remove newline from logging statements in code. The LOG_* functions will now magically add it at the end.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* preliminary Othernet Dreamcatcher 2206 Support
Need to adapt to 2301 final version
* second target for latest revision
* preliminary Othernet Dreamcatcher 2206 Support
Need to adapt to 2301 final version
* second target for latest revision
* preliminary Othernet Dreamcatcher 2206 Support
Need to adapt to 2301 final version
* second target for latest revision
* address comments
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Potential fix for bad Rx performance on T1000-E
* validate and refactor RF switching, eliminate godmode
---------
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
* Refactor and consolidate windowing logic
* Trunk
* Fixes
* More
* Fix braces and remove unused now variables.
There was a brace in src/mesh/RadioLibInterface.cpp that was breaking
compile on some architectures.
Additionally, there were some brace errors in
src/modules/Telemetry/AirQualityTelemetry.cpp
src/modules/Telemetry/EnvironmentTelemetry.cpp
src/mesh/wifi/WiFiAPClient.cpp
Move throttle include in WifiAPClient.cpp to top.
Add Default.h to sleep.cpp
rest of files just remove unused now variables.
* Remove a couple more meows
---------
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Fix wio-tracker-1110 lora radio reset GPIO assignment
This fixes flaky lora radio init on this board.
* No need to keep lr11x0 radio config during sleep anymore, also stop TCXO
I think the problem (at least on the board I'm using for power testing
a wio tracker 1110) was that actually the RESET GPIO was not correct for
the radio. This led to the radio not being properly reinited after exiting
sleep mode.
Now that the GPIO is fixed I can enter deep sleep (fully shutting down
radio) and then later when the CPU resets, it can successfully init the
radio and send packets.
After this seeming success, I also turned off the TCXO during sleep and that
worked as well.
* feature-T1000-E: add Added the board definition for T1000-E
- integrate a script for rapid dependency download that is compatible with both Linux and Windows platforms.
- add the pin definitions for UART, SPI, GPIO, and other peripherals have been ensured to be correct.
- add the env configuration for PlatformIO.
* refact-T1000-E: redefine T1000-E board
* feature-T1000-E: add basic sensors
* feature-T1000-E: add button init
* feat: add DRADIOLIB_GODMODE defination for use function setDioAsRfSwitch to DIO LORA RF
* feat : add gps(GNSS_Airoha) sleep mode
* feat: add behavier when rec or send message
* chore: hang IIC bus usage to avoid sensor address conflict
* feat: add sensor data acquisition
* feat : support Airoha GPS
- add disable it in FSM
- update lookForTime and lookForLocation function
* fix: fix a bug
* version: change version to 0.9.0
* Update tracker-t1000-e.json
Remove a space
* Delete variants/tracker-t1000-e/run_once.sh
Delete not need as we will change platformio.ini
* Update platformio.ini
Update SoftDevice 7.3.0 usage in line with other lr1110 targets
Do we need to keep GODMODE ?
* fix: Button behavier incorrect bug
* fix:remove some invaild code of TextMessageModule
* fix: remove invaild comment
* version: change version to 0.9.1
- update mark's patch
- remove some invaild code and comments
- fix button behavier
* trunk format
* fix: HELTEC_CAPSULE_SENSOR_V3 block got accidentally deleted
* fix: EnvironmentTelemetry upstream merge went awry.
* fix: Added macro definitions to ensure correct operation of LORA section
* fix :GNSS_AIROHA macro defination in line with others
* fix: upstream backmerge accidentally.
* fix: wrap macro PIN_3V3_EN BUZZER_EN_PIN GNSS_AIROHA in the TRACKER_T1000_E macro guard
---------
Co-authored-by: Mark Trevor Birss <markbirss@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
* Turn off vscode cmake prompt - we don't use cmake on meshtastic
* Add rak4631_dap variant for debugging with NanoDAP debug probe device.
* The rak device can also run freertos (which is underneath nrf52 arduino)
* Add semihosting support for nrf52840 devices
Initial platformio.ini file only supports rak4630
Default to non TCP for the semihosting log output for now...
Fixes https://github.com/meshtastic/firmware/issues/4135
* powermon WIP (for https://github.com/meshtastic/firmware/issues/4136 )
* oops - mean't to mark the _dbg variant as an 'extra' board.
* powermon wip
* Make serial port on wio-sdk-wm1110 board work
By disabling the (inaccessible) adafruit USB
* Instrument (radiolib only for now) lora for powermon
per https://github.com/meshtastic/firmware/issues/4136
* powermon gps support
https://github.com/meshtastic/firmware/issues/4136
* Add CPU deep and light sleep powermon states
https://github.com/meshtastic/firmware/issues/4136
* Change the board/swversion bootstring so it is a new "structured" log msg.
* powermon wip
* add example script for getting esp S3 debugging working
Not yet used but I didn't want these nasty tricks to get lost yet.
* Add PowerMon reporting for screen and bluetooth pwr.
* make power.powermon_enables config setting work.
* update to latest protobufs
* fix bogus shellcheck warning
* make powermon optional (but default enabled because tiny and no runtime impact)
* tell vscode, if formatting, use whatever our trunk formatter wants
without this flag if the user has set some other formatter (clang)
in their user level settings, it will be looking in the wrong directory
for the clang options (we want the options in .trunk/clang)
Note: formatOnSave is true in master, which means a bunch of our older
files are non compliant and if you edit them it will generate lots of
formatting related diffs. I guess I'll start letting that happen with
my future commits ;-).
* add PowerStress module
* nrf52 arduino is built upon freertos, so let platformio debug it
* don't accidentally try to Segger ICE if we are using another ICE
* clean up RedirectablePrint::log so it doesn't have three very different implementations inline.
* remove NoopPrint - it is no longer needed
* when talking to API clients via serial, don't turn off log msgs instead encapsuate them
* fix the build - would loop forever if there were no files to send
* don't use Segger code if not talking to a Segger debugger
* when encapsulating logs, make sure the strings always has nul terminators
* nrf52 soft device will watchdog if you use ICE while BT on...
so have debugger disable bluetooth.
* Important to not print debug messages while writing to the toPhone scratch buffer
* don't include newlines if encapsulating log records as protobufs
* update to latest protobufs (needed for powermon goo)
* PowerStress WIP
* fix linter warning
* DOES NOT WORK
* trunk
* DOES NOT WORK
* trunk
* DOES NOT WORK
* trunk
* WIP: LR11x0 non functional interface code. Please don't expect a working firmware out of this! I don't know what i am doing! :-)
* trunk fmt
* use canon toolchain
* update and fix radiolib dependency
* Switch Radiolib back to GIT checkout
* enable tcxo and fix startReceive
* progress
* Correct midjudgement on scope of build defines.
* - enable peripheral power rail during startup init
- fix portduino builds
* add tracker pinout variant
* update to radiolib 6.6.0 API (aka: godmode is not for mere mortals)
* tracker is not so 'extra' any more
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
