QMC5883L and HMC5883L are 3-axis compasses which are often confused.
As reported by @Africmod, we had the wrong I2C address for the QMC5883L.
This patch fixes the address and adds its HMC5883L so we keep info
about both.
Fixes https://github.com/meshtastic/firmware/issues/4144
This getACK is used to look for ASCII responses, so print ASCII
when GPS_DEBUG is enabled.
This markedly assisted with recent AG3335 debugging. It works great
with other chips too (tested eg ATGM336H). Even UBLOX prints
understandable "GPTXT,01,01,01,PDTI inv format*35." responses.
Credit to bluebrolly. on discord.
* Added STK8xxxx Accelerometer chip
Added detection of STK8BA53 to I2C scanner.
Change the way and order MCP9808, lLISH3DH and STK8BA53 is detected since they all shares the same I2C address.
* Accelerometer support Radiomaster Bandit.
Enables tap to wake screen if enabled in config,
* Trunk
Trunk
* Add option to preserve private key for factory reset (config)
* Typo fix
* Copy the key in the right direction, and set the size.
* Don't set the key size back to 0 right after setting it to 32.
* Set the key size before using it to do a memcpy.
* Use the right key_size for backing up private_key
* Don't factoryReset() for a missing nodeDB
* Disable Bluetooth in AdminModule when resetting device settings or nodeDB to avoid race
* Add checks for valid objects before deinit bluetooth
* Add disableBluetooth to handleSetConfig, handleSetModuleConfig, and commit settings
---------
Co-authored-by: Jonathan Bennett <jbennett@incomsystems.biz>
* All the debug
* Change `memccpy()` to `memcpy()`
* Brint all the bytes of the MAC Address from the NodeDB
* Check for blank MAC Address in ourown NodeDB entry
* One more `memccpy()`
* Clean-up debug log
---------
Co-authored-by: GUVWAF <thijs@havinga.eu>
if u8i == 135, then u8i++ runs, the loop exits since u8i == 136,
then value for u8i is 136 after the for loop.
then in the next line, ntc_res2[u8i] will read past the end
of the array
At the moment if the result of sleepTime calculations comes out
to zero, we put the GPS into HARDSLEEP (losing all its status) and
then immediately make it ACTIVE again.
This patch avoids that toga.
fixes https://github.com/meshtastic/firmware/issues/4657
AG33352 is a Mediatek/Airoha GPS/GLONASS/Galileo/BeiDou receiver.
Patch adds relevant detection and setup code.
Thanks to Bluebrolly and kongduino for providing the relevant
information and testing.
This patch also fixes support for the A3335, which is a related chip.
The setup and detection code now works as tested on a real life
T-1000E!
Thanks to @gpsfan for the guidance.
* Don't filter PKI packets just for being encrypted.
* Add ok_to_mqtt config and bit
* Bitfield
* Adjust dontmqttmebro logic.
* Manipulate bitfield only in router.cpp
* Want_ack is not want_response
* Bitfield macros
* Use new Bitfield macro in MQTT.cpp
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
This patch takes inspiration from our I2CDetect code where we have
many sensors that can be detected rather simply. It creates a new
macro,
PROBE_SIMPLE(Chip name, Command to run, response, Driver, timeout)
and converts existing simple cases to use this macro.
* tryfix #4384 - don't assume we want that functionality if the Accelerometer was found. This is only for T-Watch
* Add config.display.wake_on_tap_or_motion default to RAK
---------
Co-authored-by: Ben Meadors <benmmeadors@gmail.com>
Fixes (#3618) by allowing more time for slower requests.
Resolve Syslog not maintaining client causing issues on RAK13800.
Resolve Ethernet static IP setting subnet as gateway IP.
Reduce comment and log message ambiguity around API.
Remove duplicate #if !MESHTASTIC_EXCLUDE_WEBSERVER block.
