* Added STK8xxxx Accelerometer chip
Added detection of STK8BA53 to I2C scanner.
Change the way and order MCP9808, lLISH3DH and STK8BA53 is detected since they all shares the same I2C address.
* Accelerometer support Radiomaster Bandit.
Enables tap to wake screen if enabled in config,
* Trunk
Trunk
* t3s3 e-paper support
* remove GPS autodetect (which leads to crashes during startup when no GPS present)
* update EINK defines
* keep definitions for external GPS connector but disable GPS auto scan by default
* Add support for Adafruit Feather RP2040 with RFM95.
* Update mesh.pb.h
dropping this change from the file generated by the protobuf
* Update mesh.pb.h
remove these reverting changes
* Update mesh.pb.h
oops, missed a comma
(from src/extra_variants/README.md)
This directory tree is designed to solve two problems.
- The ESP32 arduino/platformio project doesn't support the nice "if initVariant() is found, call that after init" behavior of the nrf52 builds (they use initVariant() internally).
- Over the years a lot of 'board specific' init code has been added to init() in main.cpp. It would be great to have a general/clean mechanism to allow developers to specify board specific/unique code in a clean fashion without mucking in main.
So we are borrowing the initVariant() ideas here (by using weak gcc references). You can now define lateInitVariant() if your board needs it.
If you'd like a board specific variant to be run, add the variant.cpp file to an appropriately named
subdirectory and check for \_VARIANT_boardname in the cpp file (so that your code is only built for your board).
You'll need to define \_VARIANT_boardname in your corresponding variant.h file.
See existing boards for examples.
This approach has no added runtime cost.
* Initial support for RadioMaster Bandit.
* Different lighting can be made for Button 1 & 2 on the Bandit.
Changes to AmbientLighting will turn off af shutdown().
* Trunk
* Trunk again.
* Add support for Adafruit Feather RP2040 with RFM95.
* Update mesh.pb.h
dropping this change from the file generated by the protobuf
* Update mesh.pb.h
remove these reverting changes
* Update mesh.pb.h
oops, missed a comma
* Initial support for RadioMaster Bandit.
* Different lighting can be made for Button 1 & 2 on the Bandit.
Changes to AmbientLighting will turn off af shutdown().
* Trunk
* Trunk again.
Therefore don't just randomly be writing to a GPIO numbered -1
Instead just don't try to control the backlight
NOTE: I don't have a 'wiphone' to test with, but I saw this via inspection
while cleaning up some other stuff.
No need for _V05 and _V03 definitions - I think there was a slight misunderstanding
on how variant files are supposed to _decrease_ #ifdef code in the cpp files.
* Currently only on heltec tracker, but could use ADC_USE_PULLUP on other boards that could benefit
* Thanks @todd-herbert and @StevenCellist for the instructions ;-)
* Remove nasty Heltec_wireless #ifdefs that got somehow added to Power.cpp, instead use proper variant defs
* Cleanup adc enable/disable code a bit for less copy-paste cruft
* Update main.cpp
Add in TCXO_OPTIONAL variable for tcxoVoltage and a double-check for working in both modes.
* Update SX126xInterface.cpp
Make a change to the tcxoVoltage setting so that TCXO_OPTIONAL works if defined.
* Update variant.h
Added define for TCXO_OPTIONAL and the tcxoVoltage variable.
Added detail on the compatible boards.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Add heartbeat LED for HT-VME290 and HT-VME213
Not populated on original board, however revisions are now shipping which do have the LED
* Update outdated commenting
* Trunk strikes again
* Fix LED pinout for T-Echo board marked v1.0, date 2021-6-28
* Merge PR #420
* Fixed double and missing Default class.
* Use correct format specifier and fixed typo.
* Removed duplicate code.
* Fix error: #if with no expression
* Fix warning: extra tokens at end of #endif directive.
* Fix antenna switching logic. Complementary-pin control logic is required on the rp2040-lora board.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Radio Master Bandit 5-Way Joystick: first draft
Untested on genuine hardware
* "Okay" moves to next frame, even when canned message disabled
* Refactor to allow easier customization
* Implement feedback from testing
* guard toggleGPS()
* show "Shutting down.." screen
* split adhoc ping alert onto two lines
* Don't block while waiting for shutdown
Was preventing the alert from showing
* Guard against timesources from the mesh if we have good time
* Trunk
* Consider phone time in the past 24 hours authoritative as well
* Rename
* GPS can be null
* Declaration
* Remove RemoteHardware
* Explicitly remove GPS
* Exclude GPS earlier for RAK2560
* bug #4184: fix config file loss due to filesystem write errors
* Use SafeFile for atomic file writing (with xor checksum readback)
* Write db.proto last because it could be the largest file on the FS (and less critical)
* Don't keep a tmp file around while writing db.proto (because too big to fit two files in the filesystem)
* generate a new critial fault if we encounter errors writing to flash
either CriticalErrorCode_FLASH_CORRUPTION_RECOVERABLE or CriticalErrorCode_FLASH_CORRUPTION_UNRECOVERABLE
(depending on if the second write attempt worked)
* reformat the filesystem if we detect it is corrupted (then rewrite our config files) (only on nrf52 - not sure
yet if we should bother on ESP32)
* If we have to format the FS, make sure to preserve the oem.proto if it exists
* add logLegacy() so old C code in libs can log via our logging
* move filesList() to a better location (used only in developer builds)
* Reformat with "trunk fmt" to match our coding conventions
* for #4395: don't use .exists() to before attempting file open
If a LFS filesystem is corrupted, .exists() can fail when a mere .open()
attempt would have succeeded. Therefore better to do the .open() in hopes that
we can read the file (in case we need to reformat to fix the FS).
(Seen and confirmed in stress testing)
* for #4395 more fixes, see below for details:
* check for LFS assertion failures during file operations (needs customized lfs_util.h to provide suitable hooks)
* Remove fsCheck() because checking filesystem by writing to it is very high risk, it makes likelyhood that we will
be able to read the config protobufs quite low.
* Update the LFS inside of adafruitnrf52 to 1.7.2 (from their old 1.6.1) to get the following fix:
97d8d5e96a
* use disable_adafruit_usb.py now that we are (temporarily?) using a forked adafruit lib
We need to reach inside the adafruit project and turn off USE_TINYUSB, just doing that
from platformio.ini is no longer sufficient.
Tested on a wio-sdk-wm1110 board (which is the only board that had this problem)
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Update sensor drive and low power features.
* Update ST7789 TFT control logic.
* Update Heltec nRF board low power features.
* Update the GPS UART port pointer
* Add "Scan and Select" input method for canned messages
* Adapt canned message drawing if USE_EINK
* Indicate current selection with indent rather than inverse text
* Avoid large text on "sending" and delivery report pop-ups
* Fit SNR and RSSI details on screen
* Change hash function which detects changes in E-Ink images
The old function struggled to distingush between images on the canned-message frame, failing to update when scrolling between messages. No real justification for the new algorithm, other than "it works" and doesn't seem "too expensive". For context, this function runs once a second.
* Use canned messages (scan and select) by default with HT-VME213 and HT-VME290
* Guard for HAS_SCREEN
* Turn off vscode cmake prompt - we don't use cmake on meshtastic
* Add rak4631_dap variant for debugging with NanoDAP debug probe device.
* The rak device can also run freertos (which is underneath nrf52 arduino)
* Add semihosting support for nrf52840 devices
Initial platformio.ini file only supports rak4630
Default to non TCP for the semihosting log output for now...
Fixes https://github.com/meshtastic/firmware/issues/4135
* powermon WIP (for https://github.com/meshtastic/firmware/issues/4136 )
* oops - mean't to mark the _dbg variant as an 'extra' board.
* powermon wip
* Make serial port on wio-sdk-wm1110 board work
By disabling the (inaccessible) adafruit USB
* Instrument (radiolib only for now) lora for powermon
per https://github.com/meshtastic/firmware/issues/4136
* powermon gps support
https://github.com/meshtastic/firmware/issues/4136
* Add CPU deep and light sleep powermon states
https://github.com/meshtastic/firmware/issues/4136
* Change the board/swversion bootstring so it is a new "structured" log msg.
* powermon wip
* add example script for getting esp S3 debugging working
Not yet used but I didn't want these nasty tricks to get lost yet.
* Add PowerMon reporting for screen and bluetooth pwr.
* make power.powermon_enables config setting work.
* update to latest protobufs
* fix bogus shellcheck warning
* make powermon optional (but default enabled because tiny and no runtime impact)
* tell vscode, if formatting, use whatever our trunk formatter wants
without this flag if the user has set some other formatter (clang)
in their user level settings, it will be looking in the wrong directory
for the clang options (we want the options in .trunk/clang)
Note: formatOnSave is true in master, which means a bunch of our older
files are non compliant and if you edit them it will generate lots of
formatting related diffs. I guess I'll start letting that happen with
my future commits ;-).
* add PowerStress module
* nrf52 arduino is built upon freertos, so let platformio debug it
* don't accidentally try to Segger ICE if we are using another ICE
* clean up RedirectablePrint::log so it doesn't have three very different implementations inline.
* remove NoopPrint - it is no longer needed
* when talking to API clients via serial, don't turn off log msgs instead encapsuate them
* fix the build - would loop forever if there were no files to send
* don't use Segger code if not talking to a Segger debugger
* when encapsulating logs, make sure the strings always has nul terminators
* nrf52 soft device will watchdog if you use ICE while BT on...
so have debugger disable bluetooth.
* Important to not print debug messages while writing to the toPhone scratch buffer
* don't include newlines if encapsulating log records as protobufs
* update to latest protobufs (needed for powermon goo)
* PowerStress WIP
* for #4154 and #4136 add concept of dependent gpios...
Which is currently only tested with the LED but eventually
will be used for shared GPIO/screen power rail enable
and LED forcing (which is a sanity check in the power stress
testing)
* fix linter warning
* Transformer is a better name for the LED input > operation > output classes
* PMW led changes to work on esp32-s3
* power stress improvements
* allow ble logrecords to be fetched either by NOTIFY or INDICATE ble types
This allows 'lossless' log reading. If client has requested INDICATE
(rather than NOTIFY) each log record emitted via log() will have to fetched
by the client device before the meshtastic node can continue.
* Fix serious problem with nrf52 BLE logging.
When doing notifies of LogRecords it is important to use the
binary write routines - writing using the 'string' write won't work.
Because protobufs can contain \0 nuls inside of them which if being
parsed as a string will cause only a portion of the protobuf to be sent.
I noticed this because some log messages were not getting through.
* fix gpio transformer stuff to work correctly with LED_INVERTED
Thanks @todd-herbert for noticing this and the great stack trace.
The root cause was that I had accidentially shadowed outPin in a subclass
with an unneeded override. It would break on any board that had inverted
LED power.
fixes
https://github.com/meshtastic/firmware/pull/4230#pullrequestreview-2217389099
* Support driving multiple output gpios from one input.
While investigating https://github.com/meshtastic/firmware/pull/4230#pullrequestreview-2217389099
I noticed in variant.h that there are now apparently newer TBEAMs than mine
that have _both_ a GPIO based power LED and the PMU based LED. Add a splitter
so that we can drive two output GPIOs from one logical signal.
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
* Fix wio-tracker-1110 lora radio reset GPIO assignment
This fixes flaky lora radio init on this board.
* No need to keep lr11x0 radio config during sleep anymore, also stop TCXO
I think the problem (at least on the board I'm using for power testing
a wio tracker 1110) was that actually the RESET GPIO was not correct for
the radio. This led to the radio not being properly reinited after exiting
sleep mode.
Now that the GPIO is fixed I can enter deep sleep (fully shutting down
radio) and then later when the CPU resets, it can successfully init the
radio and send packets.
After this seeming success, I also turned off the TCXO during sleep and that
worked as well.
While working on #4378 I noticed a funny problem: the blinking system
LED was on during deep-sleep. Initially I thought it was some weird
sleep hw config thing but it turns out it was easier but more pervasive.
We had two different preprocessor symbols which both meant approximately the same
thing LED_INVERTED and LED_STATE_ON (though their polarity was opposite).
Some variant files were setting one, others were setting the other, and others were
setting both. heh.
In the case of the board I was testing (seeed tracker wio 1100) it was only setting one
and the default behavior for the other (for all boards) was incorrect. So I did a grep
and it seems like LED_STATE_ON was used more often, so I kept that one and removed
LED_INVERTED everywhere.
