* T-Watch WIP
* Updates
* Temp
* Update screen spi bus and and backlight en
* Peripherals progress
* Fixes
* Fixes
* Updates
* DRV scaffolding
* Fixed touch-screen driver selection. WIP on DRV haptic feedback
* DRV2605 pmu channel
* Trunk
* Fixes and defaults
* Dropped an s
* Move PMU and turn off screen that way
* Add t-deck and t-watch-s3 to CI and cleanup
* More cleanup
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* Fix LOG_DEBUG messages when no DEBUG_PORT.
* Fix LOG_DEBUG messages when no DEBUG_PORT.
- fix wrong debug print
- change shutdown logic for t-beam if PMU is detected
- wait for 10 seconds instead of 5 for shutdown and resurrect screen brightness adjust for @karamo
* Rearranging deck chairs, 900M22S working, 30S not
* We do have wire, just not where it's expected
* Put more of the module specific pins in their blocks
* tryfix compile with NO_SCREEN
* Portduino only: don't continue to try rebooting (#1887)
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
* Support for TLORA 2.1-1.8
* Don't allow arbitrary channel name for admin (#1886)
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Experimental DIY nrf52840 feather support (#1884)
* Experimental DIY nrf52840 feather support
* Fix target
* sx1262 wiring
* Remove lib
* Don't consider Response as ACK for FloodingRouter (#1885)
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix feather diy (#1892)
* Fix variant
* Fix feather diy target
* [modules][external notifications] allow select channel to listen to
* Fix feather diy pin mapping (#1894)
Thanks to @markbirss
* [create-pull-request] automated change
* Override Screen Autodtect
* Maybe fix crash of this board.
* Fixes reset loop with new espressif32 platform on tlora-v2
Sending a pulse to the OLED_RESET Pin 16 results in a reset loop using recent version of the espressif32 platform.
* Experiment with self hosted action runner
* Fix MQTT on ETH
* revert the tryfix
* Cheating
* Cleanup artifacts older than 1 month
* Update cleanup_artifacts.yml
* Update cleanup_artifacts.yml
* Update cleanup_artifacts.yml
* Delete cleanup_artifacts.yml
* fix: use RF95_IRQ for wakeup source in doLightSleep (#1899)
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Update protos
* Update protos
Co-authored-by: code8buster <communismisgreat@national.shitposting.agency>
Co-authored-by: Thomas Göttgens <tgoettgens@gmail.com>
Co-authored-by: GUVWAF <78759985+GUVWAF@users.noreply.github.com>
Co-authored-by: Mykhailo Lesyk <m@lesyk.org>
Co-authored-by: Mykhailo Lesyk <lesykm@users.noreply.github.com>
Co-authored-by: caveman99 <caveman99@users.noreply.github.com>
Co-authored-by: he-leon <he-leon@users.noreply.github.com>
Co-authored-by: Lars Weber <weber@weber-software.com>
* lay groundwork for a possible future architecture
* switch from feature opt-out to feature opt-in
* lay groundwork for a possible future architecture
* switch from feature opt-out to feature opt-in
* fix USE_RTC in variant.h for rak4631_epaper and t-echo
* ensure Screen.h is not included without configuration.h
Co-authored-by: Peter Lawrence <12226419+majbthrd@users.noreply.github.com>
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
bogus wakes on TBEAMS because the USB->SERIAL chip pulls the RX input
to ground. This feature is no longer needed because in !isRouter
nodes we force the node to never sleep anyways when on USB power.
// this doesn't work on TBEAMs when the USB is depowered (causes bogus interrupts)
// So we disable this "wake on serial" feature - because now when a TBEAM (only) has power connected it
// never tries to go to sleep if the user is using the API
// gpio_wakeup_enable((gpio_num_t)SERIAL0_RX_GPIO, GPIO_INTR_LOW_LEVEL);
oh - I think I found the problem (probably)! we were isolating gpio12 (which isn't used on other boards) to save power during sleep. gpio12 is the button for this board. @thomslik would you mind pulling this commit and seeing if it works better?
Note - we do this not by using the uart wake feature, but by the lower
power GPIO edge feature. Recommend sending "Z" 0x5A - because that has
many edges. Send the character 4 times to make sure the device is awake
* preflightSleep, notifySleep, notifyDeepSleep now allow arbitrary
drivers/devices/software to register for sleep notification.
* Use the proceeding to clean up MeshRadio - now the mesh radio is more
like an independent driver that doesn't care so much about other systems
* clean up MeshService so that it can work with zero MeshRadios added.
This is a prelude to supporting boards with multiple interfaces (wifi,
extra LORA radios etc) and allows development/testing in sim with a bare
ESP32 board
* Remove remaining ESP32 dependencies from the bare simulation target
this allows running on anything that implements the arduino API
because the ESP32 implementation will be different from NRF52
to make this possible I needed to decouple knowlege about bluetooth from
our mesh service. Instead mesh service now uses the Obserable pattern
to let any interested consumer get notified of important mesh changes
(currently that is only bluetooth, but really we should do the same
thing for decoupling the GUI 'app' from the mesh service)
@girtsf would you mind reviewing my Observer changes? I haven't written
C++ code in a long time ;-)
* to allow changing to new mesh transport
* to allow a different chipset for the radio
* to allow testing on hardware with a SimRadio
* new "bare" build env for a devboard with virtually no hardware
* make buttons optional
Also - now that he fixed that, we can leave PMU interrupts on across sleep
Hopefully the following line will properly credit him in the magic github
universe...
Co-authored-by: spattinson <spattinson@users.noreply.github.com>
Work towards separating out how Screen interacts with other stuff.
* `Screen` should now be thread-safe. All commands to it are put in a
queue and handled in `doTask` from the `loop()` task.
* Break dependency from `BluetoothUtil` to `Screen` by changing the
pairing request into a callback.
* All accesses to screen now happen through the class.
* Fix `drawRows` so that the text scrolls along with frame animations.
* Remove example code that wasn't used.
Root cause seems to be the axp192 interrupt, which on some boards fires
during sleep. I'm not sure why, but we don't need this yet, so leaving
masked during sleep.
