
#define LED_BUILTIN PIN_LED1
|
|
#define LED_CONN PIN_LED3
|
|
|
|
#define LED_STATE_ON 0 // State when LED is lit
|
|
|
|
/*
|
|
* Buttons
|
|
*/
|
|
#define PIN_BUTTON1 (GPIO_PORT0 + 15) // BTN0 on schematic
|
|
#define PIN_BUTTON2 (GPIO_PORT0 + 16) // BTN1 on schematic
|
|
|
|
/*
|
|
* Analog pins
|
|
*/
|
|
#define PIN_A0 (4) // Battery ADC P0.04
|
|
|
|
#define BATTERY_PIN PIN_A0
|
|
|
|
static const uint8_t A0 = PIN_A0;
|
|
|
|
#define ADC_RESOLUTION 14
|
|
|
|
/**
|
|
* Wire Interfaces
|
|
*/
|
|
#define WIRE_INTERFACES_COUNT 1
|
|
|
|
#define PIN_WIRE_SDA (GPIO_PORT0 + 26)
|
|
// #define I2C_SDA (GPIO_PORT0 + 26)
|
|
#define PIN_WIRE_SCL (GPIO_PORT0 + 27)
|
|
// #define I2C_SCL (GPIO_PORT0 + 27)
|
|
|
|
#define PIN_LCD_RESET (GPIO_PORT0 + 2)
|
|
|
|
/*
|
|
* External serial flash WP25R1635FZUIL0
|
|
*/
|
|
|
|
// QSPI Pins
|
|
#define PIN_QSPI_SCK (GPIO_PORT1 + 14)
|
|
#define PIN_QSPI_CS (GPIO_PORT1 + 15)
|
|
#define PIN_QSPI_IO0 (GPIO_PORT1 + 12) // MOSI if using two bit interface
|
|
#define PIN_QSPI_IO1 (GPIO_PORT1 + 13) // MISO if using two bit interface
|
|
#define PIN_QSPI_IO2 (GPIO_PORT0 + 7) // WP if using two bit interface (i.e. not used)
|
|
#define PIN_QSPI_IO3 (GPIO_PORT0 + 5) // HOLD if using two bit interface (i.e. not used)
|
|
|
|
// On-board QSPI Flash
|
|
#define EXTERNAL_FLASH_DEVICES MX25R1635F
|
|
#define EXTERNAL_FLASH_USE_QSPI
|
|
|
|
// Add a delay on startup to allow LoRa and GPS to power up
|
|
#define PIN_PWR_DELAY_MS 100
|
|
|
|
/*
|
|
* Lora radio
|
|
*/
|
|
#define RADIOLIB_DEBUG 1
|
|
#define USE_SX1262
|
|
#define SX126X_CS (GPIO_PORT0 + 24)
|
|
#define SX126X_DIO1 (GPIO_PORT1 + 11)
|
|
// #define SX126X_DIO3 (GPIO_PORT0 + 21)
|
|
// #define SX126X_DIO2 () // LORA_BUSY // LoRa RX/TX
|
|
#define SX126X_BUSY (GPIO_PORT0 + 17)
|
|
#define SX126X_RESET (GPIO_PORT0 + 25)
|
|
#define LORA_RF_PWR (GPIO_PORT0 + 28) // LORA_RF_SWITCH
|
|
|
|
/*
|
|
* GPS pins
|
|
*/
|
|
#define HAS_GPS 1
|
|
#define GPS_UBLOX
|
|
#define GPS_BAUDRATE 38400
|
|
|
|
// #define PIN_GPS_WAKE (GPIO_PORT1 + 2) // An output to wake GPS, low means allow sleep, high means force wake
|
|
// Seems to be missing on this new board
|
|
#define PIN_GPS_PPS (GPIO_PORT1 + 4) // Pulse per second input from the GPS
|
|
#define GPS_TX_PIN (GPIO_PORT1 + 9) // This is for bits going TOWARDS the CPU
|
|
#define GPS_RX_PIN (GPIO_PORT1 + 8) // This is for bits going TOWARDS the GPS
|
|
|
|
#define GPS_THREAD_INTERVAL 50
|
|
|
|
#define PIN_SERIAL1_RX GPS_TX_PIN
|
|
#define PIN_SERIAL1_TX GPS_RX_PIN
|
|
|
|
#define GPS_RESET_PIN (GPIO_PORT1 + 5) // GPS reset pin
|
|
|
|
/*
|
|
* SPI Interfaces
|
|
*/
|
|
#define SPI_INTERFACES_COUNT 1
|
|
|
|
// For LORA, spi 0
|
|
#define PIN_SPI_MISO (GPIO_PORT0 + 23)
|
|
#define PIN_SPI_MOSI (GPIO_PORT0 + 22)
|
|
#define PIN_SPI_SCK (GPIO_PORT0 + 19)
|
|
|
|
// #define PIN_SPI1_MISO (GPIO_PORT1 + 6) // FIXME not really needed, but for now the SPI code requires something to be defined,
|
|
// pick an used GPIO #define PIN_SPI1_MOSI (GPIO_PORT1 + 8) #define PIN_SPI1_SCK (GPIO_PORT1 + 9)
|
|
|
|
#define PIN_PWR_EN (GPIO_PORT0 + 12)
|
|
|
|
// To debug via the segger JLINK console rather than the CDC-ACM serial device
|
|
#define USE_SEGGER 1
|
|
|
|
// #define LORA_DISABLE_SENDING 1
|
|
#define SX126X_DIO2_AS_RF_SWITCH 1
|
|
|
|
// Battery
|
|
// The battery sense is hooked to pin A0 (4)
|
|
// it is defined in the anlaolgue pin section of this file
|
|
// and has 12 bit resolution
|
|
#define BATTERY_SENSE_RESOLUTION_BITS 12
|
|
#define BATTERY_SENSE_RESOLUTION 4096.0
|
|
#undef AREF_VOLTAGE
|
|
#define AREF_VOLTAGE 3.0
|
|
#define VBAT_AR_INTERNAL AR_INTERNAL_3_0
|
|
#define ADC_MULTIPLIER (2.0F)
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
/*----------------------------------------------------------------------------
|
|
* Arduino objects - C++ only
|
|
*----------------------------------------------------------------------------*/
|
|
|
|
#endif |