init
This commit is contained in:
pohui
@@ -0,0 +1,76 @@
|
||||
// Initialize i2c bus on sd_dat and esp_led pins, respectively. We need a bus to not hang on boot
|
||||
#define HAS_SCREEN 0
|
||||
#define I2C_SDA 4
|
||||
#define I2C_SCL 5
|
||||
#define BATTERY_PIN 34
|
||||
#define ADC_CHANNEL ADC1_GPIO34_CHANNEL
|
||||
|
||||
// GPS
|
||||
#undef GPS_RX_PIN
|
||||
#define GPS_RX_PIN NOT_A_PIN
|
||||
#define HAS_GPS 0
|
||||
|
||||
#define BUTTON_PIN 13 // The middle button GPIO on the T-Beam
|
||||
#define BUTTON_NEED_PULLUP
|
||||
#define EXT_NOTIFY_OUT 12 // Overridden default pin to use for Ext Notify Module (#975).
|
||||
|
||||
#define LORA_DIO0 NOT_A_PIN // a No connect on the SX1262/SX1268 module
|
||||
#define LORA_RESET NOT_A_PIN // RST for SX1276, and for SX1262/SX1268
|
||||
#define LORA_DIO3 NOT_A_PIN // Not connected on PCB, but internally on the SX1262/SX1268, if DIO3 is high the TXCO is enabled
|
||||
|
||||
// In transmitting, set TXEN as high communication level，RXEN pin is low level;
|
||||
// In receiving, set RXEN as high communication level, TXEN is lowlevel;
|
||||
// Before powering off, set TXEN、RXEN as low level.
|
||||
|
||||
#undef LORA_SCK
|
||||
#define LORA_SCK 18
|
||||
#undef LORA_MISO
|
||||
#define LORA_MISO 19
|
||||
#undef LORA_MOSI
|
||||
#define LORA_MOSI 23
|
||||
|
||||
// PINS FOR THE 900M22S
|
||||
|
||||
#define LORA_DIO1 26 // IRQ for SX1262/SX1268
|
||||
#define LORA_DIO2 22 // BUSY for SX1262/SX1268
|
||||
// NOT_A_PIN is treated as RADIOLIB_NC due to how they are defined, best to use RADIOLIB_NC directly
|
||||
#define LORA_TXEN RADIOLIB_NC // Input - RF switch TX control, connecting external MCU IO or DIO2, valid in high level
|
||||
// E22_TXEN_CONNECTED_TO_DIO2 wasn't defined, so RXEN wasn't controlled. Commented it out to maintain behavior, but shouldn't be.
|
||||
// Need to comment out defining SX126X_RXEN as LORA_RXEN too
|
||||
// #define LORA_RXEN 17 // Input - RF switch RX control, connecting external MCU IO, valid in high level
|
||||
#undef LORA_CS
|
||||
#define LORA_CS 16
|
||||
#define SX126X_BUSY 22
|
||||
#define SX126X_CS 16
|
||||
|
||||
// PINS FOR THE 900M30S
|
||||
/*
|
||||
#define LORA_DIO1 27 // IRQ for SX1262/SX1268
|
||||
#define LORA_DIO2 35 // BUSY for SX1262/SX1268
|
||||
#define LORA_TXEN NOT_A_PIN // Input - RF switch TX control, connecting external MCU IO or DIO2, valid in high level
|
||||
#define LORA_RXEN 21 // Input - RF switch RX control, connecting external MCU IO, valid in high level
|
||||
#undef LORA_CS
|
||||
#define LORA_CS 33
|
||||
#define SX126X_BUSY 35
|
||||
#define SX126X_CS 33
|
||||
*/
|
||||
|
||||
// RX/TX for RFM95/SX127x
|
||||
// #define RF95_RXEN LORA_RXEN
|
||||
#define RF95_TXEN LORA_TXEN
|
||||
// #define RF95_TCXO <GPIO#>
|
||||
|
||||
// common pinouts for SX126X modules
|
||||
|
||||
#define SX126X_DIO1 LORA_DIO1
|
||||
#define SX126X_RESET LORA_RESET
|
||||
// #define SX126X_RXEN LORA_RXEN
|
||||
#define SX126X_TXEN LORA_TXEN
|
||||
|
||||
// supported modules list
|
||||
// #define USE_RF95 // RFM95/SX127x
|
||||
#define USE_SX1262
|
||||
// #define USE_SX1268
|
||||
// #define USE_LLCC68
|
||||
#define SX126X_DIO2_AS_RF_SWITCH
|
||||
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
||||
@@ -0,0 +1,41 @@
|
||||
// For OLED LCD
|
||||
#define I2C_SDA 21
|
||||
#define I2C_SCL 22
|
||||
|
||||
// For GPS, 'undef's not needed
|
||||
#define GPS_TX_PIN 15
|
||||
#define GPS_RX_PIN 12
|
||||
#define PIN_GPS_EN 4
|
||||
#define GPS_POWER_TOGGLE // Moved definition from platformio.ini to here
|
||||
|
||||
#define BUTTON_PIN 39 // The middle button GPIO on the T-Beam
|
||||
#define BATTERY_PIN 35 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
|
||||
#define ADC_CHANNEL ADC1_GPIO35_CHANNEL
|
||||
#define ADC_MULTIPLIER 1.85 // (R1 = 470k, R2 = 680k)
|
||||
#define EXT_PWR_DETECT 4 // Pin to detect connected external power source for LILYGO® TTGO T-Energy T18 and other DIY boards
|
||||
#define EXT_NOTIFY_OUT 12 // Overridden default pin to use for Ext Notify Module (#975).
|
||||
#define LED_PIN 2 // add status LED (compatible with core-pcb and DIY targets)
|
||||
|
||||
// Radio
|
||||
#define USE_SX1262 // E22-900M30S uses SX1262
|
||||
#define USE_SX1268 // E22-400M30S uses SX1268
|
||||
#define SX126X_MAX_POWER \
|
||||
22 // Outputting 22dBm from SX1262 results in ~30dBm E22-900M30S output (module only uses last stage of the YP2233W PA)
|
||||
#define SX126X_DIO3_TCXO_VOLTAGE 1.8 // E22 series TCXO reference voltage is 1.8V
|
||||
|
||||
#define SX126X_CS 18 // EBYTE module's NSS pin
|
||||
#define SX126X_SCK 5 // EBYTE module's SCK pin
|
||||
#define SX126X_MOSI 27 // EBYTE module's MOSI pin
|
||||
#define SX126X_MISO 19 // EBYTE module's MISO pin
|
||||
#define SX126X_RESET 23 // EBYTE module's NRST pin
|
||||
#define SX126X_BUSY 32 // EBYTE module's BUSY pin
|
||||
#define SX126X_DIO1 33 // EBYTE module's DIO1 pin
|
||||
|
||||
#define SX126X_TXEN 13 // Schematic connects EBYTE module's TXEN pin to MCU
|
||||
#define SX126X_RXEN 14 // Schematic connects EBYTE module's RXEN pin to MCU
|
||||
|
||||
#define LORA_CS SX126X_CS // Compatibility with variant file configuration structure
|
||||
#define LORA_SCK SX126X_SCK // Compatibility with variant file configuration structure
|
||||
#define LORA_MOSI SX126X_MOSI // Compatibility with variant file configuration structure
|
||||
#define LORA_MISO SX126X_MISO // Compatibility with variant file configuration structure
|
||||
#define LORA_DIO1 SX126X_DIO1 // Compatibility with variant file configuration structure
|
||||
@@ -0,0 +1,49 @@
|
||||
#ifndef _VARIANT_MESHTAB_DIY_
|
||||
#define _VARIANT_MESHTAB_DIY_
|
||||
|
||||
#define HAS_TOUCHSCREEN 1
|
||||
|
||||
#define SLEEP_TIME 120
|
||||
|
||||
// Analog pins
|
||||
#define BATTERY_PIN 4 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
|
||||
// ratio of voltage divider = 2.0
|
||||
#define ADC_MULTIPLIER 2.11 // 2.0 + 10% for correction of display undervoltage.
|
||||
#define ADC_CHANNEL ADC1_GPIO4_CHANNEL
|
||||
|
||||
// LED
|
||||
#define LED_PIN 21
|
||||
|
||||
// Button
|
||||
#define BUTTON_PIN 0
|
||||
|
||||
// GPS
|
||||
#define GPS_RX_PIN 18
|
||||
#define GPS_TX_PIN 17
|
||||
|
||||
// #define HAS_SDCARD 1
|
||||
#define SPI_MOSI 13
|
||||
#define SPI_SCK 12
|
||||
#define SPI_MISO 11
|
||||
#define SPI_CS 10
|
||||
#define SDCARD_CS 6
|
||||
|
||||
// LORA SPI
|
||||
#define LORA_SCK 36
|
||||
#define LORA_MISO 37
|
||||
#define LORA_MOSI 35
|
||||
#define LORA_CS 39
|
||||
|
||||
// LORA MODULES
|
||||
#define USE_SX1262
|
||||
|
||||
// LORA CONFIG
|
||||
#define SX126X_CS LORA_CS
|
||||
#define SX126X_DIO1 15
|
||||
#define SX126X_DIO2_AS_RF_SWITCH
|
||||
#define SX126X_BUSY 40
|
||||
#define SX126X_RESET 14
|
||||
#define SX126X_RXEN 47
|
||||
#define SX126X_TXEN RADIOLIB_NC // Assuming that DIO2 is connected to TXEN pin
|
||||
|
||||
#endif
|
||||
@@ -0,0 +1,38 @@
|
||||
/*
|
||||
Copyright (c) 2014-2015 Arduino LLC. All right reserved.
|
||||
Copyright (c) 2016 Sandeep Mistry All right reserved.
|
||||
Copyright (c) 2018, Adafruit Industries (adafruit.com)
|
||||
|
||||
This library is free software; you can redistribute it and/or
|
||||
modify it under the terms of the GNU Lesser General Public
|
||||
License as published by the Free Software Foundation; either
|
||||
version 2.1 of the License, or (at your option) any later version.
|
||||
|
||||
This library is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
||||
See the GNU Lesser General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU Lesser General Public
|
||||
License along with this library; if not, write to the Free Software
|
||||
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
|
||||
*/
|
||||
|
||||
#include "variant.h"
|
||||
#include "nrf.h"
|
||||
#include "wiring_constants.h"
|
||||
#include "wiring_digital.h"
|
||||
|
||||
const uint32_t g_ADigitalPinMap[] = {
|
||||
// P0
|
||||
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31,
|
||||
|
||||
// P1
|
||||
32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47};
|
||||
|
||||
void initVariant()
|
||||
{
|
||||
// 3V3 Power Rail
|
||||
pinMode(PIN_3V3_EN, OUTPUT);
|
||||
digitalWrite(PIN_3V3_EN, HIGH);
|
||||
}
|
||||
@@ -0,0 +1,182 @@
|
||||
#ifndef _VARIANT_PROMICRO_DIY_
|
||||
#define _VARIANT_PROMICRO_DIY_
|
||||
|
||||
/** Master clock frequency */
|
||||
#define VARIANT_MCK (64000000ul)
|
||||
|
||||
// #define USE_LFXO // Board uses 32khz crystal for LF
|
||||
#define USE_LFRC // Board uses RC for LF
|
||||
|
||||
#define PROMICRO_DIY_TCXO
|
||||
|
||||
/*----------------------------------------------------------------------------
|
||||
* Headers
|
||||
*----------------------------------------------------------------------------*/
|
||||
|
||||
#include "WVariant.h"
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif // __cplusplus
|
||||
|
||||
/*
|
||||
NRF52 PRO MICRO PIN ASSIGNMENT
|
||||
|
||||
| Pin | Function | | Pin | Function | RF95 |
|
||||
| ----- | ----------- | --- | -------- | ------------ | ----- |
|
||||
| Gnd | | | vbat | | |
|
||||
| P0.06 | Serial2 RX | | vbat | | |
|
||||
| P0.08 | Serial2 TX | | Gnd | | |
|
||||
| Gnd | | | reset | | |
|
||||
| Gnd | | | ext_vcc | *see 0.13 | |
|
||||
| P0.17 | RXEN | | P0.31 | BATTERY_PIN | |
|
||||
| P0.20 | GPS_RX | | P0.29 | BUSY | DIO0 |
|
||||
| P0.22 | GPS_TX | | P0.02 | MISO | MISO |
|
||||
| P0.24 | GPS_EN | | P1.15 | MOSI | MOSI |
|
||||
| P1.00 | BUTTON_PIN | | P1.13 | CS | CS |
|
||||
| P0.11 | SCL | | P1.11 | SCK | SCK |
|
||||
| P1.04 | SDA | | P0.10 | DIO1/IRQ | DIO1 |
|
||||
| P1.06 | Free pin | | P0.09 | RESET | RST |
|
||||
| | | | | | |
|
||||
| | Mid board | | | Internal | |
|
||||
| P1.01 | Free pin | | 0.15 | LED | |
|
||||
| P1.02 | Free pin | | 0.13 | 3V3_EN | |
|
||||
| P1.07 | Free pin | | | | |
|
||||
*/
|
||||
|
||||
// Number of pins defined in PinDescription array
|
||||
#define PINS_COUNT (48)
|
||||
#define NUM_DIGITAL_PINS (48)
|
||||
#define NUM_ANALOG_INPUTS (1)
|
||||
#define NUM_ANALOG_OUTPUTS (0)
|
||||
|
||||
// Pin 13 enables 3.3V periphery. If the Lora module is on this pin, then it should stay enabled at all times.
|
||||
#define PIN_3V3_EN (0 + 13) // P0.13
|
||||
|
||||
// Analog pins
|
||||
#define BATTERY_PIN (0 + 31) // P0.31 Battery ADC
|
||||
#define ADC_CHANNEL ADC1_GPIO4_CHANNEL
|
||||
#define ADC_RESOLUTION 14
|
||||
#define BATTERY_SENSE_RESOLUTION_BITS 12
|
||||
#define BATTERY_SENSE_RESOLUTION 4096.0
|
||||
// Definition of milliVolt per LSB => 3.0V ADC range and 12-bit ADC resolution = 3000mV/4096
|
||||
#define VBAT_MV_PER_LSB (0.73242188F)
|
||||
// Voltage divider value => 1.5M + 1M voltage divider on VBAT = (1.5M / (1M + 1.5M))
|
||||
#define VBAT_DIVIDER (0.6F)
|
||||
// Compensation factor for the VBAT divider
|
||||
#define VBAT_DIVIDER_COMP (1.73)
|
||||
// Fixed calculation of milliVolt from compensation value
|
||||
#define REAL_VBAT_MV_PER_LSB (VBAT_DIVIDER_COMP * VBAT_MV_PER_LSB)
|
||||
#undef AREF_VOLTAGE
|
||||
#define AREF_VOLTAGE 3.0
|
||||
#define VBAT_AR_INTERNAL AR_INTERNAL_3_0
|
||||
#define ADC_MULTIPLIER VBAT_DIVIDER_COMP // REAL_VBAT_MV_PER_LSB
|
||||
#define VBAT_RAW_TO_SCALED(x) (REAL_VBAT_MV_PER_LSB * x)
|
||||
|
||||
// WIRE IC AND IIC PINS
|
||||
#define WIRE_INTERFACES_COUNT 1
|
||||
|
||||
#define PIN_WIRE_SDA (32 + 4) // P1.04
|
||||
#define PIN_WIRE_SCL (0 + 11) // P0.11
|
||||
|
||||
// LED
|
||||
#define PIN_LED1 (0 + 15) // P0.15
|
||||
#define LED_BUILTIN PIN_LED1
|
||||
// Actually red
|
||||
#define LED_BLUE PIN_LED1
|
||||
#define LED_STATE_ON 1 // State when LED is lit
|
||||
|
||||
// Button
|
||||
#define BUTTON_PIN (32 + 0) // P1.00
|
||||
|
||||
// GPS
|
||||
#define PIN_GPS_TX (0 + 22) // P0.22
|
||||
#define PIN_GPS_RX (0 + 20) // P0.20
|
||||
|
||||
#define PIN_GPS_EN (0 + 24) // P0.24
|
||||
#define GPS_POWER_TOGGLE
|
||||
#define GPS_UBLOX
|
||||
// define GPS_DEBUG
|
||||
|
||||
// UART interfaces
|
||||
#define PIN_SERIAL1_RX PIN_GPS_TX
|
||||
#define PIN_SERIAL1_TX PIN_GPS_RX
|
||||
|
||||
#define PIN_SERIAL2_RX (0 + 6) // P0.06
|
||||
#define PIN_SERIAL2_TX (0 + 8) // P0.08
|
||||
|
||||
// Serial interfaces
|
||||
#define SPI_INTERFACES_COUNT 1
|
||||
|
||||
#define PIN_SPI_MISO (0 + 2) // P0.02
|
||||
#define PIN_SPI_MOSI (32 + 15) // P1.15
|
||||
#define PIN_SPI_SCK (32 + 11) // P1.11
|
||||
|
||||
#define LORA_MISO PIN_SPI_MISO
|
||||
#define LORA_MOSI PIN_SPI_MOSI
|
||||
#define LORA_SCK PIN_SPI_SCK
|
||||
#define LORA_CS (32 + 13) // P1.13
|
||||
|
||||
// LORA MODULES
|
||||
#define USE_LLCC68
|
||||
#define USE_SX1262
|
||||
#define USE_RF95
|
||||
#define USE_SX1268
|
||||
|
||||
// RF95 CONFIG
|
||||
|
||||
#define LORA_DIO0 (0 + 29) // P0.10 IRQ
|
||||
#define LORA_DIO1 (0 + 10) // P0.10 IRQ
|
||||
#define LORA_RESET (0 + 9) // P0.09
|
||||
|
||||
// RX/TX for RFM95/SX127x
|
||||
#define RF95_RXEN (0 + 17) // P0.17
|
||||
#define RF95_TXEN RADIOLIB_NC // Assuming that DIO2 is connected to TXEN pin. If not, TXEN must be connected.
|
||||
|
||||
// SX126X CONFIG
|
||||
#define SX126X_CS (32 + 13) // P1.13 FIXME - we really should define LORA_CS instead
|
||||
#define SX126X_DIO1 (0 + 10) // P0.10 IRQ
|
||||
#define SX126X_DIO2_AS_RF_SWITCH // Note for E22 modules: DIO2 is not attached internally to TXEN for automatic TX/RX switching,
|
||||
// so it needs connecting externally if it is used in this way
|
||||
#define SX126X_BUSY (0 + 29) // P0.29
|
||||
#define SX126X_RESET (0 + 9) // P0.09
|
||||
#define SX126X_RXEN (0 + 17) // P0.17
|
||||
#define SX126X_TXEN RADIOLIB_NC // Assuming that DIO2 is connected to TXEN pin. If not, TXEN must be connected.
|
||||
|
||||
// #define SX126X_MAX_POWER 8 set this if using a high-power board!
|
||||
|
||||
/*
|
||||
On the SX1262, DIO3 sets the voltage for an external TCXO, if one is present. If one is not present, use TCXO_OPTIONAL to try both
|
||||
settings.
|
||||
|
||||
| Mfr | Module | TCXO | RF Switch | Notes |
|
||||
| ------------ | ---------------- | ---- | --------- | ------------------------------------- |
|
||||
| Ebyte | E22-900M22S | Yes | Ext | |
|
||||
| Ebyte | E22-900MM22S | No | Ext | |
|
||||
| Ebyte | E22-900M30S | Yes | Ext | |
|
||||
| Ebyte | E22-900M33S | Yes | Ext | MAX_POWER must be set to 8 for this |
|
||||
| Ebyte | E220-900M22S | No | Ext | LLCC68, looks like DIO3 not connected |
|
||||
| AI-Thinker | RA-01SH | No | Int | SX1262 |
|
||||
| Heltec | HT-RA62 | Yes | Int | |
|
||||
| NiceRF | Lora1262 | yes | Int | |
|
||||
| Waveshare | Core1262-HF | yes | Ext | |
|
||||
| Waveshare | LoRa Node Module | yes | Int | |
|
||||
| Seeed | Wio-SX1262 | yes | Int | Sooooo cute! |
|
||||
| AI-Thinker | RA-02 | No | Int | SX1278 **433mhz band only** |
|
||||
| RF Solutions | RFM95 | No | Int | Untested |
|
||||
|
||||
*/
|
||||
|
||||
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
||||
#define TCXO_OPTIONAL // make it so that the firmware can try both TCXO and XTAL
|
||||
extern float tcxoVoltage; // make this available everywhere
|
||||
|
||||
#ifdef __cplusplus
|
||||
}
|
||||
#endif
|
||||
|
||||
/*----------------------------------------------------------------------------
|
||||
* Arduino objects - C++ only
|
||||
*----------------------------------------------------------------------------*/
|
||||
|
||||
#endif
|
||||
@@ -0,0 +1,38 @@
|
||||
/*
|
||||
Copyright (c) 2014-2015 Arduino LLC. All right reserved.
|
||||
Copyright (c) 2016 Sandeep Mistry All right reserved.
|
||||
Copyright (c) 2018, Adafruit Industries (adafruit.com)
|
||||
|
||||
This library is free software; you can redistribute it and/or
|
||||
modify it under the terms of the GNU Lesser General Public
|
||||
License as published by the Free Software Foundation; either
|
||||
version 2.1 of the License, or (at your option) any later version.
|
||||
|
||||
This library is distributed in the hope that it will be useful,
|
||||
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
||||
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.
|
||||
See the GNU Lesser General Public License for more details.
|
||||
|
||||
You should have received a copy of the GNU Lesser General Public
|
||||
License along with this library; if not, write to the Free Software
|
||||
Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
|
||||
*/
|
||||
|
||||
#include "variant.h"
|
||||
#include "nrf.h"
|
||||
#include "wiring_constants.h"
|
||||
#include "wiring_digital.h"
|
||||
|
||||
const uint32_t g_ADigitalPinMap[] = {
|
||||
// P0
|
||||
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27, 28, 29, 30, 31,
|
||||
|
||||
// P1
|
||||
32, 33, 34, 35, 36, 37, 38, 39, 40, 41, 42, 43, 44, 45, 46, 47};
|
||||
|
||||
void initVariant()
|
||||
{
|
||||
// 3V3 Power Rail
|
||||
pinMode(PIN_3V3_EN, OUTPUT);
|
||||
digitalWrite(PIN_3V3_EN, HIGH);
|
||||
}
|
||||
@@ -0,0 +1,155 @@
|
||||
#ifndef _VARIANT_PROMICRO_DIY_
|
||||
#define _VARIANT_PROMICRO_DIY_
|
||||
|
||||
/** Master clock frequency */
|
||||
#define VARIANT_MCK (64000000ul)
|
||||
|
||||
// #define USE_LFXO // Board uses 32khz crystal for LF
|
||||
#define USE_LFRC // Board uses RC for LF
|
||||
|
||||
#define PROMICRO_DIY_XTAL
|
||||
/*----------------------------------------------------------------------------
|
||||
* Headers
|
||||
*----------------------------------------------------------------------------*/
|
||||
|
||||
#include "WVariant.h"
|
||||
|
||||
#ifdef __cplusplus
|
||||
extern "C" {
|
||||
#endif // __cplusplus
|
||||
|
||||
/*
|
||||
NRF52 PRO MICRO PIN ASSIGNMENT
|
||||
|
||||
| Pin | Function | | Pin | Function |
|
||||
|-------|------------|---|---------|-------------|
|
||||
| Gnd | | | vbat | |
|
||||
| P0.06 | Serial2 RX | | vbat | |
|
||||
| P0.08 | Serial2 TX | | Gnd | |
|
||||
| Gnd | | | reset | |
|
||||
| Gnd | | | ext_vcc | *see 0.13 |
|
||||
| P0.17 | RXEN | | P0.31 | BATTERY_PIN |
|
||||
| P0.20 | GPS_RX | | P0.29 | BUSY |
|
||||
| P0.22 | GPS_TX | | P0.02 | MISO |
|
||||
| P0.24 | GPS_EN | | P1.15 | MOSI |
|
||||
| P1.00 | BUTTON_PIN | | P1.13 | CS |
|
||||
| P0.11 | SCL | | P1.11 | SCK |
|
||||
| P1.04 | SDA | | P0.10 | DIO1/IRQ |
|
||||
| P1.06 | Free pin | | P0.09 | RESET |
|
||||
| | | | | |
|
||||
| | Mid board | | | Internal |
|
||||
| P1.01 | Free pin | | 0.15 | LED |
|
||||
| P1.02 | Free pin | | 0.13 | 3V3_EN |
|
||||
| P1.07 | Free pin | | | |
|
||||
*/
|
||||
|
||||
// Number of pins defined in PinDescription array
|
||||
#define PINS_COUNT (48)
|
||||
#define NUM_DIGITAL_PINS (48)
|
||||
#define NUM_ANALOG_INPUTS (1)
|
||||
#define NUM_ANALOG_OUTPUTS (0)
|
||||
|
||||
// Pin 13 enables 3.3V periphery. If the Lora module is on this pin, then it should stay enabled at all times.
|
||||
#define PIN_3V3_EN (0 + 13) // P0.13
|
||||
|
||||
// Analog pins
|
||||
#define BATTERY_PIN (0 + 31) // P0.31 Battery ADC
|
||||
#define ADC_CHANNEL ADC1_GPIO4_CHANNEL
|
||||
#define ADC_RESOLUTION 14
|
||||
#define BATTERY_SENSE_RESOLUTION_BITS 12
|
||||
#define BATTERY_SENSE_RESOLUTION 4096.0
|
||||
// Definition of milliVolt per LSB => 3.0V ADC range and 12-bit ADC resolution = 3000mV/4096
|
||||
#define VBAT_MV_PER_LSB (0.73242188F)
|
||||
// Voltage divider value => 1.5M + 1M voltage divider on VBAT = (1.5M / (1M + 1.5M))
|
||||
#define VBAT_DIVIDER (0.6F)
|
||||
// Compensation factor for the VBAT divider
|
||||
#define VBAT_DIVIDER_COMP (1.73)
|
||||
// Fixed calculation of milliVolt from compensation value
|
||||
#define REAL_VBAT_MV_PER_LSB (VBAT_DIVIDER_COMP * VBAT_MV_PER_LSB)
|
||||
#undef AREF_VOLTAGE
|
||||
#define AREF_VOLTAGE 3.0
|
||||
#define VBAT_AR_INTERNAL AR_INTERNAL_3_0
|
||||
#define ADC_MULTIPLIER VBAT_DIVIDER_COMP // REAL_VBAT_MV_PER_LSB
|
||||
#define VBAT_RAW_TO_SCALED(x) (REAL_VBAT_MV_PER_LSB * x)
|
||||
|
||||
// WIRE IC AND IIC PINS
|
||||
#define WIRE_INTERFACES_COUNT 1
|
||||
|
||||
#define PIN_WIRE_SDA (32 + 4) // P1.04
|
||||
#define PIN_WIRE_SCL (0 + 11) // P0.11
|
||||
|
||||
// LED
|
||||
#define PIN_LED1 (0 + 15) // P0.15
|
||||
#define LED_BUILTIN PIN_LED1
|
||||
// Actually red
|
||||
#define LED_BLUE PIN_LED1
|
||||
#define LED_STATE_ON 1 // State when LED is lit
|
||||
|
||||
// Button
|
||||
#define BUTTON_PIN (32 + 0) // P1.00
|
||||
|
||||
// GPS
|
||||
#define PIN_GPS_TX (0 + 22) // P0.22
|
||||
#define PIN_GPS_RX (0 + 20) // P0.20
|
||||
|
||||
#define PIN_GPS_EN (0 + 24) // P0.24
|
||||
#define GPS_POWER_TOGGLE
|
||||
#define GPS_UBLOX
|
||||
// define GPS_DEBUG
|
||||
|
||||
// UART interfaces
|
||||
#define PIN_SERIAL1_RX PIN_GPS_TX
|
||||
#define PIN_SERIAL1_TX PIN_GPS_RX
|
||||
|
||||
#define PIN_SERIAL2_RX (0 + 6) // P0.06
|
||||
#define PIN_SERIAL2_TX (0 + 8) // P0.08
|
||||
|
||||
// Serial interfaces
|
||||
#define SPI_INTERFACES_COUNT 1
|
||||
|
||||
#define PIN_SPI_MISO (0 + 2) // P0.02
|
||||
#define PIN_SPI_MOSI (32 + 15) // P1.15
|
||||
#define PIN_SPI_SCK (32 + 11) // P1.11
|
||||
|
||||
// LORA MODULES
|
||||
#define USE_LLCC68
|
||||
#define USE_SX1262
|
||||
// #define USE_RF95
|
||||
#define USE_SX1268
|
||||
|
||||
// LORA CONFIG
|
||||
#define SX126X_CS (32 + 13) // P1.13 FIXME - we really should define LORA_CS instead
|
||||
#define SX126X_DIO1 (0 + 10) // P0.10 IRQ
|
||||
#define SX126X_DIO2_AS_RF_SWITCH // Note for E22 modules: DIO2 is not attached internally to TXEN for automatic TX/RX switching,
|
||||
// so it needs connecting externally if it is used in this way
|
||||
#define SX126X_BUSY (0 + 29) // P0.29
|
||||
#define SX126X_RESET (0 + 9) // P0.09
|
||||
#define SX126X_RXEN (0 + 17) // P0.17
|
||||
#define SX126X_TXEN RADIOLIB_NC // Assuming that DIO2 is connected to TXEN pin. If not, TXEN must be connected.
|
||||
|
||||
/*
|
||||
On the SX1262, DIO3 sets the voltage for an external TCXO, if one is present. If one is not present, then this should not be used.
|
||||
|
||||
Ebyte
|
||||
e22-900mm22s has no TCXO
|
||||
e22-900m22s has TCXO
|
||||
e220-900mm22s has no TCXO, works with/without this definition, looks like DIO3 not connected at all
|
||||
|
||||
AI-thinker
|
||||
RA-01SH does not have TCXO
|
||||
|
||||
Waveshare
|
||||
Core1262 has TCXO
|
||||
|
||||
*/
|
||||
// #define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
||||
|
||||
#ifdef __cplusplus
|
||||
}
|
||||
#endif
|
||||
|
||||
/*----------------------------------------------------------------------------
|
||||
* Arduino objects - C++ only
|
||||
*----------------------------------------------------------------------------*/
|
||||
|
||||
#endif
|
||||
@@ -0,0 +1,160 @@
|
||||
; Meshtastic DIY v1 by Nano VHF Schematic based on ESP32-WROOM-32 (38 pins) devkit & EBYTE E22 SX1262/SX1268 module
|
||||
[env:meshtastic-diy-v1]
|
||||
extends = esp32_base
|
||||
board = esp32doit-devkit-v1
|
||||
board_check = true
|
||||
build_flags =
|
||||
${esp32_base.build_flags}
|
||||
-D DIY_V1
|
||||
-D EBYTE_E22
|
||||
-I variants/diy/v1
|
||||
|
||||
; Meshtastic DIY v1.1 new schematic based on ESP32-WROOM-32 & SX1262/SX1268 modules
|
||||
[env:meshtastic-diy-v1_1]
|
||||
extends = esp32_base
|
||||
board = esp32doit-devkit-v1
|
||||
board_level = extra
|
||||
build_flags =
|
||||
${esp32_base.build_flags}
|
||||
-D DIY_V1
|
||||
-D EBYTE_E22
|
||||
-I variants/diy/v1_1
|
||||
|
||||
; Port to Disaster Radio's ESP32-v3 Dev Board
|
||||
[env:meshtastic-dr-dev]
|
||||
extends = esp32_base
|
||||
board = esp32doit-devkit-v1
|
||||
board_upload.maximum_size = 4194304
|
||||
board_upload.maximum_ram_size = 532480
|
||||
build_flags =
|
||||
${esp32_base.build_flags}
|
||||
-D DR_DEV
|
||||
-D EBYTE_E22
|
||||
-I variants/diy/dr-dev
|
||||
|
||||
; Hydra - Meshtastic DIY v1 hardware with some specific changes
|
||||
[env:hydra]
|
||||
extends = esp32_base
|
||||
board = esp32doit-devkit-v1
|
||||
build_flags =
|
||||
${esp32_base.build_flags}
|
||||
-D DIY_V1
|
||||
-I variants/diy/hydra
|
||||
|
||||
|
||||
; Promicro + E22(0)-xxxMM / RA-01SH modules board variant - DIY - without TCXO
|
||||
[env:nrf52_promicro_diy_xtal]
|
||||
extends = nrf52840_base
|
||||
board = promicro-nrf52840
|
||||
board_level = extra
|
||||
build_flags = ${nrf52840_base.build_flags}
|
||||
-I variants/diy/nrf52_promicro_diy_xtal
|
||||
-D NRF52_PROMICRO_DIY
|
||||
-L "${platformio.libdeps_dir}/${this.__env__}/bsec2/src/cortex-m4/fpv4-sp-d16-hard"
|
||||
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/diy/nrf52_promicro_diy_xtal>
|
||||
lib_deps =
|
||||
${nrf52840_base.lib_deps}
|
||||
debug_tool = jlink
|
||||
|
||||
|
||||
; Promicro + E22(0)-xxxM / HT-RA62 modules board variant - DIY - with TCXO
|
||||
[env:nrf52_promicro_diy_tcxo]
|
||||
extends = nrf52840_base
|
||||
board = promicro-nrf52840
|
||||
board_level = extra
|
||||
build_flags = ${nrf52840_base.build_flags}
|
||||
-I variants/diy/nrf52_promicro_diy_tcxo
|
||||
-D NRF52_PROMICRO_DIY
|
||||
-L "${platformio.libdeps_dir}/${this.__env__}/bsec2/src/cortex-m4/fpv4-sp-d16-hard"
|
||||
build_src_filter = ${nrf52_base.build_src_filter} +<../variants/diy/nrf52_promicro_diy_tcxo>
|
||||
lib_deps =
|
||||
${nrf52840_base.lib_deps}
|
||||
debug_tool = jlink
|
||||
|
||||
; NanoVHF T-Energy-S3 + E22(0)-xxxM - DIY
|
||||
[env:t-energy-s3_e22]
|
||||
extends = esp32s3_base
|
||||
board = esp32-s3-devkitc-1
|
||||
board_level = extra
|
||||
board_upload.flash_size = 16MB ;Specify the FLASH capacity as 16MB
|
||||
board_build.arduino.memory_type = qio_opi ;Enable internal PSRAM
|
||||
build_unflags =
|
||||
${esp32s3_base.build_unflags}
|
||||
-D ARDUINO_USB_MODE=1
|
||||
build_flags =
|
||||
${esp32s3_base.build_flags}
|
||||
-D EBYTE_ESP32_S3
|
||||
-D BOARD_HAS_PSRAM
|
||||
-D ARDUINO_USB_MODE=0
|
||||
-D ARDUINO_USB_CDC_ON_BOOT=1
|
||||
-I variants/diy/t-energy-s3_e22
|
||||
|
||||
; esp32-s3 + ra-sh01 lora + 3.2" ILI9143
|
||||
[env:mesh-tab]
|
||||
extends = esp32s3_base
|
||||
board = um_feathers3
|
||||
board_level = extra
|
||||
board_upload.flash_size = 16MB
|
||||
board_build.partitions = default_16MB.csv
|
||||
upload_protocol = esptool
|
||||
build_flags = ${esp32s3_base.build_flags}
|
||||
-D MESH_TAB
|
||||
-D PRIVATE_HW
|
||||
-D CONFIG_ARDUHAL_ESP_LOG
|
||||
-D CONFIG_ARDUHAL_LOG_COLORS=1
|
||||
-D CONFIG_DISABLE_HAL_LOCKS=1 ; "feels" to be a bit more stable without locks
|
||||
-D MESHTASTIC_EXCLUDE_CANNEDMESSAGES=1
|
||||
-D MESHTASTIC_EXCLUDE_INPUTBROKER=1
|
||||
-D MESHTASTIC_EXCLUDE_BLUETOOTH=1
|
||||
-D MESHTASTIC_EXCLUDE_WEBSERVER=1
|
||||
-D LV_LVGL_H_INCLUDE_SIMPLE
|
||||
-D LV_CONF_INCLUDE_SIMPLE
|
||||
-D LV_COMP_CONF_INCLUDE_SIMPLE
|
||||
-D LV_USE_SYSMON=0
|
||||
-D LV_USE_PROFILER=0
|
||||
-D LV_USE_PERF_MONITOR=0
|
||||
-D LV_USE_MEM_MONITOR=0
|
||||
-D LV_USE_LOG=0
|
||||
-D LV_BUILD_TEST=0
|
||||
-D USE_LOG_DEBUG
|
||||
-D LOG_DEBUG_INC=\"DebugConfiguration.h\"
|
||||
-D RADIOLIB_SPI_PARANOID=0
|
||||
-D MAX_NUM_NODES=250
|
||||
-D MAX_THREADS=40
|
||||
-D HAS_SCREEN=0
|
||||
-D HAS_TFT=1
|
||||
-D RAM_SIZE=1024
|
||||
-D LGFX_DRIVER_TEMPLATE
|
||||
-D LGFX_DRIVER=LGFX_GENERIC
|
||||
-D LGFX_PANEL=ILI9341
|
||||
-D LGFX_OFFSET_ROTATION=1
|
||||
-D LGFX_TOUCH=XPT2046
|
||||
-D LGFX_PIN_SCK=12
|
||||
-D LGFX_PIN_MOSI=13
|
||||
-D LGFX_PIN_MISO=11
|
||||
-D LGFX_PIN_DC=16
|
||||
-D LGFX_PIN_CS=10
|
||||
-D LGFX_PIN_RST=-1
|
||||
-D LGFX_PIN_BL=42
|
||||
-D LGFX_TOUCH_INT=41
|
||||
-D LGFX_TOUCH_CS=7
|
||||
-D LGFX_TOUCH_CLK=12
|
||||
-D LGFX_TOUCH_DO=11
|
||||
-D LGFX_TOUCH_DIN=13
|
||||
-D LGFX_TOUCH_X_MIN=300
|
||||
-D LGFX_TOUCH_X_MAX=3900
|
||||
-D LGFX_TOUCH_Y_MIN=400
|
||||
-D LGFX_TOUCH_Y_MAX=3900
|
||||
-D VIEW_320x240
|
||||
-D USE_PACKET_API
|
||||
-I lib/device-ui/generated/ui_320x240
|
||||
-I variants/diy/mesh-tab
|
||||
build_src_filter = ${esp32_base.build_src_filter}
|
||||
+<../lib/device-ui/generated/ui_320x240>
|
||||
+<../lib/device-ui/resources>
|
||||
+<../lib/device-ui/locale>
|
||||
+<../lib/device-ui/source>
|
||||
lib_deps = ${esp32_base.lib_deps}
|
||||
lovyan03/LovyanGFX@^1.1.16
|
||||
earlephilhower/ESP8266Audio@^1.9.7
|
||||
earlephilhower/ESP8266SAM@^1.0.1
|
||||
@@ -0,0 +1,46 @@
|
||||
// NanoVHF T-Energy-S3 + E22(0)-xxxM - DIY
|
||||
// https://github.com/NanoVHF/Meshtastic-DIY/tree/main/PCB/ESP-32-devkit_EBYTE-E22/Mesh-v1.06-TTGO-T18
|
||||
|
||||
// Battery
|
||||
#define BATTERY_PIN 3
|
||||
#define ADC_MULTIPLIER 2.0
|
||||
#define ADC_CHANNEL ADC1_GPIO3_CHANNEL
|
||||
|
||||
// Button on NanoVHF PCB
|
||||
#define BUTTON_PIN 39
|
||||
|
||||
// I2C via connectors on NanoVHF PCB
|
||||
#define I2C_SCL 2
|
||||
#define I2C_SDA 42
|
||||
|
||||
// Screen (disabled)
|
||||
#define HAS_SCREEN 0 // Assume no screen present by default to prevent crash...
|
||||
|
||||
// GPS via T-Energy-S3 onboard connector
|
||||
#define HAS_GPS 1
|
||||
#define GPS_TX_PIN 43
|
||||
#define GPS_RX_PIN 44
|
||||
|
||||
// LoRa
|
||||
#define USE_SX1262 // E22-900M30S, E22-900M22S, and E22-900MM22S (not E220!) use SX1262
|
||||
#define USE_SX1268 // E22-400M30S, E22-400M33S, E22-400M22S, and E22-400MM22S use SX1268
|
||||
|
||||
#define SX126X_MAX_POWER 22 // SX126xInterface.cpp defaults to 22 if not defined, but here we define it for good practice
|
||||
#define SX126X_DIO3_TCXO_VOLTAGE 1.8 // E22 series TCXO reference voltage is 1.8V
|
||||
|
||||
#define SX126X_CS 5 // EBYTE module's NSS pin // FIXME: rename to SX126X_SS
|
||||
#define SX126X_SCK 6 // EBYTE module's SCK pin
|
||||
#define SX126X_MOSI 13 // EBYTE module's MOSI pin
|
||||
#define SX126X_MISO 4 // EBYTE module's MISO pin
|
||||
#define SX126X_RESET 1 // EBYTE module's NRST pin
|
||||
#define SX126X_BUSY 48 // EBYTE module's BUSY pin
|
||||
#define SX126X_DIO1 47 // EBYTE module's DIO1 pin
|
||||
|
||||
#define SX126X_TXEN 10 // Schematic connects EBYTE module's TXEN pin to MCU
|
||||
#define SX126X_RXEN 12 // Schematic connects EBYTE module's RXEN pin to MCU
|
||||
|
||||
#define LORA_CS SX126X_CS // Compatibility with variant file configuration structure
|
||||
#define LORA_SCK SX126X_SCK // Compatibility with variant file configuration structure
|
||||
#define LORA_MOSI SX126X_MOSI // Compatibility with variant file configuration structure
|
||||
#define LORA_MISO SX126X_MISO // Compatibility with variant file configuration structure
|
||||
#define LORA_DIO1 SX126X_DIO1 // Compatibility with variant file configuration structure
|
||||
@@ -0,0 +1,56 @@
|
||||
// For OLED LCD
|
||||
#define I2C_SDA 21
|
||||
#define I2C_SCL 22
|
||||
|
||||
// GPS
|
||||
#undef GPS_RX_PIN
|
||||
#undef GPS_TX_PIN
|
||||
#define GPS_RX_PIN 12
|
||||
#define GPS_TX_PIN 15
|
||||
#define GPS_UBLOX
|
||||
|
||||
#define BUTTON_PIN 39 // The middle button GPIO on the T-Beam
|
||||
#define BATTERY_PIN 35 // A battery voltage measurement pin, voltage divider connected here to measure battery voltage
|
||||
#define ADC_CHANNEL ADC1_GPIO35_CHANNEL
|
||||
#define ADC_MULTIPLIER 1.85 // (R1 = 470k, R2 = 680k)
|
||||
#define EXT_PWR_DETECT 4 // Pin to detect connected external power source for LILYGO® TTGO T-Energy T18 and other DIY boards
|
||||
#define EXT_NOTIFY_OUT 12 // Overridden default pin to use for Ext Notify Module (#975).
|
||||
#define LED_PIN 2 // add status LED (compatible with core-pcb and DIY targets)
|
||||
|
||||
#define LORA_DIO0 26 // a No connect on the SX1262/SX1268 module
|
||||
#define LORA_RESET 23 // RST for SX1276, and for SX1262/SX1268
|
||||
#define LORA_DIO1 33 // IRQ for SX1262/SX1268
|
||||
#define LORA_DIO2 32 // BUSY for SX1262/SX1268
|
||||
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262/SX1268, if DIO3 is high the TXCO is enabled
|
||||
|
||||
#define LORA_SCK 5
|
||||
#define LORA_MISO 19
|
||||
#define LORA_MOSI 27
|
||||
#define LORA_CS 18
|
||||
|
||||
// supported modules list
|
||||
#define USE_RF95 // RFM95/SX127x
|
||||
#define USE_SX1262
|
||||
#define USE_SX1268
|
||||
#define USE_LLCC68
|
||||
|
||||
// common pinouts for SX126X modules
|
||||
#define SX126X_CS 18 // NSS for SX126X
|
||||
#define SX126X_DIO1 LORA_DIO1
|
||||
#define SX126X_BUSY LORA_DIO2
|
||||
#define SX126X_RESET LORA_RESET
|
||||
#define SX126X_RXEN RADIOLIB_NC // Defining the RXEN ruins RFSwitching for the E22 900M30S in RadioLib
|
||||
#define SX126X_TXEN 13
|
||||
|
||||
// RX/TX for RFM95/SX127x
|
||||
#define RF95_RXEN 14
|
||||
#define RF95_TXEN 13
|
||||
|
||||
// Set lora.tx_power to 13 for Hydra or other E22 900M30S target due to PA
|
||||
#define SX126X_MAX_POWER 22
|
||||
|
||||
#ifdef EBYTE_E22
|
||||
// Internally the TTGO module hooks the SX126x-DIO2 in to control the TX/RX switch
|
||||
// (which is the default for the sx1262interface code)
|
||||
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
||||
#endif
|
||||
@@ -0,0 +1,57 @@
|
||||
// For OLED LCD
|
||||
#define I2C_SDA 21
|
||||
#define I2C_SCL 22
|
||||
|
||||
// GPS
|
||||
#undef GPS_RX_PIN
|
||||
#define GPS_RX_PIN 15
|
||||
|
||||
#define BUTTON_PIN 2 // The middle button GPIO on the T-Beam
|
||||
#define BUTTON_NEED_PULLUP
|
||||
#define EXT_NOTIFY_OUT 12 // Overridden default pin to use for Ext Notify Module (#975).
|
||||
|
||||
#define LORA_DIO0 26 // a No connect on the SX1262/SX1268 module
|
||||
#define LORA_RESET 27 // RST for SX1276, and for SX1262/SX1268
|
||||
#define LORA_DIO1 33 // IRQ for SX1262/SX1268
|
||||
#define LORA_DIO2 32 // BUSY for SX1262/SX1268
|
||||
#define LORA_DIO3 // Not connected on PCB, but internally on the TTGO SX1262/SX1268, if DIO3 is high the TXCO is enabled
|
||||
|
||||
// In transmitting, set TXEN as high communication level，RXEN pin is low level;
|
||||
// In receiving, set RXEN as high communication level, TXEN is lowlevel;
|
||||
// Before powering off, set TXEN、RXEN as low level.
|
||||
#define LORA_RXEN 14 // Input - RF switch RX control, connecting external MCU IO, valid in high level
|
||||
#define LORA_TXEN 13 // Input - RF switch TX control, connecting external MCU IO or DIO2, valid in high level
|
||||
|
||||
#undef LORA_SCK
|
||||
#define LORA_SCK 18
|
||||
#undef LORA_MISO
|
||||
#define LORA_MISO 19
|
||||
#undef LORA_MOSI
|
||||
#define LORA_MOSI 23
|
||||
#undef LORA_CS
|
||||
#define LORA_CS 5
|
||||
|
||||
// RX/TX for RFM95/SX127x
|
||||
#define RF95_RXEN LORA_RXEN
|
||||
#define RF95_TXEN LORA_TXEN
|
||||
// #define RF95_TCXO <GPIO#>
|
||||
|
||||
// common pinouts for SX126X modules
|
||||
#define SX126X_CS 5
|
||||
#define SX126X_DIO1 LORA_DIO1
|
||||
#define SX126X_BUSY LORA_DIO2
|
||||
#define SX126X_RESET LORA_RESET
|
||||
#define SX126X_RXEN LORA_RXEN
|
||||
#define SX126X_TXEN LORA_TXEN
|
||||
|
||||
// supported modules list
|
||||
#define USE_RF95 // RFM95/SX127x
|
||||
#define USE_SX1262
|
||||
#define USE_SX1268
|
||||
#define USE_LLCC68
|
||||
|
||||
#ifdef EBYTE_E22
|
||||
// Internally the TTGO module hooks the SX126x-DIO2 in to control the TX/RX switch
|
||||
// (which is the default for the sx1262interface code)
|
||||
#define SX126X_DIO3_TCXO_VOLTAGE 1.8
|
||||
#endif
|
||||
Reference in New Issue
Block a user