* fix detection of lark weather station
* fix unit tests and add support for Dfrobot rain gauge
* fix name display on bootup
* fix gauge init logic
* trunk fmt
* Cleanup i2c scan logs and macro to save some bytes and remain consistent
* Functions are better than macros
* Exclude i2c scan for STM32
* Useless log
* T1000-E Peripherals
- enable intelligent charge controller signals
- enable Accelerometer
- enable internal I2C bus
- provide Power to Accelerometer
* POC Accelerometer Code (wakeScreen is moot for that device, just test if the driver works)
* fix building without the sensor
Implements an input driver utilising the MPR121 Touch IC and is compatible with common MPR121 keypad PCB's.
- Implements a "candybar" phone style 12-key keypad
- multiple taps to rotate through the character set
- longpress for navigation keys
- keymap to allow arbitrary routing of MPR121 pin to button configuration
- extendable to other key functions
- Integrates with the existing kbI2cBase implementation
- Works with CannedMessageModule Freetext mode
- Can be used with common MPR121 boards, such as https://www.amazon.com/MPR121-Capacitive-Keyboard-Buttons-Sensitive/dp/B083R89CHB/ref=sr_1_6
- Of use for PCB based radios, where some form of low surface area low component freetext input is required, but also without consuming too many IO pins.
- Tested on a T3S3 connected to Wire1 (Second) interface.
- Demonstration of functionality: https://youtu.be/UI6QP6nGvhY
remove newline from logging statements in code. The LOG_* functions will now magically add it at the end.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* preliminary Othernet Dreamcatcher 2206 Support
Need to adapt to 2301 final version
* second target for latest revision
* preliminary Othernet Dreamcatcher 2206 Support
Need to adapt to 2301 final version
* second target for latest revision
* preliminary Othernet Dreamcatcher 2206 Support
Need to adapt to 2301 final version
* second target for latest revision
* address comments
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Tom Fifield <tom@tomfifield.net>
* Add stub health telemetry module
* Add detection for MAX30102 Health Sensor
It lives on I2C bus at 0x57, which conflicts with an existing
sensor. Add code to check the PARTID register for its response 0x15
per spec.
* Add detection for MLX90614
An IR Temperature sensor suitable for livestock monitoring.
* Add libraries for MLX90614 and MAX30102 sensors
* Fix Trunk
* Add support for MLX90614 IR Temperature Sensor
* Add support for MAX30102 (Temperature)
* Make it build - our first HealthTelemetry on the mesh.
If a MAX30102 is connected, its temperature will be sent to the
mesh as HealthTelemetry.
* Add spo2 and heart rate calculations to MAX30102
* Switch MLX90614 to Adafruit library
Sparkfun was having fun with SDA/SCL variables which we can avoid
by switching to this highly similar library.
* Enable HealthTelemetry if MLX90614 detected
* Change MLX90614 emissivity for human skin.
* Add health screen!
* Remove autogenerated file from branch
* Preparing for review
* Fix MeshService master sync from before.
* Prepare for review
* For the americans
* Fix native build
* Fix for devices with no screen
* Remove extra log causing issues
---------
Co-authored-by: Tom Fifield <tom@tomfifield.net>
QMC5883L and HMC5883L are 3-axis compasses which are often confused.
As reported by @Africmod, we had the wrong I2C address for the QMC5883L.
This patch fixes the address and adds its HMC5883L so we keep info
about both.
Fixes https://github.com/meshtastic/firmware/issues/4144
* Added STK8xxxx Accelerometer chip
Added detection of STK8BA53 to I2C scanner.
Change the way and order MCP9808, lLISH3DH and STK8BA53 is detected since they all shares the same I2C address.
* Accelerometer support Radiomaster Bandit.
Enables tap to wake screen if enabled in config,
* Trunk
Trunk
* Make STM compile again and update toolchain. The binary is too big for the flash. WIP
* Making progress with OSFS, still WIP
* more progress, still too big. Adding RAK3172 to the equasion
* Make STM compile again and update toolchain. The binary is too big for the flash. WIP
* Making progress with OSFS, still WIP
* more progress, still too big. Adding RAK3172 to the equasion
* still too big
* minimize build
* trunk fmt
* fix a couple of symbol clashes
* trunk fmt
* down to 101% with a release vs. debug build and omitting the flash strings
* fix compilation
* fix compilation once more
* update protobufs linkage
* - Toolchain updated
- Fixed macro error
* silence compiler warning
note: do something about this assert...
* new toolkit and fix Power.cpp
* STM32WL make it fit (#4330)
* Add option to exclude I2C parts
The I2C hals and related code uses a significant amount of flash space and aren't required for a basic node.
* Add option to disable Admin and NodeInfo modules
Disabled by default in minimal build. This saves a significant amount of flash
* Disable unused hals
These use up significant flash
* Add float support for printf for debugging
Makes serial look nice for debugging
* This breaks my build for some reason
* These build flags can save a bit of flash
* Don't disable NodeInfo and Admin modules in minimal build
They fit in flash
* Don't include printf float support by default
Only useful for debugging
---------
Co-authored-by: Adam Lawson <dev@goshawk22.uk>
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Co-authored-by: Adam Lawson <dev@goshawk22.uk>
* Add SHT41 Serial to I2c Detection Code
On the Seeed Wio-WM1110 Dev Kit board, the SHT41 chip was being
incorrectly detected as SHT31.
This patch adds the necessary serial number for the SHT41 chip to
be correctly detected.
fixesmeshtastic/firmware#4221
* Add missing sensor read for SHT41
